Added support for the Kitten Paw controllerpull/679/head
@ -0,0 +1,77 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u2 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= no # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
CUSTOM_MATRIX = yes | |||
SRC += matrix.c led.c | |||
ifndef QUANTUM_DIR | |||
include ../../Makefile | |||
endif | |||
@ -0,0 +1,162 @@ | |||
/* | |||
Copyright 2012 Jun Wako <wakojun@gmail.com> | |||
This program is free software: you can redistribute it and/or modify | |||
it under the terms of the GNU General Public License as published by | |||
the Free Software Foundation, either version 2 of the License, or | |||
(at your option) any later version. | |||
This program is distributed in the hope that it will be useful, | |||
but WITHOUT ANY WARRANTY; without even the implied warranty of | |||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |||
GNU General Public License for more details. | |||
You should have received a copy of the GNU General Public License | |||
along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
*/ | |||
#ifndef CONFIG_H | |||
#define CONFIG_H | |||
#include "config_common.h" | |||
/* USB Device descriptor parameter */ | |||
#define VENDOR_ID 0xFEED | |||
#define PRODUCT_ID 0x6050 | |||
#define DEVICE_VER 0x0104 | |||
#define MANUFACTURER Costar | |||
#define PRODUCT Majestouch | |||
/* key matrix size */ | |||
#define MATRIX_ROWS 8 | |||
#define MATRIX_COLS 18 | |||
/* | |||
* Keyboard Matrix Assignments | |||
* | |||
* Change this to how you wired your keyboard | |||
* COLS: AVR pins used for columns, left to right | |||
* ROWS: AVR pins used for rows, top to bottom | |||
* DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) | |||
* ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) | |||
* | |||
*/ | |||
//#define MATRIX_ROW_PINS { D0, D5 } | |||
//#define MATRIX_COL_PINS { F1, F0, B0 } | |||
//#define UNUSED_PINS | |||
/* COL2ROW or ROW2COL */ | |||
#define DIODE_DIRECTION COL2ROW | |||
// #define BACKLIGHT_PIN B7 | |||
// #define BACKLIGHT_BREATHING | |||
// #define BACKLIGHT_LEVELS 3 | |||
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ | |||
#define DEBOUNCING_DELAY 5 | |||
/* define if matrix has ghost (lacks anti-ghosting diodes) */ | |||
//#define MATRIX_HAS_GHOST | |||
/* number of backlight levels */ | |||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ | |||
#define LOCKING_SUPPORT_ENABLE | |||
/* Locking resynchronize hack */ | |||
#define LOCKING_RESYNC_ENABLE | |||
/* | |||
* Force NKRO | |||
* | |||
* Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved | |||
* state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the | |||
* makefile for this to work.) | |||
* | |||
* If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) | |||
* until the next keyboard reset. | |||
* | |||
* NKRO may prevent your keystrokes from being detected in the BIOS, but it is | |||
* fully operational during normal computer usage. | |||
* | |||
* For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) | |||
* or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by | |||
