diff --git a/keyboards/wolfmarkclub/wm1/bootloader_defs.h b/keyboards/wolfmarkclub/wm1/bootloader_defs.h new file mode 100644 index 00000000000..393d70fdc6e --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/bootloader_defs.h @@ -0,0 +1,11 @@ +/* Address for jumping to bootloader on STM32 chips. */ +/* It is chip dependent, the correct number can be looked up here (page 175): + * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf + * This also requires a patch to chibios: + * /tmk_core/tool/chibios/ch-bootloader-jump.patch + */ + +// STM32F103 does not have a USB bootloader in ROM -- the WM1 +// has a usermode USB mass storage device bootloader at the normal +// boot address -- `0x08000000`. +#define STM32_BOOTLOADER_ADDRESS 0x80000000 diff --git a/keyboards/wolfmarkclub/wm1/chconf.h b/keyboards/wolfmarkclub/wm1/chconf.h new file mode 100644 index 00000000000..f5e471640c5 --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/chconf.h @@ -0,0 +1,714 @@ +/* + ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file rt/templates/chconf.h + * @brief Configuration file template. + * @details A copy of this file must be placed in each project directory, it + * contains the application specific kernel settings. + * + * @addtogroup config + * @details Kernel related settings and hooks. + * @{ + */ + +#ifndef CHCONF_H +#define CHCONF_H + +#define _CHIBIOS_RT_CONF_ +#define _CHIBIOS_RT_CONF_VER_6_0_ + +/*===========================================================================*/ +/** + * @name System timers settings + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System time counter resolution. + * @note Allowed values are 16 or 32 bits. + */ +#if !defined(CH_CFG_ST_RESOLUTION) +#define CH_CFG_ST_RESOLUTION 32 +#endif + +/** + * @brief System tick frequency. + * @details Frequency of the system timer that drives the system ticks. This + * setting also defines the system tick time unit. + */ +#if !defined(CH_CFG_ST_FREQUENCY) +#define CH_CFG_ST_FREQUENCY 100000 +#endif + +/** + * @brief Time intervals data size. + * @note Allowed values are 16, 32 or 64 bits. + */ +#if !defined(CH_CFG_INTERVALS_SIZE) +#define CH_CFG_INTERVALS_SIZE 32 +#endif + +/** + * @brief Time types data size. + * @note Allowed values are 16 or 32 bits. + */ +#if !defined(CH_CFG_TIME_TYPES_SIZE) +#define CH_CFG_TIME_TYPES_SIZE 32 +#endif + +/** + * @brief Time delta constant for the tick-less mode. + * @note If this value is zero then the system uses the classic + * periodic tick. This value represents the minimum number + * of ticks that is safe to specify in a timeout directive. + * The value one is not valid, timeouts are rounded up to + * this value. + */ +#if !defined(CH_CFG_ST_TIMEDELTA) +#define CH_CFG_ST_TIMEDELTA 0 +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel parameters and options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Round robin interval. + * @details This constant is the number of system ticks allowed for the + * threads before preemption occurs. Setting this value to zero + * disables the preemption for threads with equal priority and the + * round robin becomes cooperative. Note that higher priority + * threads can still preempt, the kernel is always preemptive. + * @note Disabling the round robin preemption makes the kernel more compact + * and generally faster. + * @note The round robin preemption is not supported in tickless mode and + * must be set to zero in that case. + */ +#if !defined(CH_CFG_TIME_QUANTUM) +#define CH_CFG_TIME_QUANTUM 0 +#endif + +/** + * @brief Managed RAM size. + * @details Size of the RAM area to be managed by the OS. If set to zero + * then the whole available RAM is used. The core memory is made + * available to the heap allocator and/or can be used directly through + * the simplified core memory allocator. + * + * @note In order to let the OS manage the whole RAM the linker script must + * provide the @p __heap_base__ and @p __heap_end__ symbols. + * @note Requires @p CH_CFG_USE_MEMCORE. + */ +#if !defined(CH_CFG_MEMCORE_SIZE) +#define CH_CFG_MEMCORE_SIZE 0 +#endif + +/** + * @brief Idle thread automatic spawn suppression. + * @details When this option is activated the function @p chSysInit() + * does not spawn the idle thread. The application @p main() + * function becomes the idle thread and must implement an + * infinite loop. + */ +#if !defined(CH_CFG_NO_IDLE_THREAD) +#define CH_CFG_NO_IDLE_THREAD FALSE +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Performance options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief OS optimization. + * @details If enabled then time efficient rather than space efficient code + * is used when two possible implementations exist. + * + * @note This is not related to the compiler optimization options. + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_OPTIMIZE_SPEED) +#define CH_CFG_OPTIMIZE_SPEED TRUE +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Subsystem options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Time Measurement APIs. + * @details If enabled then the time measurement APIs are included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_TM) +#define CH_CFG_USE_TM FALSE +#endif + +/** + * @brief Threads registry APIs. + * @details If enabled then the registry APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_REGISTRY) +#define CH_CFG_USE_REGISTRY TRUE +#endif + +/** + * @brief Threads synchronization APIs. + * @details If enabled then the @p chThdWait() function is