Merge pull request #609 from sethbc/fix_clueboard_orphaned_files

remove orphaned clueboard files

keyboards/clueboard2/Makefile

@@ -1,71 +0,0 @@
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= no	# Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes	# Console for debug(+400)
-COMMAND_ENABLE ?= yes    # Commands for debug and configuration
-NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-RGBLIGHT_ENABLE ?= no   # Enable keyboard underlight functionality (+4870)
-BACKLIGHT_ENABLE ?= yes  # Enable keyboard backlight functionality (+1150)
-MIDI_ENABLE ?= no 		# MIDI controls
-AUDIO_ENABLE ?= no
-UNICODE_ENABLE ?= no 		# Unicode
-BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
-
-ifndef QUANTUM_DIR
-	include ../../Makefile
-endif

keyboards/clueboard2/clueboard2.c

@@ -1,63 +0,0 @@
-#include "clueboard2.h"
-
-void matrix_init_kb(void) {
-	// put your keyboard start-up code here
-	// runs once when the firmware starts up
-	matrix_init_user();
-	led_init_ports();
-
-    // JTAG disable for PORT F. write JTD bit twice within four cycles.
-    MCUCR |= (1<<JTD);
-    MCUCR |= (1<<JTD);
-};
-
-void led_init_ports() {
-    // * Set our LED pins as output
-    DDRB |= (1<<4);
-}
-
-void led_set_kb(uint8_t usb_led) {
-    if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
-        // Turn capslock on
-        PORTB |= (1<<4);
-    } else {
-        // Turn capslock off
-        PORTB &= ~(1<<4);
-    }
-}
-
-/* Clueboard 2.0 LED locations:
- *
- * Capslock: B4, pull high to turn on
- * LCtrl: Shared with Capslock, DO NOT INSTALL LED'S IN BOTH
- * Page Up: B7, pull high to turn on
- * Escape: D6, pull high to turn on
- * Arrows: D4, pull high to turn on
- */
-
-void backlight_init_ports(void) {
-    print("init_backlight_pin()\n");
-    // Set our LED pins as output
-    DDRD |= (1<<6); // Esc
-    DDRB |= (1<<7); // Page Up
-    DDRD |= (1<<4); // Arrows
-
-    // Set our LED pins low
-    PORTD &= ~(1<<6); // Esc
-    PORTB &= ~(1<<7); // Page Up
-    PORTD &= ~(1<<4); // Arrows
-}
-
-void backlight_set(uint8_t level) {
-    if ( level == 0 ) {
-        // Turn off light
-        PORTD |= (1<<6); // Esc
-        PORTB |= (1<<7); // Page Up
-        PORTD |= (1<<4); // Arrows
-    } else {
-        // Turn on light
-        PORTD &= ~(1<<6); // Esc
-        PORTB &= ~(1<<7); // Page Up
-        PORTD &= ~(1<<4); // Arrows
-    }
-}