@ -0,0 +1,14 @@ | |||
Chocopad | |||
======== | |||
A 4x4 macropad keyboard using Kailh PG1350 Lower Profile Choc switches. | |||
Keyboard Maintainer: Keebio | |||
Hardware Supported: Chocopad PCB, Arduino Pro Micro | |||
Hardware Availability: [Keebio](https://keeb.io) | |||
Make example for this keyboard (after setting up your build environment): | |||
make chocopad:default | |||
See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information. |
@ -0,0 +1 @@ | |||
#include "chocopad.h" |
@ -0,0 +1,32 @@ | |||
#ifndef CHOCOPAD_H | |||
#define CHOCOPAD_H | |||
#include "quantum.h" | |||
#define KEYMAP( \ | |||
A1, A2, A3, A4, \ | |||
B1, B2, B3, B4, \ | |||
C1, C2, C3, C4, \ | |||
D1, D2, D3, D4 \ | |||
) { \ | |||
{ A1, A2, A3, A4 }, \ | |||
{ B1, B2, B3, B4 }, \ | |||
{ C1, C2, C3, C4 }, \ | |||
{ D1, D2, D3, D4 } \ | |||
} | |||
// Used to create a keymap using only KC_ prefixed keys | |||
#define KC_KEYMAP( \ | |||
A1, A2, A3, A4, \ | |||
B1, B2, B3, B4, \ | |||
C1, C2, C3, C4, \ | |||
D1, D2, D3, D4 \ | |||
) \ | |||
KEYMAP( \ | |||
KC_##A1, KC_##A2, KC_##A3, KC_##A4, \ | |||
KC_##B1, KC_##B2, KC_##B3, KC_##B4, \ | |||
KC_##C1, KC_##C2, KC_##C3, KC_##C4, \ | |||
KC_##D1, KC_##D2, KC_##D3, KC_##D4 \ | |||
) | |||
#endif |
@ -0,0 +1,59 @@ | |||
#ifndef CONFIG_H | |||
#define CONFIG_H | |||
#include "config_common.h" | |||
/* USB Device descriptor parameter */ | |||
#define VENDOR_ID 0xCEEB | |||
#define PRODUCT_ID 0x1144 | |||
#define DEVICE_VER 0x0100 | |||
#define MANUFACTURER Keebio | |||
#define PRODUCT Chocopad | |||
#define DESCRIPTION 4x4 macropad using Kailh Choc low-profile switches | |||
/* key matrix size */ | |||
#define MATRIX_ROWS 4 | |||
#define MATRIX_COLS 4 | |||
/* key matrix pins */ | |||
#define MATRIX_ROW_PINS { D7, E6, B3, B2 } | |||
#define MATRIX_COL_PINS { D2, D4, F6, F5 } | |||
/* COL2ROW or ROW2COL */ | |||
#define DIODE_DIRECTION COL2ROW | |||
/* number of backlight levels */ | |||
#define BACKLIGHT_PIN B5 | |||
#define BACKLIGHT_LEVELS 6 | |||
/* Set 0 if debouncing isn't needed */ | |||
#define DEBOUNCING_DELAY 5 | |||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ | |||
#define LOCKING_SUPPORT_ENABLE | |||
/* Locking resynchronize hack */ | |||
#define LOCKING_RESYNC_ENABLE | |||
/* key combination for command */ | |||
#define IS_COMMAND() ( \ | |||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ | |||
) | |||
/* prevent stuck modifiers */ | |||
#define PREVENT_STUCK_MODIFIERS | |||
#ifdef RGB_DI_PIN | |||
#define RGBLIGHT_ANIMATIONS | |||
#define RGBLIGHT_HUE_STEP 8 | |||
#define RGBLIGHT_SAT_STEP 8 | |||
#define RGBLIGHT_VAL_STEP 8 | |||
#endif | |||
#define RGB_DI_PIN D3 | |||
#define RGBLIGHT_TIMER | |||
#define RGBLED_NUM 4 | |||
#define ws2812_PORTREG PORTD | |||
#define ws2812_DDRREG DDRD | |||
#endif |
@ -0,0 +1,6 @@ | |||
#ifndef CONFIG_USER_H | |||
#define CONFIG_USER_H | |||
#include "../../config.h" | |||
#endif |
@ -0,0 +1,61 @@ | |||
#include "chocopad.h" | |||
#define _BASE 0 | |||
#define _FN1 1 | |||
#define _FN2 2 | |||
#define KC_ KC_TRNS | |||
#define _______ KC_TRNS | |||
#define KC_X1 MO(_FN1) | |||
#define KC_X2 MO(_FN2) | |||
#define KC_RST RESET | |||
#define KC_BSTP BL_STEP | |||
#define KC_RTOG RGB_TOG | |||
#define KC_RMOD RGB_MOD | |||
#define KC_RHUI RGB_HUI | |||
#define KC_RHUD RGB_HUD | |||
#define KC_RSAI RGB_SAI | |||
#define KC_RSAD RGB_SAD | |||
#define KC_RVAI RGB_VAI | |||
#define KC_RVAD RGB_VAD | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
[_BASE] = KC_KEYMAP( | |||
//,----+----+----+----. | |||
PGUP,HOME, UP ,END , | |||
//|----+----+----+----| | |||
PGDN,LEFT,DOWN,RGHT, | |||
//|----+----+----+----| | |||
X2 ,VOLU,MPLY,MPRV, | |||
//|----+----+----+----| | |||
X1 ,VOLD,MUTE,MNXT | |||
//`----+----+----+----' | |||
), | |||
[_FN1] = KC_KEYMAP( | |||
//,----+----+----+----. | |||
ESC , P7 , P8 , P9 , | |||
//|----+----+----+----| | |||
TAB , P4 , P5 , P6 , | |||
//|----+----+----+----| | |||
ENT , P1 , P2 , P3 , | |||
//|----+----+----+----| | |||
, P0 , P0 ,DOT | |||
//`----+----+----+----' | |||
), | |||
[_FN2] = KC_KEYMAP( | |||
//,----+----+----+----. | |||
RTOG,RHUI,RSAI,RVAI, | |||
//|----+----+----+----| | |||
RMOD,RHUD,RSAD,RVAD, | |||
//|----+----+----+----| | |||
, , ,RST , | |||
//|----+----+----+----| | |||
BSTP, , , | |||
//`----+----+----+----' | |||
) | |||
}; |
@ -0,0 +1,5 @@ | |||
RGBLIGHT_ENABLE = yes | |||
ifndef QUANTUM_DIR | |||
include ../../../../Makefile | |||
endif |
@ -0,0 +1,56 @@ | |||
# MCU name | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = no # Console for debug(+400) | |||
COMMAND_ENABLE = no # Commands for debug and configuration | |||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality | |||
AUDIO_ENABLE = no | |||
RGBLIGHT_ENABLE = yes |