diff --git a/keyboards/minorca/Makefile b/keyboards/minorca/Makefile
new file mode 100644
index 00000000000..8cff0004935
--- /dev/null
+++ b/keyboards/minorca/Makefile
@@ -0,0 +1,71 @@
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no         # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+NKRO_ENABLE ?= yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality
+MIDI_ENABLE ?= no            # MIDI controls
+AUDIO_ENABLE ?= no           # Audio output on port C6
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE ?= yes       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+	include ../../Makefile
+endif
\ No newline at end of file
diff --git a/keyboards/minorca/config.h b/keyboards/minorca/config.h
new file mode 100644
index 00000000000..4cdafcbd2e4
--- /dev/null
+++ b/keyboards/minorca/config.h
@@ -0,0 +1,80 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6660
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    ME
+#define PRODUCT         MinOrca
+#define DESCRIPTION     Tiny Whale
+
+/* key matrix size */
+#define MATRIX_ROWS 4
+#define MATRIX_COLS 12
+
+/* MinOrca PCB default pin-out */
+#define MATRIX_COL_PINS { D4, D6, D7, B4, B5, B6, F7, F6, F5, F4, F1, F0 }
+#define MATRIX_ROW_PINS { B0, B1, B2, B3 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* define if matrix has ghost */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+#define BACKLIGHT_LEVELS 3
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
diff --git a/keyboards/minorca/keymaps/default/Makefile b/keyboards/minorca/keymaps/default/Makefile
new file mode 100644
index 00000000000..8dc851fddf1
--- /dev/null
+++ b/keyboards/minorca/keymaps/default/Makefile
@@ -0,0 +1,25 @@
+
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif
diff --git a/keyboards/minorca/keymaps/default/config.h b/keyboards/minorca/keymaps/default/config.h
new file mode 100644
index 00000000000..bf40376c19b
--- /dev/null
+++ b/keyboards/minorca/keymaps/default/config.h
@@ -0,0 +1,12 @@
+#ifndef CONFIG_USER_H
+#define CONFIG_USER_H
+
+#include "../../config.h"
+
+/* bootmagic salt key */
+#define BOOTMAGIC_KEY_SALT              KC_ESC
+
+/* skip bootmagic and eeconfig */
+#define BOOTMAGIC_KEY_SKIP              KC_SPACE
+
+#endif
diff --git a/keyboards/minorca/keymaps/default/keymap.c b/keyboards/minorca/keymaps/default/keymap.c
new file mode 100644
index 00000000000..a55d578e449
--- /dev/null
+++ b/keyboards/minorca/keymaps/default/keymap.c
@@ -0,0 +1,44 @@
+// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
+// this is the style you want to emulate.
+
+#include "minorca.h"
+#include "action_layer.h"
+#include "eeconfig.h"
+
+extern keymap_config_t keymap_config;
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+
+// Fillers to make layering more clear
+#define _______ KC_TRNS
+#define XXXXXXX KC_NO
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    [0] = { /* Base */
+        {KC_ESC,  KC_Q,    KC_W,     KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC },
+        {KC_TAB,  KC_A,    KC_S,     KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    XXXXXXX, KC_ENT  },
+        {KC_LCTRL,XXXXXXX, KC_Z,     KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_QUOT, KC_FN1,  KC_FN0 },
+        {KC_NO,   XXXXXXX, KC_NO,    KC_LALT, KC_SPC,  XXXXXXX, XXXXXXX, KC_SPC,  XXXXXXX, KC_DOT,  KC_SLSH, KC_NO }
+    },
+    [1] = { /* First */
+        {KC_GRV,  KC_1,    KC_2,     KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_DELT },
+        {KC_TAB,  KC_MPRV, KC_MPLY,  KC_MNXT, KC_PGUP, KC_HOME, KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, XXXXXXX, KC_LGUI  },
+        {KC_LCTRL,XXXXXXX, KC_Z,     KC_X,    KC_C,    KC_PGDN, KC_END,  KC_L,    KC_SCLN, KC_UP,   KC_FN1,  KC_FN0 },
+        {KC_NO,   XXXXXXX, KC_NO,    KC_LALT, _______, XXXXXXX, XXXXXXX, _______, XXXXXXX, KC_DOWN, KC_RIGHT,KC_NO }