* bootmagic, NKRO mode will always be enabled until it is toggled again during a | |||
* power-up. | |||
* | |||
*/ | |||
//#define FORCE_NKRO | |||
/* | |||
* Magic Key Options | |||
* | |||
* Magic keys are hotkey commands that allow control over firmware functions of | |||
* the keyboard. They are best used in combination with the HID Listen program, | |||
* found here: https://www.pjrc.com/teensy/hid_listen.html | |||
* | |||
* The options below allow the magic key functionality to be changed. This is | |||
* useful if your keyboard/keypad is missing keys and you want magic key support. | |||
* | |||
*/ | |||
/* key combination for magic key command */ | |||
#define IS_COMMAND() ( \ | |||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ | |||
) | |||
/* control how magic key switches layers */ | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false | |||
/* override magic key keymap */ | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS | |||
//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM | |||
//#define MAGIC_KEY_HELP1 H | |||
//#define MAGIC_KEY_HELP2 SLASH | |||
//#define MAGIC_KEY_DEBUG D | |||
//#define MAGIC_KEY_DEBUG_MATRIX X | |||
//#define MAGIC_KEY_DEBUG_KBD K | |||
//#define MAGIC_KEY_DEBUG_MOUSE M | |||
//#define MAGIC_KEY_VERSION V | |||
//#define MAGIC_KEY_STATUS S | |||
//#define MAGIC_KEY_CONSOLE C | |||
//#define MAGIC_KEY_LAYER0_ALT1 ESC | |||
//#define MAGIC_KEY_LAYER0_ALT2 GRAVE | |||
//#define MAGIC_KEY_LAYER0 0 | |||
//#define MAGIC_KEY_LAYER1 1 | |||
//#define MAGIC_KEY_LAYER2 2 | |||
//#define MAGIC_KEY_LAYER3 3 | |||
//#define MAGIC_KEY_LAYER4 4 | |||
//#define MAGIC_KEY_LAYER5 5 | |||
//#define MAGIC_KEY_LAYER6 6 | |||
//#define MAGIC_KEY_LAYER7 7 | |||
//#define MAGIC_KEY_LAYER8 8 | |||
//#define MAGIC_KEY_LAYER9 9 | |||
//#define MAGIC_KEY_BOOTLOADER PAUSE | |||
//#define MAGIC_KEY_LOCK CAPS | |||
//#define MAGIC_KEY_EEPROM E | |||
//#define MAGIC_KEY_NKRO N | |||
//#define MAGIC_KEY_SLEEP_LED Z | |||
/* | |||
* Feature disable options | |||
* These options are also useful to firmware size reduction. | |||
*/ | |||
/* disable debug print */ | |||
//#define NO_DEBUG | |||
/* disable print */ | |||
//#define NO_PRINT | |||
/* disable action features */ | |||
//#define NO_ACTION_LAYER | |||
//#define NO_ACTION_TAPPING | |||
//#define NO_ACTION_ONESHOT | |||
//#define NO_ACTION_MACRO | |||
//#define NO_ACTION_FUNCTION | |||
#endif |
@ -0,0 +1,51 @@ | |||
#include "kitten_paw.h" | |||
enum layers { | |||
DEFAULT, | |||
}; | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
[DEFAULT] = KEYMAP(\ | |||
KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR,KC_SLCK,KC_PAUS, \ | |||
KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0,KC_MINS, KC_EQL,KC_BSPC, KC_INS,KC_HOME,KC_PGUP, KC_NLCK,KC_PSLS,KC_PAST,KC_PMNS, \ | |||
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P,KC_LBRC,KC_RBRC,KC_BSLS, KC_DEL, KC_END,KC_PGDN, KC_P7, KC_P8, KC_P9,KC_PPLS, \ | |||
KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L,KC_SCLN,KC_QUOT, KC_ENT, KC_P4, KC_P5, KC_P6, \ | |||
KC_LSFT,KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M,KC_COMM, KC_DOT,KC_SLSH, KC_RSFT, KC_UP, KC_P1, KC_P2, KC_P3,KC_PENT, \ | |||