included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_WAITEXIT) +#define CH_CFG_USE_WAITEXIT TRUE +#endif + +/** + * @brief Semaphores APIs. + * @details If enabled then the Semaphores APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_SEMAPHORES) +#define CH_CFG_USE_SEMAPHORES TRUE +#endif + +/** + * @brief Semaphores queuing mode. + * @details If enabled then the threads are enqueued on semaphores by + * priority rather than in FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#if !defined(CH_CFG_USE_SEMAPHORES_PRIORITY) +#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE +#endif + +/** + * @brief Mutexes APIs. + * @details If enabled then the mutexes APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_MUTEXES) +#define CH_CFG_USE_MUTEXES TRUE +#endif + +/** + * @brief Enables recursive behavior on mutexes. + * @note Recursive mutexes are heavier and have an increased + * memory footprint. + * + * @note The default is @p FALSE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#if !defined(CH_CFG_USE_MUTEXES_RECURSIVE) +#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE +#endif + +/** + * @brief Conditional Variables APIs. + * @details If enabled then the conditional variables APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#if !defined(CH_CFG_USE_CONDVARS) +#define CH_CFG_USE_CONDVARS TRUE +#endif + +/** + * @brief Conditional Variables APIs with timeout. + * @details If enabled then the conditional variables APIs with timeout + * specification are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_CONDVARS. + */ +#if !defined(CH_CFG_USE_CONDVARS_TIMEOUT) +#define CH_CFG_USE_CONDVARS_TIMEOUT FALSE +#endif + +/** + * @brief Events Flags APIs. + * @details If enabled then the event flags APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_EVENTS) +#define CH_CFG_USE_EVENTS TRUE +#endif + +/** + * @brief Events Flags APIs with timeout. + * @details If enabled then the events APIs with timeout specification + * are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_EVENTS. + */ +#if !defined(CH_CFG_USE_EVENTS_TIMEOUT) +#define CH_CFG_USE_EVENTS_TIMEOUT TRUE +#endif + +/** + * @brief Synchronous Messages APIs. + * @details If enabled then the synchronous messages APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_MESSAGES) +#define CH_CFG_USE_MESSAGES TRUE +#endif + +/** + * @brief Synchronous Messages queuing mode. + * @details If enabled then messages are served by priority rather than in + * FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_MESSAGES. + */ +#if !defined(CH_CFG_USE_MESSAGES_PRIORITY) +#define CH_CFG_USE_MESSAGES_PRIORITY FALSE +#endif + +/** + * @brief Mailboxes APIs. + * @details If enabled then the asynchronous messages (mailboxes) APIs are + * included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#if !defined(CH_CFG_USE_MAILBOXES) +#define CH_CFG_USE_MAILBOXES TRUE +#endif + +/** + * @brief Core Memory Manager APIs. + * @details If enabled then the core memory manager APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_MEMCORE) +#define CH_CFG_USE_MEMCORE TRUE +#endif + +/** + * @brief Heap Allocator APIs. + * @details If enabled then the memory heap allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or + * @p CH_CFG_USE_SEMAPHORES. + * @note Mutexes are recommended. + */ +#if !defined(CH_CFG_USE_HEAP) +#define CH_CFG_USE_HEAP TRUE +#endif + +/** + * @brief Memory Pools Allocator APIs. + * @details If enabled then the memory pools allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_MEMPOOLS) +#define CH_CFG_USE_MEMPOOLS FALSE +#endif + +/** + * @brief Objects FIFOs APIs. + * @details If enabled then the objects FIFOs APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_OBJ_FIFOS) +#define CH_CFG_USE_OBJ_FIFOS FALSE +#endif + +/** + * @brief Pipes APIs. + * @details If enabled then the pipes APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#if !defined(CH_CFG_USE_PIPES) +#define CH_CFG_USE_PIPES FALSE +#endif + +/** + * @brief Dynamic Threads APIs. + * @details If enabled then the dynamic threads creation APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_WAITEXIT. + * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. + */ +#if !defined(CH_CFG_USE_DYNAMIC) +#define CH_CFG_USE_DYNAMIC FALSE +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Objects factory options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Objects Factory APIs. + * @details If enabled then the objects factory APIs are included in the + * kernel. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_CFG_USE_FACTORY) +#define CH_CFG_USE_FACTORY FALSE +#endif + +/** + * @brief Maximum length for object names. + * @details If the specified length is zero then the name is stored by + * pointer but this could have unintended side effects. + */ +#if !defined(CH_CFG_FACTORY_MAX_NAMES_LENGTH) +#define CH_CFG_FACTORY_MAX_NAMES_LENGTH 8 +#endif + +/** + * @brief Enables the registry of generic objects. + */ +#if !defined(CH_CFG_FACTORY_OBJECTS_REGISTRY) +#define CH_CFG_FACTORY_OBJECTS_REGISTRY FALSE +#endif + +/** + * @brief Enables factory for generic buffers. + */ +#if !defined(CH_CFG_FACTORY_GENERIC_BUFFERS) +#define CH_CFG_FACTORY_GENERIC_BUFFERS FALSE +#endif + +/** + * @brief Enables factory for semaphores. + */ +#if !defined(CH_CFG_FACTORY_SEMAPHORES) +#define CH_CFG_FACTORY_SEMAPHORES FALSE +#endif + +/** + * @brief Enables factory for mailboxes. + */ +#if !defined(CH_CFG_FACTORY_MAILBOXES) +#define CH_CFG_FACTORY_MAILBOXES FALSE +#endif + +/** + * @brief Enables factory for objects FIFOs. + */ +#if !defined(CH_CFG_FACTORY_OBJ_FIFOS) +#define CH_CFG_FACTORY_OBJ_FIFOS FALSE +#endif + +/** + * @brief Enables factory for Pipes. + */ +#if !defined(CH_CFG_FACTORY_PIPES) || defined(__DOXYGEN__) +#define CH_CFG_FACTORY_PIPES FALSE +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Debug options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Debug option, kernel statistics. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_DBG_STATISTICS) +#define CH_DBG_STATISTICS FALSE +#endif + +/** + * @brief Debug option, system state check. + * @details If enabled the correct call protocol for system APIs is checked + * at runtime. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_DBG_SYSTEM_STATE_CHECK) +#define CH_DBG_SYSTEM_STATE_CHECK FALSE +#endif + +/** + * @brief Debug option, parameters checks. + * @details If enabled then the checks on the API functions input + * parameters are activated. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_DBG_ENABLE_CHECKS) +#define CH_DBG_ENABLE_CHECKS FALSE +#endif + +/** + * @brief Debug option, consistency checks. + * @details If enabled then all the assertions in the kernel code are + * activated. This includes consistency checks inside the kernel, + * runtime anomalies and port-defined checks. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_DBG_ENABLE_ASSERTS) +#define CH_DBG_ENABLE_ASSERTS FALSE +#endif + +/** + * @brief Debug option, trace buffer. + * @details If enabled then the trace buffer is activated. + * + * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. + */ +#if !defined(CH_DBG_TRACE_MASK) +#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED +#endif + +/** + * @brief Trace buffer entries. + * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is + * different from @p CH_DBG_TRACE_MASK_DISABLED. + */ +#if !defined(CH_DBG_TRACE_BUFFER_SIZE) +#define CH_DBG_TRACE_BUFFER_SIZE 128 +#endif + +/** + * @brief Debug option, stack checks. + * @details If enabled then a runtime stack check is performed. + * + * @note The default is @p FALSE. + * @note The stack check is performed in a architecture/port dependent way. + * It may not be implemented or some ports. + * @note The default failure mode is to halt the system with the global + * @p panic_msg variable set to @p NULL. + */ +#if !defined(CH_DBG_ENABLE_STACK_CHECK) +#define CH_DBG_ENABLE_STACK_CHECK FALSE +#endif + +/** + * @brief Debug option, stacks initialization. + * @details If enabled then the threads working area is filled with a byte + * value when a thread is created. This can be useful for the + * runtime measurement of the used stack. + * + * @note The default is @p FALSE. + */ +#if !defined(CH_DBG_FILL_THREADS) +#define CH_DBG_FILL_THREADS FALSE +#endif + +/** + * @brief Debug option, threads profiling. + * @details If enabled then a field is added to the @p thread_t structure that + * counts the system ticks occurred while executing the thread. + * + * @note The default is @p FALSE. + * @note This debug option is not currently compatible with the + * tickless mode. + */ +#if !defined(CH_DBG_THREADS_PROFILING) +#define CH_DBG_THREADS_PROFILING FALSE +#endif + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel hooks + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System structure extension. + * @details User fields added to the end of the @p ch_system_t structure. + */ +#define CH_CFG_SYSTEM_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief System initialization hook. + * @details User initialization code added to the @p chSysInit() function + * just before interrupts are enabled globally. + */ +#define CH_CFG_SYSTEM_INIT_HOOK() { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads descriptor structure extension. + * @details User fields added to the end of the @p thread_t structure. + */ +#define CH_CFG_THREAD_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief Threads initialization hook. + * @details User initialization code added to the @p _thread_init() function. + * + * @note It is invoked from within @p _thread_init() and implicitly from all + * the threads creation APIs. + */ +#define CH_CFG_THREAD_INIT_HOOK(tp) { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads finalization hook. + * @details User finalization code added to the @p chThdExit() API. + */ +#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ + /* Add threads finalization code here.*/ \ +} + +/** + * @brief Context switch hook. + * @details This hook is invoked just before switching between threads. + */ +#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ + /* Context switch code here.*/ \ +} + +/** + * @brief ISR enter hook. + */ +#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ + /* IRQ prologue code here.*/ \ +} + +/** + * @brief ISR exit hook. + */ +#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ + /* IRQ epilogue code here.*/ \ +} + +/** + * @brief Idle thread enter hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to activate a power saving mode. + */ +#define CH_CFG_IDLE_ENTER_HOOK() { \ + /* Idle-enter code here.*/ \ +} + +/** + * @brief Idle thread leave hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to deactivate a power saving mode. + */ +#define CH_CFG_IDLE_LEAVE_HOOK() { \ + /* Idle-leave code here.*/ \ +} + +/** + * @brief Idle Loop hook. + * @details This hook is continuously invoked by the idle thread loop. + */ +#define CH_CFG_IDLE_LOOP_HOOK() { \ + /* Idle loop code here.