+    },
+    [2] = { /* Second */
+        {KC_ESC,  KC_EXLM, KC_AT,    KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DELT },
+        {KC_TAB,  KC_MUTE, KC_VOLD,  KC_VOLU, KC_TILD, KC_PIPE, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, XXXXXXX, KC_ENT  },
+        {KC_CAPS, XXXXXXX, KC_LSFT,  KC_RSFT, KC_PAUSE,KC_F10,  KC_F11,  KC_F12,  KC_NO,   KC_UP,   KC_FN1,  KC_FN0 },
+        {KC_NO,   XXXXXXX, KC_NO,    KC_LALT, _______, XXXXXXX, XXXXXXX, _______, XXXXXXX, KC_DOWN, KC_RIGHT,KC_NO }
+    },
+}; 
+ 
+const uint16_t PROGMEM fn_actions[] = {
+	    [0] = ACTION_LAYER_MOMENTARY(1),  // to First overlay
+	    [1] = ACTION_LAYER_MOMENTARY(2),  // to Second overlay
+
+};
\ No newline at end of file
diff --git a/keyboards/minorca/keymaps/default/readme.md b/keyboards/minorca/keymaps/default/readme.md
new file mode 100644
index 00000000000..6ed31f82b36
--- /dev/null
+++ b/keyboards/minorca/keymaps/default/readme.md
@@ -0,0 +1,5 @@
+# The Default Minorca Layout
+
+Copied from https://github.com/pancinteractive/qmk_firmware/blob/master/keyboard/minorca_mkV/keymaps/default/keymap.c
+
+It looks incomplete.
\ No newline at end of file
diff --git a/keyboards/minorca/keymaps/readme.md b/keyboards/minorca/keymaps/readme.md
new file mode 100644
index 00000000000..54fb5f6d9e0
--- /dev/null
+++ b/keyboards/minorca/keymaps/readme.md
@@ -0,0 +1,23 @@
+# How to add your own keymap
+
+Folders can be named however you'd like (will be approved upon merging), or should follow the format with a preceding `_`:
+
+    _[ISO 3166-1 alpha-2 code*]_[layout variant]_[layout name/author]
+
+\* See full list: https://en.wikipedia.org/wiki/ISO_3166-1#Officially_assigned_code_elements
+
+and contain the following files:
+
+* `keymap.c`
+* `readme.md` *recommended*
+* `config.h` *optional*, found automatically when compiling
+* `Makefile` *optional*, found automatically when compling
+
+When adding your keymap to this list, keep it organised alphabetically (select list, edit->sort lines), and use this format:
+
+     * **folder_name** description
+
+# List of Planck keymaps
+
+* **default** default Planck layout
+* **cbbrowne** cbbrowne's Planck layout
\ No newline at end of file
diff --git a/keyboards/minorca/keymaps/rgb/Makefile b/keyboards/minorca/keymaps/rgb/Makefile
new file mode 100644
index 00000000000..230f75a628f
--- /dev/null
+++ b/keyboards/minorca/keymaps/rgb/Makefile
@@ -0,0 +1,25 @@
+
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = yes       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif
diff --git a/keyboards/minorca/keymaps/rgb/config.h b/keyboards/minorca/keymaps/rgb/config.h
new file mode 100644
index 00000000000..deaac2e26fa
--- /dev/null
+++ b/keyboards/minorca/keymaps/rgb/config.h
@@ -0,0 +1,20 @@
+#ifndef CONFIG_USER_H
+#define CONFIG_USER_H
+
+#include "../../config.h"
+
+/* bootmagic salt key */
+#define BOOTMAGIC_KEY_SALT              KC_ESC
+
+/* skip bootmagic and eeconfig */
+#define BOOTMAGIC_KEY_SKIP              KC_SPACE
+
+/* ws2812 RGB LED */
+#define RGB_DI_PIN D5
+#define RGBLIGHT_TIMER
+#define RGBLED_NUM 13     // Number of LEDs
+#define RGBLIGHT_HUE_STEP 10
+#define RGBLIGHT_SAT_STEP 17
+#define RGBLIGHT_VAL_STEP 17
+
+#endif
diff --git a/keyboards/minorca/keymaps/rgb/example.jpg b/keyboards/minorca/keymaps/rgb/example.jpg
new file mode 100644
index 00000000000..a04c8d37d6c
Binary files /dev/null and b/keyboards/minorca/keymaps/rgb/example.jpg differ
diff --git a/keyboards/minorca/keymaps/rgb/keymap.c b/keyboards/minorca/keymaps/rgb/keymap.c
new file mode 100644
index 00000000000..9002afbb889
--- /dev/null
+++ b/keyboards/minorca/keymaps/rgb/keymap.c
@@ -0,0 +1,65 @@
+// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
+// this is the style you want to emulate.