KC_LCTL,KC_LGUI,KC_LALT, KC_SPC, KC_RALT,KC_RGUI,KC_MENU,KC_RCTL, KC_LEFT,KC_DOWN,KC_RGHT, KC_P0,KC_PDOT) | |||
}; | |||
const uint16_t PROGMEM fn_actions[] = { | |||
}; | |||
const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) | |||
{ | |||
// MACRODOWN only works in this function | |||
switch(id) { | |||
case 0: | |||
if (record->event.pressed) { | |||
register_code(KC_RSFT); | |||
} else { | |||
unregister_code(KC_RSFT); | |||
} | |||
break; | |||
} | |||
return MACRO_NONE; | |||
}; | |||
void matrix_init_user(void) { | |||
} | |||
void matrix_scan_user(void) { | |||
} | |||
bool process_record_user(uint16_t keycode, keyrecord_t *record) { | |||
return true; | |||
} | |||
void led_set_user(uint8_t usb_led) { | |||
} |
@ -0,0 +1,30 @@ | |||
#include "kitten_paw.h" | |||
void matrix_init_kb(void) { | |||
// put your keyboard start-up code here | |||
// runs once when the firmware starts up | |||
matrix_init_quantum(); | |||
matrix_init_user(); | |||
} | |||
void matrix_scan_kb(void) { | |||
// put your looping keyboard code here | |||
// runs every cycle (a lot) | |||
matrix_scan_quantum(); | |||
matrix_scan_user(); | |||
} | |||
bool process_record_kb(uint16_t keycode, keyrecord_t *record) { | |||
// put your per-action keyboard code here | |||
// runs for every action, just before processing by the firmware | |||
return process_record_user(keycode, record); | |||
} | |||
void led_set_kb(uint8_t usb_led) { | |||
// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here | |||
led_set_user(usb_led); | |||
} |
@ -0,0 +1,47 @@ | |||
#ifndef KITTEN_PAW_H | |||
#define KITTEN_PAW_H | |||
#include "quantum.h" | |||
// This a shortcut to help you visually see your layout. | |||
// The first section contains all of the arguements | |||
// The second converts the arguments into a two-dimensional array | |||
/* | |||
Matrix col/row mapping | |||
,----. ,-------------------. ,-------------------. ,-------------------. ,--------------. | |||
| J6 | | I4 | H4 | H2 | H6 | | A7 | E6 | D2 | D4 | | B4 | B7 | B6 | B0 | | C7 | C5 | A5 | | |||
`----' `-------------------' `-------------------' `-------------------' `--------------' | |||
,-------------------------------------------------------------------------. ,--------------. ,-------------------. | |||
| J4 | J7 | I7 | H7 | G7 | G4 | F4 | F7 | E7 | D7 | R7 | R4 | E4 | B2 | | L4 | O4 | Q4 | | K1 | L1 | Q1 | Q0 | | |||
|-------------------------------------------------------------------------| |--------------| |-------------------| | |||
| J2 | J5 | I5 | H5 | G5 | G2 | F2 | F5 | E5 | D5 | R5 | R2 | E2 | B3 | | K4 | O7 | Q7 | | K5 | L5 | Q5 | O5 | | |||
|-------------------------------------------------------------------------| '--------------' |-------------- | | |||
| O5 | J3 | I3 | H3 | G3 | G6 | F6 | F3 | E3 | D3 | R3 | R6 | B1 | | K2 | L2 | Q2 | | | |||
|-------------------------------------------------------------------------| ,----. |-------------------| | |||
| N2 | J1 | I1 | H1 | G1 | G0 | F0 | F1 | E1 | D1 | R0 | N3 | | O6 | | K3 | L3 | Q3 | O3 | | |||
