@ -1,75 +1,3 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= no # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 | |||
ifndef QUANTUM_DIR | |||
ifndef MAKEFILE_INCLUDED | |||
include ../../Makefile | |||
endif | |||
endif |
@ -0,0 +1,67 @@ | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE ?= no # USB Nkey Rollover | |||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE ?= no # MIDI controls | |||
UNICODE_ENABLE ?= no # Unicode | |||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE ?= no # Audio output on port C6 |