@ -0,0 +1,76 @@ | |||
#include QMK_KEYBOARD_H | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
LAYOUT_ortho_5x4( | |||
KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, | |||
KC_P7, KC_P8, KC_P9, KC_PPLS, | |||
KC_P4, KC_P5, KC_P6, KC_PPLS, | |||
KC_P1, KC_P2, KC_P3, KC_PENT, | |||
KC_P0, KC_P0, KC_PDOT, KC_PENT), | |||
LAYOUT_ortho_5x4( | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), | |||
LAYOUT_ortho_5x4( | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), | |||
LAYOUT_ortho_5x4( | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, | |||
KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS) | |||
}; | |||
void matrix_init_user(void) { | |||
} | |||
void matrix_scan_user(void) { | |||
} | |||
bool process_record_user(uint16_t keycode, keyrecord_t *record) { | |||
return true; | |||
} | |||
void led_set_user(uint8_t usb_led) { | |||
if (usb_led & (1 << USB_LED_NUM_LOCK)) { | |||
} else { | |||
} | |||
if (usb_led & (1 << USB_LED_CAPS_LOCK)) { | |||
} else { | |||
} | |||
if (usb_led & (1 << USB_LED_SCROLL_LOCK)) { | |||
} else { | |||
} | |||
if (usb_led & (1 << USB_LED_COMPOSE)) { | |||
} else { | |||
} | |||
if (usb_led & (1 << USB_LED_KANA)) { | |||
} else { | |||
} | |||
} |
@ -0,0 +1,76 @@ | |||
# MCU name | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Bootloader selection | |||
# Teensy halfkay | |||
# Pro Micro caterina | |||
# Atmel DFU atmel-dfu | |||
# LUFA DFU lufa-dfu | |||
# QMK DFU qmk-dfu | |||
# atmega32a bootloadHID | |||
BOOTLOADER = caterina | |||
# Boot Section Size in *bytes* | |||
# OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = no # Console for debug(+400) | |||
COMMAND_ENABLE = no # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE = yes # USB Nkey Rollover | |||
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) | |||
UNICODE_ENABLE = no # Unicode | |||
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE = no # Audio output on port C6 | |||
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches | |||
# This is the VIA magic | |||
RAW_ENABLE = yes | |||
DYNAMIC_KEYMAP_ENABLE = yes | |||
SRC += keyboards/wilba_tech/wt_main.c | |||
LAYOUTS = ortho_5x4 numpad_5x4 |