|-------------------------------------------------------------------------| ,--------------. |-------------- | | |||
| A4 | P2 | C6 | K6 | C0 | M3 | D0 | A1 | | O0 | K0 | L0 | | L6 | Q6 | | | |||
`-------------------------------------------------------------------------' `--------------' `-------------------' | |||
*/ | |||
#define KEYMAP( \ | |||
KJ6, KI4, KH4, KH2, KH6, KA7, KE6, KD2, KD4, KB4, KB7, KB6, KB0, KC7, KC5, KA5, \ | |||
KJ4, KJ7, KI7, KH7, KG7, KG4, KF4, KF7, KE7, KD7, KR7, KR4, KE4, KB2, KL4, KO4, KQ4, KK1, KL1, KQ1, KQ0, \ | |||
KJ2, KJ5, KI5, KH5, KG5, KG2, KF2, KF5, KE5, KD5, KR5, KR2, KE2, KB3, KK4, KO7, KQ7, KK5, KL5, KQ5, KO5, \ | |||
KI2, KJ3, KI3, KH3, KG3, KG6, KF6, KF3, KE3, KD3, KR3, KR6, KB1, KK2, KL2, KQ2, \ | |||
KN2, KI6, KJ1, KI1, KH1, KG1, KG0, KF0, KF1, KE1, KD1, KR0, KN3, KO6, KK3, KL3, KQ3, KO3, \ | |||
KA4, KP2, KC6, KK6, KC0, KM3, KD0, KA1, KO0, KK0, KL0, KL6, KQ6 \ | |||
) \ | |||
{ \ | |||
{KC_NO, KB0, KC0, KD0,KC_NO, KF0, KG0,KC_NO,KC_NO,KC_NO, KK0, KL0,KC_NO,KC_NO, KO0,KC_NO, KQ0, KR0}, \ | |||
{ KA1, KB1,KC_NO, KD1, KE1, KF1, KG1, KH1, KI1, KJ1, KK1, KL1,KC_NO,KC_NO,KC_NO,KC_NO, KQ1,KC_NO}, \ | |||
{KC_NO, KB2,KC_NO, KD2, KE2, KF2, KG2, KH2, KI2, KJ2, KK2, KL2,KC_NO, KN2,KC_NO, KP2, KQ2, KR2}, \ | |||
{KC_NO, KB3,KC_NO, KD3, KE3, KF3, KG3, KH3, KI3, KJ3, KK3, KL3, KM3, KN3, KO3,KC_NO, KQ3, KR3}, \ | |||
{ KA4, KB4,KC_NO, KD4, KE4, KF4, KG4, KH4, KI4, KJ4, KK4, KL4,KC_NO,KC_NO, KO4,KC_NO, KQ4, KR4}, \ | |||
{ KA5,KC_NO, KC5, KD5, KE5, KF5, KG5, KH5, KI5, KJ5, KK5, KL5,KC_NO,KC_NO, KO5,KC_NO, KQ5, KR5}, \ | |||
{KC_NO, KB6, KC6,KC_NO, KE6, KF6, KG6, KH6, KI6, KJ6, KK6, KL6,KC_NO,KC_NO, KO6,KC_NO, KQ6, KR6}, \ | |||
{ KA7, KB7, KC7, KD7, KE7, KF7, KG7, KH7, KI7, KJ7,KC_NO,KC_NO,KC_NO,KC_NO, KO7,KC_NO, KQ7, KR7} \ | |||
} | |||
#endif |
@ -0,0 +1,47 @@ | |||
/* | |||
Copyright 2014 Ralf Schmitt <ralf@bunkertor.net> | |||
This program is free software: you can redistribute it and/or modify | |||
it under the terms of the GNU General Public License as published by | |||
the Free Software Foundation, either version 2 of the License, or | |||
(at your option) any later version. | |||
This program is distributed in the hope that it will be useful, | |||
but WITHOUT ANY WARRANTY; without even the implied warranty of | |||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |||
GNU General Public License for more details. | |||
You should have received a copy of the GNU General Public License | |||
along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
*/ | |||
#include <avr/io.h> | |||
#include "stdint.h" | |||
#include "led.h" | |||
/* LED pin configuration | |||
* | |||
* Scroll Lock PC5 | |||
* Caps Lock PC6 | |||
* Num Lock PB7 | |||
* | |||
*/ | |||
void led_set(uint8_t usb_led) { | |||
DDRB |= (1<<7); | |||
DDRC |= (1<<5) | (1<<6); | |||
if (usb_led & (1<<USB_LED_CAPS_LOCK)) | |||
PORTC &= ~(1<<6); | |||
else | |||
PORTC |= (1<<6); | |||
if (usb_led & (1<<USB_LED_NUM_LOCK)) | |||
PORTB &= ~(1<<7); | |||
else | |||
PORTB |= (1<<7); | |||
if (usb_led & (1<<USB_LED_SCROLL_LOCK)) | |||
PORTC &= ~(1<<5); | |||
else | |||
PORTC |= (1<<5); | |||
} |
@ -0,0 +1,164 @@ | |||
/* | |||
Copyright 2014 Ralf Schmitt <ralf@bunkertor.net> | |||