+
+#include "minorca.h"
+#include "action_layer.h"
+#include "eeconfig.h"
+
+extern keymap_config_t keymap_config;
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _QWERTY 0
+#define _LOWER 1
+#define _RAISE 2
+#define _TB 3
+
+// Macro name shortcuts
+#define QWERTY M(_QWERTY)
+#define LOWER M(_LOWER)
+#define RAISE M(_RAISE)
+
+// Fillers to make layering more clear
+#define _______ KC_TRNS
+#define XXXXXXX KC_NO
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+[_QWERTY] = { /* Qwerty */
+  {KC_ESC,     KC_Q,       KC_W,       KC_E,       KC_R,     KC_T,    KC_Y,     KC_U,       KC_I,       KC_O,       KC_P,       KC_BSPC},
+  {FUNC(0),    KC_A,       KC_S,       KC_D,       KC_F,     KC_G,    KC_H,     KC_J,       KC_K,       KC_L,       XXXXXXX,    KC_QUOT},
+  {KC_LSFT,    XXXXXXX,    KC_Z,       KC_X,       KC_C,     KC_V,    KC_B,     KC_N,       KC_M,       KC_COMM,    KC_DOT,     FUNC(1)},
+  {KC_LCTL,    XXXXXXX,    KC_LGUI,    KC_LALT,    FUNC(2),  XXXXXXX, XXXXXXX,  FUNC(3),    XXXXXXX,    KC_RALT,    KC_APP,     KC_RCTL}
+},
+
+[_RAISE] = {
+  {S(KC_GRV),  S(KC_1),    S(KC_2),    S(KC_3),    S(KC_4),  S(KC_5), S(KC_6),  S(KC_7),    S(KC_8),    S(KC_9),    S(KC_0),    KC_BSPC},
+  {KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_PAUSE,   KC_TRNS,  KC_TRNS, KC_TRNS,  S(KC_MINS), S(KC_EQL),  S(KC_LBRC), XXXXXXX,    S(KC_BSLS)},
+  {KC_TRNS,    XXXXXXX,    KC_F1,      KC_F2,      KC_F3,    KC_F4,   KC_F5,    KC_F6,      KC_F7,      KC_F8,      KC_F9,      KC_ENT},
+  {KC_TRNS,    XXXXXXX,    KC_TRNS,    KC_TRNS,    KC_TRNS,  XXXXXXX, XXXXXXX,  KC_TRNS,    XXXXXXX,    KC_MNXT,    KC_MUTE,    KC_MPLY}
+},
+
+[_LOWER] = {
+  {KC_GRV,     KC_1,       KC_2,       KC_3,       KC_4,     KC_5,    KC_6,     KC_7,       KC_8,       KC_9,       KC_0,       KC_DELETE},
+  {KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,  KC_TRNS, KC_TRNS,  KC_MINS,    KC_EQL,     KC_LBRC,    XXXXXXX,    KC_BSLS},
+  {KC_TRNS,    XXXXXXX,    KC_F11,     KC_F12,     KC_F13,   KC_F14,  KC_F15,   KC_F16,     KC_F17,     KC_F18,     KC_PGUP,    KC_ENT},
+  {KC_TRNS,    XXXXXXX,    KC_TRNS,    KC_TRNS,    KC_TRNS,  XXXXXXX, XXXXXXX,  KC_TRNS,    XXXXXXX,    KC_HOME,    KC_PGDN,    KC_END}
+},
+
+[_TB] = { /* Tab */
+  {KC_ESC,     KC_CALC,    KC_WHOM,    KC_MAIL,    KC_MYCM,  KC_TRNS, KC_TRNS,  KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_PSCR,    KC_TRNS},
+  {KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS,    KC_TRNS,    KC_TRNS,    XXXXXXX,    KC_TRNS},
+  {KC_TRNS,    XXXXXXX,    RGB_TOG,    RGB_MOD,    RGB_HUI,  RGB_HUD, RGB_SAI,  RGB_SAD,    RGB_VAI,    RGB_VAD,    KC_UP,      KC_ENT},
+  {BL_STEP,    XXXXXXX,    KC_TRNS,    KC_TRNS,    KC_TRNS,  XXXXXXX, XXXXXXX,  KC_TRNS,    XXXXXXX,    KC_LEFT,    KC_DOWN,    KC_RGHT}
+}
+};
+
+
+const uint16_t PROGMEM fn_actions[] = {
+  [0]  = ACTION_LAYER_TAP_KEY(_TB, KC_TAB),
+  [1]  = ACTION_MODS_TAP_KEY(MOD_RSFT, KC_ENT),
+  [2]  = ACTION_LAYER_TAP_KEY(_RAISE, KC_SPC),
+  [3]  = ACTION_LAYER_TAP_KEY(_LOWER, KC_SPC),
+};
diff --git a/keyboards/minorca/keymaps/rgb/readme.md b/keyboards/minorca/keymaps/rgb/readme.md
new file mode 100644
index 00000000000..50806068ceb
--- /dev/null
+++ b/keyboards/minorca/keymaps/rgb/readme.md
@@ -0,0 +1,23 @@
+#RGB backlight for MinOrca
+
+![wiring](example.jpg)
+
+Exmaple of adding WS2812b LEDs to a MinOrca.