*/ \ +} + +/** + * @brief System tick event hook. + * @details This hook is invoked in the system tick handler immediately + * after processing the virtual timers queue. + */ +#define CH_CFG_SYSTEM_TICK_HOOK() { \ + /* System tick event code here.*/ \ +} + +/** + * @brief System halt hook. + * @details This hook is invoked in case to a system halting error before + * the system is halted. + */ +#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ + /* System halt code here.*/ \ +} + +/** + * @brief Trace hook. + * @details This hook is invoked each time a new record is written in the + * trace buffer. + */ +#define CH_CFG_TRACE_HOOK(tep) { \ + /* Trace code here.*/ \ +} + +/** @} */ + +/*===========================================================================*/ +/* Port-specific settings (override port settings defaulted in chcore.h). */ +/*===========================================================================*/ + +#endif /* CHCONF_H */ + +/** @} */ diff --git a/keyboards/wolfmarkclub/wm1/config.h b/keyboards/wolfmarkclub/wm1/config.h new file mode 100644 index 00000000000..d014fdcf8aa --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/config.h @@ -0,0 +1,80 @@ +/* +Copyright 2015 Jun Wako + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#pragma once + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x2B29 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Wolfmark Club +#define PRODUCT WM1 +#define DESCRIPTION Ergo 65% + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 15 + +// 0 1 2 3 4 5 6 7 8 9 A B C D E +#define MATRIX_ROW_PINS { C4, A7, A6, A5, A4 } +#define MATRIX_COL_PINS { B10, B11, B12, B13, B14, B15, C6, C10, C11, C12, D2, B5, B6, B7, B8 } + +#define DIODE_DIRECTION COL2ROW + +/* number of backlight levels */ +// #define BACKLIGHT_PIN A2 +// #ifdef BACKLIGHT_PIN +// #define BACKLIGHT_LEVELS 5 +// #endif + +#define RGB_DI_PIN A3 +#ifdef RGB_DI_PIN +#define RGBLED_NUM 18 +#define RGBLIGHT_ANIMATIONS +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 +#define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */ +#define RGBLIGHT_SLEEP /* If defined, the RGB lighting will be switched off when the host goes to sleep */ +#endif +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCE 5 +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION diff --git a/keyboards/wolfmarkclub/wm1/halconf.h b/keyboards/wolfmarkclub/wm1/halconf.h new file mode 100644 index 00000000000..ff5ae7e8a5f --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/halconf.h @@ -0,0 +1,525 @@ +/* + ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/halconf.h + * @brief HAL configuration header. + * @details HAL configuration file, this file allows to enable or disable the + * various device drivers from your application. You may also use + * this file in order to override the device drivers default settings. + * + * @addtogroup HAL_CONF + * @{ + */ + +#ifndef HALCONF_H +#define HALCONF_H + +#define _CHIBIOS_HAL_CONF_ +#define _CHIBIOS_HAL_CONF_VER_7_0_ + +#include "mcuconf.h" + +/** + * @brief Enables the PAL subsystem. + */ +#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) +#define HAL_USE_PAL TRUE +#endif + +/** + * @brief Enables the ADC subsystem. + */ +#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) +#define HAL_USE_ADC FALSE +#endif + +/** + * @brief Enables the CAN subsystem. + */ +#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) +#define HAL_USE_CAN FALSE +#endif + +/** + * @brief Enables the cryptographic subsystem. + */ +#if !defined(HAL_USE_CRY) || defined(__DOXYGEN__) +#define HAL_USE_CRY FALSE +#endif + +/** + * @brief Enables the DAC subsystem. + */ +#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) +#define HAL_USE_DAC FALSE +#endif + +/** + * @brief Enables the GPT subsystem. + */ +#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) +#define HAL_USE_GPT FALSE +#endif + +/** + * @brief Enables the I2C subsystem. + */ +#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) +#define HAL_USE_I2C FALSE +#endif + +/** + * @brief Enables the I2S subsystem. + */ +#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) +#define HAL_USE_I2S FALSE +#endif + +/** + * @brief Enables the ICU subsystem. + */ +#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) +#define HAL_USE_ICU FALSE +#endif + +/** + * @brief Enables the MAC subsystem. + */ +#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) +#define HAL_USE_MAC FALSE +#endif + +/** + * @brief Enables the MMC_SPI subsystem. + */ +#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) +#define HAL_USE_MMC_SPI FALSE +#endif + +/** + * @brief Enables the PWM subsystem. + */ +#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) +#define HAL_USE_PWM TRUE +#endif + +/** + * @brief Enables the RTC subsystem. + */ +#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) +#define HAL_USE_RTC FALSE +#endif + +/** + * @brief Enables the SDC subsystem. + */ +#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) +#define HAL_USE_SDC FALSE +#endif + +/** + * @brief Enables the SERIAL subsystem. + */ +#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL FALSE +#endif + +/** + * @brief Enables the SERIAL over USB subsystem. + */ +#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL_USB FALSE +#endif + +/** + * @brief Enables the SIO subsystem. + */ +#if !defined(HAL_USE_SIO) || defined(__DOXYGEN__) +#define HAL_USE_SIO FALSE +#endif + +/** + * @brief Enables the SPI subsystem. + */ +#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) +#define HAL_USE_SPI FALSE +#endif + +/** + * @brief Enables the TRNG subsystem. + */ +#if !defined(HAL_USE_TRNG) || defined(__DOXYGEN__) +#define HAL_USE_TRNG FALSE +#endif + +/** + * @brief Enables the UART subsystem. + */ +#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) +#define HAL_USE_UART FALSE +#endif + +/** + * @brief Enables the USB subsystem. + */ +#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) +#define HAL_USE_USB TRUE +#endif + +/** + * @brief Enables the WDG subsystem. + */ +#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) +#define HAL_USE_WDG FALSE +#endif + +/** + * @brief Enables the WSPI subsystem. + */ +#if !defined(HAL_USE_WSPI) || defined(__DOXYGEN__) +#define HAL_USE_WSPI FALSE +#endif + +/*===========================================================================*/ +/* PAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(PAL_USE_CALLBACKS) || defined(__DOXYGEN__) +#define PAL_USE_CALLBACKS FALSE +#endif + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(PAL_USE_WAIT) || defined(__DOXYGEN__) +#define PAL_USE_WAIT FALSE +#endif + +/*===========================================================================*/ +/* ADC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) +#define ADC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define ADC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* CAN driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Sleep mode related APIs inclusion switch. + */ +#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) +#define CAN_USE_SLEEP_MODE TRUE +#endif + +/** + * @brief Enforces the driver to use direct callbacks rather than OSAL events. + */ +#if !defined(CAN_ENFORCE_USE_CALLBACKS) || defined(__DOXYGEN__) +#define CAN_ENFORCE_USE_CALLBACKS FALSE +#endif + +/*===========================================================================*/ +/* CRY driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the SW fall-back of the cryptographic driver. + * @details When enabled, this option, activates a fall-back software + * implementation for algorithms not supported by the underlying + * hardware. + * @note Fall-back implementations may not be present for all algorithms. + */ +#if !defined(HAL_CRY_USE_FALLBACK) || defined(__DOXYGEN__) +#define HAL_CRY_USE_FALLBACK FALSE +#endif + +/** + * @brief Makes the driver forcibly use the fall-back implementations. + */ +#if !defined(HAL_CRY_ENFORCE_FALLBACK) || defined(__DOXYGEN__) +#define HAL_CRY_ENFORCE_FALLBACK FALSE +#endif + +/*===========================================================================*/ +/* DAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(DAC_USE_WAIT) || defined(__DOXYGEN__) +#define DAC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p dacAcquireBus() and @p dacReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(DAC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define DAC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* I2C driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the mutual exclusion APIs on the I2C bus. + */ +#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define I2C_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* MAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the zero-copy API. + */ +#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) +#define MAC_USE_ZERO_COPY FALSE +#endif + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) +#define MAC_USE_EVENTS TRUE +#endif + +/*===========================================================================*/ +/* MMC_SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + * This option is recommended also if the SPI driver does not + * use a DMA channel and heavily loads the CPU. + */ +#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) +#define MMC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SDC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Number of initialization attempts before rejecting the card. + * @note Attempts are performed at 10mS intervals. + */ +#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) +#define SDC_INIT_RETRY 100 +#endif + +/** + * @brief Include support for MMC cards. + * @note MMC support is not yet implemented so this option must be kept + * at @p FALSE. + */ +#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) +#define SDC_MMC_SUPPORT FALSE +#endif + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + */ +#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) +#define SDC_NICE_WAITING TRUE +#endif + +/** + * @brief OCR initialization constant for V20 cards. + */ +#if !defined(SDC_INIT_OCR_V20) || defined(__DOXYGEN__) +#define SDC_INIT_OCR_V20 0x50FF8000U +#endif + +/** + * @brief OCR initialization constant for non-V20 cards. + */ +#if !defined(SDC_INIT_OCR) || defined(__DOXYGEN__) +#define SDC_INIT_OCR 0x80100000U +#endif + +/*===========================================================================*/ +/* SERIAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Default bit rate. + * @details Configuration parameter, this is the baud rate selected for the + * default configuration. + */ +#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) +#define SERIAL_DEFAULT_BITRATE 38400 +#endif + +/** + * @brief Serial buffers size. + * @details Configuration parameter, you can change the depth of the queue + * buffers depending on the requirements of your application. + * @note The default is 16 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_BUFFERS_SIZE 16 +#endif + +/*===========================================================================*/ +/* SERIAL_USB driver related setting. */ +/*===========================================================================*/ + +/** + * @brief Serial over USB buffers size. + * @details Configuration parameter, the buffer size must be a multiple of + * the USB data endpoint maximum packet size. + * @note The default is 256 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_SIZE 1 +#endif + +/** + * @brief Serial over USB number of buffers. + * @note The default is 2 buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_NUMBER 2 +#endif + +/*===========================================================================*/ +/* SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) +#define SPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables circular transfers APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_CIRCULAR) || defined(__DOXYGEN__) +#define SPI_USE_CIRCULAR FALSE +#endif + + +/** + * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define SPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +/** + * @brief Handling method for SPI CS line. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_SELECT_MODE) || defined(__DOXYGEN__) +#define SPI_SELECT_MODE SPI_SELECT_MODE_PAD +#endif + +/*===========================================================================*/ +/* UART driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__) +#define UART_USE_WAIT FALSE +#endif + +/** + * @brief Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define UART_USE_MUTUAL_EXCLUSION FALSE +#endif + +/*===========================================================================*/ +/* USB driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) +#define USB_USE_WAIT TRUE +#endif + +/*===========================================================================*/ +/* WSPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(WSPI_USE_WAIT) || defined(__DOXYGEN__) +#define WSPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p wspiAcquireBus() and @p wspiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(WSPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define WSPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +#endif /* HALCONF_H */ + +/** @} */ diff --git a/keyboards/wolfmarkclub/wm1/info.json b/keyboards/wolfmarkclub/wm1/info.json new file mode 100644 index 00000000000..651d0d5e97c --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/info.json @@ -0,0 +1,12 @@ +{ + "keyboard_name": "Wolfmark Club WM1", + "url": "", + "maintainer": "qmk", + "width": 18.25, + "height": 5.25, + "layouts": { + "LAYOUT": { + "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":8.75, "y":0}, {"x":9.75, "y":0}, {"x":10.75, "y":0}, {"x":11.75, "y":0}, {"x":12.75, "y":0}, {"x":13.75, "y":0}, {"x":14.75, "y":0}, {"x":15.75, "y":0}, {"x":17, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":8.25, "y":1}, {"x":9.25, "y":1}, {"x":10.25, "y":1}, {"x":11.25, "y":1}, {"x":12.25, "y":1}, {"x":13.25, "y":1}, {"x":14.25, "y":1}, {"x":15.25, "y":1, "w":1.5}, {"x":17, "y":1}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":8.5, "y":2}, {"x":9.5, "y":2}, {"x":10.5, "y":2}, {"x":11.5, "y":2}, {"x":12.5, "y":2}, {"x":13.5, "y":2}, {"x":14.5, "y":2, "w":2.25}, {"x":17, "y":2}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":8, "y":3}, {"x":9, "y":3}, {"x":10, "y":3}, {"x":11, "y":3}, {"x":12, "y":3}, {"x":13, "y":3}, {"x":14, "y":3, "w":1.75}, {"x":16.25, "y":3.25}, {"x":0, "y":4, "w":1.5}, {"x":3, "y":4, "w":1.5}, {"x":4.5, "y":4, "w":2}, {"x":6.5, "y":4}, {"x":8, "y":4, "w":2.75}, {"x":10.75, "y":4, "w":1.5}, {"x":13.25, "y":4, "w":1.5}, {"x":15.25, "y":4.25}, {"x":16.25, "y":4.25}, {"x":17.25, "y":4.25}] + } + } +} \ No newline at end of file diff --git a/keyboards/wolfmarkclub/wm1/keymaps/default/keymap.c b/keyboards/wolfmarkclub/wm1/keymaps/default/keymap.c new file mode 100644 index 00000000000..83e9ac21a75 --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/keymaps/default/keymap.c @@ -0,0 +1,17 @@ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[0] = LAYOUT( +KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_GRV, KC_DEL, KC_HOME, +KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, KC_END, +KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, MO(1), +KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_UP, +KC_LCTL, KC_LALT,KC_LGUI,KC_SPC, KC_SPC, KC_RALT, KC_RCTL, KC_LEFT, KC_DOWN, KC_RIGHT), + +[1] = LAYOUT( +KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, _______, _______, _______, +RESET, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, +_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, +_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, +_______, _______, _______, _______, _______, _______, _______, _______, _______, _______), +}; \ No newline at end of file diff --git a/keyboards/wolfmarkclub/wm1/ld/wm1_f103.ld b/keyboards/wolfmarkclub/wm1/ld/wm1_f103.ld new file mode 100644 index 00000000000..41362282bc6 --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/ld/wm1_f103.ld @@ -0,0 +1,88 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/* + * STM32F103xC memory setup for use with the WM1 mass-storage device bootloader. + * You will have to change: + * OPT_DEFS = -DCORTEX_VTOR_INIT=0x10000 + * in your board's rules.mk + */ +MEMORY +{ + flash0 : org = 0x08010000, len = 256k - 0x10000 + flash1 : org = 0x00000000, len = 0 + flash2 : org = 0x00000000, len = 0 + flash3 : org = 0x00000000, len = 0 + flash4 : org = 0x00000000, len = 0 + flash5 : org = 0x00000000, len = 0 + flash6 : org = 0x00000000, len = 0 + flash7 : org = 0x00000000, len = 0 + ram0 : org = 0x20000000, len = 48k + ram1 : org = 0x00000000, len = 0 + ram2 : org = 0x00000000, len = 0 + ram3 : org = 0x00000000, len = 0 + ram4 : org = 0x00000000, len = 0 + ram5 : org = 0x00000000, len = 0 + ram6 : org = 0x00000000, len = 0 + ram7 : org = 0x00000000, len = 0 +} + +/* For each data/text section two region are defined, a virtual region + and a load region (_LMA suffix).