@ -0,0 +1,56 @@ | |||
#ifndef CONFIG_H | |||
#define CONFIG_H | |||
#include "config_common.h" | |||
/* USB Device descriptor parameter */ | |||
#define VENDOR_ID 0xFEED | |||
#define PRODUCT_ID 0x6060 | |||
#define DEVICE_VER 0x0001 | |||
#define MANUFACTURER Unikeyboard | |||
#define PRODUCT Felix | |||
#define DESCRIPTION 4x5 number/macropad. | |||
/* key matrix size */ | |||
#define MATRIX_ROWS 5 | |||
#define MATRIX_COLS 4 | |||
/* key matrix pins */ | |||
#define MATRIX_ROW_PINS { B2, B3, B1, F7, F6 } | |||
#define MATRIX_COL_PINS { B5, B4, E6, D7 } | |||
#define UNUSED_PINS | |||
/* COL2ROW or ROW2COL */ | |||
#define DIODE_DIRECTION ROW2COL | |||
/* number of backlight levels */ | |||
/* Not sure what pin controls the backlighting, need help for this. */ | |||
#define BACKLIGHT_PIN | |||
#define BACKLIGHT_LEVELS 5 | |||
/* Set 0 if debouncing isn't needed */ | |||
#define DEBOUNCING_DELAY 5 | |||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ | |||
#define LOCKING_SUPPORT_ENABLE | |||
/* Locking resynchronize hack */ | |||
#define LOCKING_RESYNC_ENABLE | |||
/* key combination for command */ | |||
#define IS_COMMAND() ( \ | |||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ | |||
) | |||
/* prevent stuck modifiers */ | |||
#define PREVENT_STUCK_MODIFIERS | |||
/* there is no rgb underglow by default. */ | |||
#define RGB_DI_PIN | |||
#define RGBLIGHT_ANIMATIONS | |||
#define RGBLED_NUM 16 | |||
#define RGBLIGHT_HUE_STEP 8 | |||
#define RGBLIGHT_SAT_STEP 8 | |||
#define RGBLIGHT_VAL_STEP 8 | |||
#endif |
@ -0,0 +1 @@ | |||
#include "felix.h" |
@ -0,0 +1,20 @@ | |||
#ifndef FELIX_H | |||
#define FELIX_H | |||
#include "quantum.h" | |||
#define KEYMAP( \ | |||
K000, K001, K002, K003, \ | |||
K100, K101, K102, K103, \ | |||
K200, K201, K202, K203, \ | |||
K300, K301, K302, K303, \ | |||
K400, K401, K402, K403 \ | |||
) { \ | |||
{ K000, K001, K002, K003 }, \ | |||
{ K100, K101, K102, K103 }, \ | |||
{ K200, K201, K202, K203 }, \ | |||
{ K300, K301, K302, K303 }, \ | |||
{ K400, K401, K402, K403 } \ | |||
} | |||
#endif |
@ -0,0 +1,22 @@ | |||
#include "felix.h" | |||
#include "action_layer.h" | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
KEYMAP( | |||
KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, | |||
KC_P7, KC_P8, KC_P9, KC_PPLS, | |||
KC_P4, KC_P5, KC_P6, KC_HOME, | |||
KC_P1, KC_P2, KC_P3, KC_END, | |||
KC_P0, KC_PEQL, KC_PDOT, KC_PENT), | |||
}; | |||
void persistant_default_layer_set(uint16_t default_layer) { | |||
} | |||
bool process_record_user(uint16_t keycode, keyrecord_t *record) { | |||
switch (keycode) { | |||
} | |||
return true; | |||
} |
@ -0,0 +1,13 @@ | |||
# Felix | |||
A customizable number/macropad made by Unikeyboard. | |||
Keyboard Maintainer: [QMK Community](https://github.com/qmk) | |||
Hardware Supported: Felix PCB, Pro Micro | |||
Hardware Availability: [Unikeyboard](https://unikeyboard.io/product/felix/) | |||
Make example for this keyboard (after setting up your build environment): | |||
make felix-default | |||
See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information. |
@ -0,0 +1,56 @@ | |||
# MCU name | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = no # Console for debug(+400) | |||
COMMAND_ENABLE = no # Commands for debug and configuration | |||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |||
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality | |||
AUDIO_ENABLE = no | |||
RGBLIGHT_ENABLE = no |