+
+http://www.40percent.club/2016/08/tiny-whale.html
+
+The keymap is a work in progress. The RGB functions are accessed by holding down the TAB key. 
+
+Tab + Z		Toggle on/off
+Tab + X		Mode
+Tab + C		Hue+
+Tab + V		Hue-
+Tab + B		Saturation+
+Tab + N		Saturation-
+Tab + M		Brightness+
+Tab + ,		Brightness-
+
+Example wiring:
+
+![wiring](wiring1.jpg)
+![wiring closeup](wiring2.jpg)
diff --git a/keyboards/minorca/keymaps/rgb/wiring1.jpg b/keyboards/minorca/keymaps/rgb/wiring1.jpg
new file mode 100644
index 00000000000..7dcbe80c5ed
Binary files /dev/null and b/keyboards/minorca/keymaps/rgb/wiring1.jpg differ
diff --git a/keyboards/minorca/keymaps/rgb/wiring2.jpg b/keyboards/minorca/keymaps/rgb/wiring2.jpg
new file mode 100644
index 00000000000..fd91d3e1c96
Binary files /dev/null and b/keyboards/minorca/keymaps/rgb/wiring2.jpg differ
diff --git a/keyboards/minorca/minorca.c b/keyboards/minorca/minorca.c
new file mode 100644
index 00000000000..24e72c2a5c0
--- /dev/null
+++ b/keyboards/minorca/minorca.c
@@ -0,0 +1,6 @@
+#include "minorca.h"
+
+void matrix_init_kb(void) {
+
+	matrix_init_user();
+}
\ No newline at end of file
diff --git a/keyboards/minorca/minorca.h b/keyboards/minorca/minorca.h
new file mode 100644
index 00000000000..158e5b4c55b
--- /dev/null
+++ b/keyboards/minorca/minorca.h
@@ -0,0 +1,6 @@
+#ifndef MINORCA_H
+#define MINORCA_H
+
+#include "quantum.h"
+
+#endif
diff --git a/keyboards/minorca/readme.md b/keyboards/minorca/readme.md
new file mode 100644
index 00000000000..1d655dfe482
--- /dev/null
+++ b/keyboards/minorca/readme.md
@@ -0,0 +1,31 @@
+minorca keyboard firmware
+======================
+Handwired 40% keyboard
+
+## Quantum MK Firmware
+
+For the full Quantum feature list, see [the parent readme.md](/readme.md).
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboards/planck folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use `make dfu` to program your PCB once you hit the reset button. 
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files.
+
+To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
+```
+$ make KEYMAP=[default|jack|<name>]
+```
+Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
+
+### Notable forks (which some of the keymap files are from)
+- [Shane's Fork](https://github.com/shanecelis/tmk_keyboard/tree/master/keyboard/planck)
+- [Pierre's Fork](https://github.com/pcarrier/tmk_keyboard/blob/pcarrier/planck/keyboard/gh60/keymap_planck.c)
+- [Nathan's Fork](https://github.com/nathanrosspowell/tmk_keyboard/tree/planck-jack/keyboard/planck)
+- [Matthew's Fork](https://github.com/pepers/tmk_keyboard/tree/master/keyboard/planck_grid)