This program is free software: you can redistribute it and/or modify | |||
it under the terms of the GNU General Public License as published by | |||
the Free Software Foundation, either version 2 of the License, or | |||
(at your option) any later version. | |||
This program is distributed in the hope that it will be useful, | |||
but WITHOUT ANY WARRANTY; without even the implied warranty of | |||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |||
GNU General Public License for more details. | |||
You should have received a copy of the GNU General Public License | |||
along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
*/ | |||
#include <stdint.h> | |||
#include <stdbool.h> | |||
#include <avr/io.h> | |||
#include <util/delay.h> | |||
#include "print.h" | |||
#include "debug.h" | |||
#include "util.h" | |||
#include "matrix.h" | |||
#ifndef DEBOUNCING_DELAY | |||
# define DEBOUNCING_DELAY 5 | |||
#endif | |||
static uint8_t debouncing = DEBOUNCING_DELAY; | |||
static matrix_row_t matrix[MATRIX_ROWS]; | |||
static matrix_row_t matrix_debouncing[MATRIX_ROWS]; | |||
static uint8_t read_rows(void); | |||
static void select_col(uint8_t col); | |||
inline uint8_t matrix_rows(void) { | |||
return MATRIX_ROWS; | |||
} | |||
inline uint8_t matrix_cols(void) { | |||
return MATRIX_COLS; | |||
} | |||
/* Column pin configuration | |||
* | |||
* col: 0 1 2 3 4 5 6 7 | |||
* pin: PC7 PD5 PD3 PD1 PC2 PD6 PD4 PD2 | |||
* | |||
* Rrr pin configuration | |||
* | |||
* These rrrs uses one 74HC154 4 to 16 bit demultiplexer (low | |||
* active), together with 2 rrrs driven directly from the micro | |||
* controller, to control the 18 rrrs. The rrrs are driven from | |||
* pins B6,5,4,3,2,1,0. | |||
*/ | |||
void matrix_init(void) { | |||
DDRC &= ~0b10000100; // Row input pins | |||
DDRD &= ~0b01111110; | |||
PORTC |= 0b10000100; | |||
PORTD |= 0b01111110; | |||
DDRB |= 0b01111111; // Column output pins | |||
for (uint8_t i=0; i < MATRIX_ROWS; i++) { | |||
matrix[i] = 0; | |||
matrix_debouncing[i] = 0; | |||
} | |||
} | |||
uint8_t matrix_scan(void) { | |||
for (uint8_t col = 0; col < MATRIX_COLS; col++) { | |||
select_col(col); | |||
_delay_us(3); | |||
uint8_t rows = read_rows(); | |||
for (uint8_t row = 0; row < MATRIX_ROWS; row++) { | |||
bool prev_bit = matrix_debouncing[row] & ((matrix_row_t)1<<col); | |||
bool curr_bit = rows & (1<<row); | |||
if (prev_bit != curr_bit) { | |||
matrix_debouncing[row] ^= ((matrix_row_t)1<<col); | |||
debouncing = DEBOUNCING_DELAY; | |||
} | |||
} | |||
} | |||
if (debouncing) { | |||
if (--debouncing) { | |||
_delay_ms(1); | |||
} | |||
else { | |||
for (uint8_t i = 0; i < MATRIX_ROWS; i++) { | |||
matrix[i] = matrix_debouncing[i]; | |||
} | |||
} | |||
} | |||
return 1; | |||
} | |||
bool matrix_is_modified(void) { | |||
if (debouncing) | |||
return false; | |||
else | |||
return true; | |||
} | |||
inline bool matrix_is_on(uint8_t row, uint8_t col) { | |||
return (matrix[row] & ((matrix_row_t)1<<col)); | |||
} | |||
inline matrix_row_t matrix_get_row(uint8_t row) { | |||
return matrix[row]; | |||
} | |||
void matrix_print(void) { | |||