*/ + +/* Flash region to be used for exception vectors.*/ +REGION_ALIAS("VECTORS_FLASH", flash0); +REGION_ALIAS("VECTORS_FLASH_LMA", flash0); + +/* Flash region to be used for constructors and destructors.*/ +REGION_ALIAS("XTORS_FLASH", flash0); +REGION_ALIAS("XTORS_FLASH_LMA", flash0); + +/* Flash region to be used for code text.*/ +REGION_ALIAS("TEXT_FLASH", flash0); +REGION_ALIAS("TEXT_FLASH_LMA", flash0); + +/* Flash region to be used for read only data.*/ +REGION_ALIAS("RODATA_FLASH", flash0); +REGION_ALIAS("RODATA_FLASH_LMA", flash0); + +/* Flash region to be used for various.*/ +REGION_ALIAS("VARIOUS_FLASH", flash0); +REGION_ALIAS("VARIOUS_FLASH_LMA", flash0); + +/* Flash region to be used for RAM(n) initialization data.*/ +REGION_ALIAS("RAM_INIT_FLASH_LMA", flash0); + +/* RAM region to be used for Main stack. This stack accommodates the processing + of all exceptions and interrupts.*/ +REGION_ALIAS("MAIN_STACK_RAM", ram0); + +/* RAM region to be used for the process stack. This is the stack used by + the main() function.*/ +REGION_ALIAS("PROCESS_STACK_RAM", ram0); + +/* RAM region to be used for data segment.*/ +REGION_ALIAS("DATA_RAM", ram0); +REGION_ALIAS("DATA_RAM_LMA", flash0); + +/* RAM region to be used for BSS segment.*/ +REGION_ALIAS("BSS_RAM", ram0); + +/* RAM region to be used for the default heap.*/ +REGION_ALIAS("HEAP_RAM", ram0); + +/* Generic rules inclusion.*/ +INCLUDE rules.ld diff --git a/keyboards/wolfmarkclub/wm1/mcuconf.h b/keyboards/wolfmarkclub/wm1/mcuconf.h new file mode 100644 index 00000000000..a645d3c5d5c --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/mcuconf.h @@ -0,0 +1,209 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef _MCUCONF_H_ +#define _MCUCONF_H_ + +#define STM32F103_MCUCONF + +/* + * STM32F103 drivers configuration. + * The following settings override the default settings present in + * the various device driver implementation headers. + * Note that the settings for each driver only have effect if the whole + * driver is enabled in halconf.h. + * + * IRQ priorities: + * 15...0 Lowest...Highest. + * + * DMA priorities: + * 0...3 Lowest...Highest. + */ + +/* + * HAL driver system settings. + */ +#define STM32_NO_INIT FALSE +#define STM32_HSI_ENABLED TRUE +#define STM32_LSI_ENABLED FALSE +#define STM32_HSE_ENABLED TRUE +#define STM32_LSE_ENABLED FALSE +#define STM32_SW STM32_SW_PLL +#define STM32_PLLSRC STM32_PLLSRC_HSE +#define STM32_PLLXTPRE STM32_PLLXTPRE_DIV1 +#define STM32_PLLMUL_VALUE 9 +#define STM32_HPRE STM32_HPRE_DIV1 +#define STM32_PPRE1 STM32_PPRE1_DIV2 +#define STM32_PPRE2 STM32_PPRE2_DIV2 +#define STM32_ADCPRE STM32_ADCPRE_DIV4 +#define STM32_USB_CLOCK_REQUIRED TRUE +#define STM32_USBPRE STM32_USBPRE_DIV1P5 +#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK +#define STM32_RTCSEL STM32_RTCSEL_HSEDIV +#define STM32_PVD_ENABLE FALSE +#define STM32_PLS STM32_PLS_LEV0 + +/* + * ADC driver system settings. + */ +#define STM32_ADC_USE_ADC1 FALSE +#define STM32_ADC_ADC1_DMA_PRIORITY 2 +#define STM32_ADC_ADC1_IRQ_PRIORITY 6 + +/* + * CAN driver system settings. + */ +#define STM32_CAN_USE_CAN1 FALSE +#define STM32_CAN_CAN1_IRQ_PRIORITY 11 + +/* + * EXT driver system settings. + */ +#define STM32_EXT_EXTI0_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI1_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI2_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI3_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI4_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI16_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI17_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI18_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI19_IRQ_PRIORITY 6 + +/* + * GPT driver system settings. + */ +#define STM32_GPT_USE_TIM1 FALSE +#define STM32_GPT_USE_TIM2 FALSE +#define STM32_GPT_USE_TIM3 FALSE +#define STM32_GPT_USE_TIM4 FALSE +#define STM32_GPT_USE_TIM5 FALSE +#define STM32_GPT_USE_TIM8 FALSE +#define STM32_GPT_TIM1_IRQ_PRIORITY 7 +#define STM32_GPT_TIM2_IRQ_PRIORITY 7 +#define STM32_GPT_TIM3_IRQ_PRIORITY 7 +#define STM32_GPT_TIM4_IRQ_PRIORITY 7 +#define STM32_GPT_TIM5_IRQ_PRIORITY 7 +#define STM32_GPT_TIM8_IRQ_PRIORITY 7 + +/* + * I2C driver system settings. + */ +#define STM32_I2C_USE_I2C1 FALSE +#define STM32_I2C_USE_I2C2 FALSE +#define STM32_I2C_BUSY_TIMEOUT 50 +#define STM32_I2C_I2C1_IRQ_PRIORITY 5 +#define STM32_I2C_I2C2_IRQ_PRIORITY 5 +#define STM32_I2C_I2C1_DMA_PRIORITY 3 +#define STM32_I2C_I2C2_DMA_PRIORITY 3 +#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure") + +/* + * ICU driver system settings. + */ +#define STM32_ICU_USE_TIM1 FALSE +#define STM32_ICU_USE_TIM2 FALSE +#define STM32_ICU_USE_TIM3 FALSE +#define STM32_ICU_USE_TIM4 FALSE +#define STM32_ICU_USE_TIM5 FALSE +#define STM32_ICU_USE_TIM8 FALSE +#define STM32_ICU_TIM1_IRQ_PRIORITY 7 +#define STM32_ICU_TIM2_IRQ_PRIORITY 7 +#define STM32_ICU_TIM3_IRQ_PRIORITY 7 +#define STM32_ICU_TIM4_IRQ_PRIORITY 7 +#define STM32_ICU_TIM5_IRQ_PRIORITY 7 +#define STM32_ICU_TIM8_IRQ_PRIORITY 7 + +/* + * PWM driver system settings. + */ +#define STM32_PWM_USE_ADVANCED FALSE +#define STM32_PWM_USE_TIM1 FALSE +#define STM32_PWM_USE_TIM2 TRUE +#define STM32_PWM_USE_TIM3 FALSE +#define STM32_PWM_USE_TIM4 FALSE +#define STM32_PWM_USE_TIM5 FALSE +#define STM32_PWM_USE_TIM8 FALSE +#define STM32_PWM_TIM1_IRQ_PRIORITY 7 +#define STM32_PWM_TIM2_IRQ_PRIORITY 7 +#define STM32_PWM_TIM3_IRQ_PRIORITY 7 +#define STM32_PWM_TIM4_IRQ_PRIORITY 7 +#define STM32_PWM_TIM5_IRQ_PRIORITY 7 +#define STM32_PWM_TIM8_IRQ_PRIORITY 7 + +/* + * RTC driver system settings. + */ +#define STM32_RTC_IRQ_PRIORITY 15 + +/* + * SERIAL driver system settings. + */ +#define STM32_SERIAL_USE_USART1 FALSE +#define STM32_SERIAL_USE_USART2 FALSE +#define STM32_SERIAL_USE_USART3 FALSE +#define STM32_SERIAL_USE_UART4 FALSE +#define STM32_SERIAL_USE_UART5 FALSE +#define STM32_SERIAL_USART1_PRIORITY 12 +#define STM32_SERIAL_USART2_PRIORITY 12 +#define STM32_SERIAL_USART3_PRIORITY 12 +#define STM32_SERIAL_UART4_PRIORITY 12 +#define STM32_SERIAL_UART5_PRIORITY 12 + +/* + * SPI driver system settings. + */ +#define STM32_SPI_USE_SPI1 FALSE +#define STM32_SPI_USE_SPI2 FALSE +#define STM32_SPI_USE_SPI3 FALSE +#define STM32_SPI_SPI1_DMA_PRIORITY 1 +#define STM32_SPI_SPI2_DMA_PRIORITY 1 +#define STM32_SPI_SPI3_DMA_PRIORITY 1 +#define STM32_SPI_SPI1_IRQ_PRIORITY 10 +#define STM32_SPI_SPI2_IRQ_PRIORITY 10 +#define STM32_SPI_SPI3_IRQ_PRIORITY 10 +#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure") + +/* + * ST driver system settings. + */ +#define STM32_ST_IRQ_PRIORITY 8 +#define STM32_ST_USE_TIMER 2 + +/* + * UART driver system settings. + */ +#define STM32_UART_USE_USART1 FALSE +#define STM32_UART_USE_USART2 FALSE +#define STM32_UART_USE_USART3 FALSE +#define STM32_UART_USART1_IRQ_PRIORITY 12 +#define STM32_UART_USART2_IRQ_PRIORITY 12 +#define STM32_UART_USART3_IRQ_PRIORITY 12 +#define STM32_UART_USART1_DMA_PRIORITY 0 +#define STM32_UART_USART2_DMA_PRIORITY 0 +#define STM32_UART_USART3_DMA_PRIORITY 0 +#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure") + +/* + * USB driver system settings. + */ +#define STM32_USB_USE_USB1 TRUE +#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE +#define STM32_USB_USB1_HP_IRQ_PRIORITY 13 +#define STM32_USB_USB1_LP_IRQ_PRIORITY 14 + +#endif /* _MCUCONF_H_ */ diff --git a/keyboards/wolfmarkclub/wm1/readme.md b/keyboards/wolfmarkclub/wm1/readme.md new file mode 100644 index 00000000000..74e92b2ee10 --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/readme.md @@ -0,0 +1,17 @@ +# Wolfmark Club WM1 + +![WM1](https://i.imgur.com/TDFp97yl.jpg) + +Split Ergo 65% keyboard + +* Keyboard Maintainer: [MechMerlin](https://github.com/mechmerlin) +* Hardware Supported: WM1 +* Hardware Availability: Available through China run Group Buy. + +Make example for this keyboard (after setting up your build environment): + + make wolfmarkclub/wm1:default + +**Reset Key**: Hold the `Esc` key while plugging in your cable, and the board will appear as a USB drive on your computer. + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/wolfmarkclub/wm1/rules.mk b/keyboards/wolfmarkclub/wm1/rules.mk new file mode 100644 index 00000000000..14ddab26d9d --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/rules.mk @@ -0,0 +1,33 @@ +# MCU name +MCU = STM32F103 + +# GENERIC STM32F103C8T6 board - mass storage bootloader +OPT_DEFS = -DCORTEX_VTOR_INIT=0x10000 +MCU_LDSCRIPT = wm1_f103 +BOARD = STM32_F103_STM32DUINO + +PROGRAM_CMD=echo 'CLI flashing not supported' >&2 + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = yes # Console for debug +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = yes # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +LTO_ENABLE = yes + +# Enter lower-power sleep mode when on the ChibiOS idle thread +OPT_DEFS += -DCORTEX_ENABLE_WFI_IDLE=TRUE diff --git a/keyboards/wolfmarkclub/wm1/wm1.c b/keyboards/wolfmarkclub/wm1/wm1.c new file mode 100644 index 00000000000..d199546f890 --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/wm1.c @@ -0,0 +1,17 @@ +#include "wm1.h" + +void matrix_init_kb(void) { + setPinOutput(B1); // Top Indicator LED + setPinOutput(B0); // Middle Indicator LED + setPinOutput(C5); // Bottom Indicator LED + matrix_init_user(); +} + +bool led_update_kb(led_t led_state) { + if(led_update_user(led_state)) { + writePin(B1, led_state.caps_lock); + writePin(B0, led_state.num_lock); + writePin(C5, led_state.scroll_lock); + } + return true; +} diff --git a/keyboards/wolfmarkclub/wm1/wm1.h b/keyboards/wolfmarkclub/wm1/wm1.h new file mode 100644 index 00000000000..1750b6366a5 --- /dev/null +++ b/keyboards/wolfmarkclub/wm1/wm1.h @@ -0,0 +1,34 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + */ + +#pragma once + +#include "quantum.h" + +#define LAYOUT( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K0E, K2D, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, K1E, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2E, \ + K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3E, \ + K40, K42, K43, K45, K47, K49, K4B, K4C, K4D, K4E \ +)\ +{\ + {K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K0E}, \ + {K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, K1E}, \ + {K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, K2E}, \ + {K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, KC_NO, K3E}, \ + {K40, KC_NO, K42, K43, KC_NO, K45, KC_NO, K47, KC_NO, K49, KC_NO, K4B, K4C, K4D, K4E } \ +}