print("\nr/c 0123456789ABCDEF\n"); | |||
for (uint8_t row = 0; row < MATRIX_ROWS; row++) { | |||
xprintf("%02X: %032lb\n", row, bitrev32(matrix_get_row(row))); | |||
} | |||
} | |||
uint8_t matrix_key_count(void) { | |||
uint8_t count = 0; | |||
for (uint8_t i = 0; i < MATRIX_ROWS; i++) { | |||
count += bitpop32(matrix[i]); | |||
} | |||
return count; | |||
} | |||
static uint8_t read_rows(void) { | |||
return | |||
(PINC&(1<<7) ? 0 : (1<<0)) | | |||
(PIND&(1<<5) ? 0 : (1<<1)) | | |||
(PIND&(1<<3) ? 0 : (1<<2)) | | |||
(PIND&(1<<1) ? 0 : (1<<3)) | | |||
(PINC&(1<<2) ? 0 : (1<<4)) | | |||
(PIND&(1<<2) ? 0 : (1<<5)) | | |||
(PIND&(1<<4) ? 0 : (1<<6)) | | |||
(PIND&(1<<6) ? 0 : (1<<7)); | |||
} | |||
static void select_col(uint8_t col) { | |||
switch (col) { | |||
case 0: PORTB = (PORTB & ~0b01111111) | 0b01100100; break; | |||
case 1: PORTB = (PORTB & ~0b01111111) | 0b01101100; break; | |||
case 2: PORTB = (PORTB & ~0b01111111) | 0b01100010; break; | |||
case 3: PORTB = (PORTB & ~0b01111111) | 0b01111010; break; | |||
case 4: PORTB = (PORTB & ~0b01111111) | 0b01100110; break; | |||
case 5: PORTB = (PORTB & ~0b01111111) | 0b01110110; break; | |||
case 6: PORTB = (PORTB & ~0b01111111) | 0b01101110; break; | |||
case 7: PORTB = (PORTB & ~0b01111111) | 0b01111110; break; | |||
case 8: PORTB = (PORTB & ~0b01111111) | 0b01000001; break; | |||
case 9: PORTB = (PORTB & ~0b01111111) | 0b00100001; break; | |||
case 10: PORTB = (PORTB & ~0b01111111) | 0b01101010; break; | |||
case 11: PORTB = (PORTB & ~0b01111111) | 0b01110010; break; | |||
case 12: PORTB = (PORTB & ~0b01111111) | 0b01111100; break; | |||
case 13: PORTB = (PORTB & ~0b01111111) | 0b01110100; break; | |||
case 14: PORTB = (PORTB & ~0b01111111) | 0b01111000; break; | |||
case 15: PORTB = (PORTB & ~0b01111111) | 0b01110000; break; | |||
case 16: PORTB = (PORTB & ~0b01111111) | 0b01100000; break; | |||
case 17: PORTB = (PORTB & ~0b01111111) | 0b01101000; break; | |||
} | |||
} |
@ -0,0 +1,32 @@ | |||
kitten_paw keyboard firmware | |||
====================== | |||
This is the firmware for the 2016 revision of the Kitten Paw controller by Bathroom Epiphanies. | |||
Most of the boilerplate code is the work of [BathroomEpiphanies](https://github.com/BathroomEpiphanies). | |||
NKRO doesn't work at the moment, I don't know if I will take the time to find out how to fix this, so far 6KRO is enough for me. | |||
## Quantum MK Firmware | |||
For the full Quantum feature list, see [the parent readme.md](/doc/readme.md). | |||
## Building | |||
Download or clone the whole firmware and navigate to the keyboards/kitten_paw folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. | |||
Depending on which keymap you would like to use, you will have to compile slightly differently. | |||
### Default | |||
To build with the default keymap, simply run `make`. | |||
### Other Keymaps | |||
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files. | |||
To build the firmware binary hex file with a keymap just do `make` with `keymap` option like: | |||
``` | |||
$ make keymap=[default|jack|<name>] | |||
``` | |||
Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/` |