* **Bootmagic reset**: Hold down the top left key of the keyboard (top right or bottom left in horizontal configuration)
* **Physical reset**: Briefly press the button on the bottom of the microcontroller or, if not present short the pin marked RST to a GND.
* **Keycode in layout**: Press the key mapped to `RESET` if it is available
* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
* **Bootmagic reset**: Hold down the top left key on the left half (or the top right right key on the right half) and plug in the controller on that side.
* **Physical reset pins**: Briefly short the RST and GND pins on the microcontroller using tweezers, a paperclip, or any other conductive material.
* **Keycode in layout**: Press the key mapped to `RESET` if it is configured.
* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is configured.
* **Bootmagic reset**: Hold down the key at (0,0) in the matrix (usually the top left key or Escape) and plug in the keyboard
* **Physical reset button**: Briefly press the button on the front of the Elite-C microcontroller _**before soldering**_ it to the PCB- some may have pads you must short instead
* **Keycode in layout**: Press the key mapped to `RESET` if it is available
* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available
@ -17,4 +17,4 @@ See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_to
Enter the bootloader in 2 ways:
* Physical reset button: Briefly press the button on the back of the PCB - or short reset and ground pins
* Keycode in layout: Press the key mapped to `RESET`. By default this is done by pressing RALT to access second layer and pressing rotary encoder down.
* Keycode in layout: Press the key mapped to `QK_BOOT`. By default this is done by pressing RALT to access second layer and pressing rotary encoder down.
@ -17,7 +17,7 @@ Make example for this keyboard (after setting up your build environment):
Enter the bootloader in 2 ways:
* **Bootmagic reset**: Hold down the key at (0,0) in the matrix
* **Keycode in layout**: Press the key mapped to `RESET` if it is available
* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available
* **Physical reset pins**: Briefly short the reset pins using tweezers, a paperclip, or any other conductive material.
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
@ -18,6 +18,6 @@ Flashing example for this keyboard:
Enter the bootloader in 2 ways:
* **Physical reset button**: Briefly press the button on the back of the PCB - some may have pads you must short instead
* **Keycode in layout**: Press the key mapped to `RESET` if it is available
* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
@ -19,7 +19,7 @@ Flashing example for this keyboard:
## Bootloader
Enter the bootloader in 3 ways:
* **Physical reset button**: Briefly short the pad connected to RESET and GND on the back
* **Keycode in layout**: Press the key mapped to `RESET`, this is the recommened method
* **Physical reset button**: Briefly short the pad connected to QK_BOOT and GND on the back
* **Keycode in layout**: Press the key mapped to `QK_BOOT`, this is the recommened method
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
* **Bootmagic reset**: Hold down the key at (0,0) in the matrix (usually the top left key or Escape) and plug in the keyboard
* **Physical reset button**: Briefly press the button on the back of the PCB - some may have pads you must short instead
* **Keycode in layout**: Press the key mapped to `RESET` if it is available
* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
* **Bootmagic reset**: Hold down Escape and plug in the keyboard.
* **Physical reset button**: Briefly press the reset button below the pro-micro.
* **Keycode in layout**: The `RESET` key can be found by holding `FUNC` in between the space bars and pressing `ESC`.
* **Keycode in layout**: The `QK_BOOT` key can be found by holding `FUNC` in between the space bars and pressing `ESC`.
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
@ -139,7 +139,7 @@ This layer is not currently working but has been left as an example of how to wr
```
/* ADMIN
* ,-----------------------------------------.
* | RESET | | | X |
* | QK_BOOT | | | X |
* |------------+-----+-----------+----------|
* |ABOUT CKEYS | | | |
* |------------+-----+-----------+----------|
@ -150,7 +150,7 @@ This layer is not currently working but has been left as an example of how to wr
*/
```
The most important key in this layer is the `RESET` switch. Use it to flash new firmware. It does the same thing as the hardware button on the Proton C. But since you soldered the Proton C with the reset button facing towards the keys, the only way to reach it is to de-solder wires. The reset switch solves this. Program a reset switch into all of your future keyboards.
The most important key in this layer is the `QK_BOOT` switch. Use it to flash new firmware. It does the same thing as the hardware button on the Proton C. But since you soldered the Proton C with the reset button facing towards the keys, the only way to reach it is to de-solder wires. The reset switch solves this. Program a reset switch into all of your future keyboards.
The `ABOUT CKEYS` is another example of using a macro. It will type out a few sentences about cKeys.
@ -18,5 +18,5 @@ See [build environment setup](https://docs.qmk.fm/build_environment_setup.html)
#### Developer's Note
STM32F042xx chips does not allow jumping to bootloader without BOOT0 being set to high, therefore it is impossible to enter the bootloader from sending a `RESET` keycode nor using bootmagic or bootmagic lite.
The only way to enter bootloader is to hold the BOOT0 button while the keyboard is powering up or after a power reset (done by pressing the reset switch or sending a `RESET` keycode).
STM32F042xx chips does not allow jumping to bootloader without BOOT0 being set to high, therefore it is impossible to enter the bootloader from sending a `QK_BOOT` keycode nor using bootmagic or bootmagic lite.
The only way to enter bootloader is to hold the BOOT0 button while the keyboard is powering up or after a power reset (done by pressing the reset switch or sending a `QK_BOOT` keycode).
@ -18,5 +18,5 @@ See [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools)
#### Developer's Note
STM32F042xx chips does not allow jumping to bootloader without BOOT0 being set to high, therefore it is impossible to enter the bootloader from sending a `RESET` keycode nor using bootmagic or bootmagic lite.
The only way to enter bootloader is to hold the BOOT0 button while the keyboard is powering up or after a power reset (done by pressing the reset switch or sending a `RESET` keycode).
STM32F042xx chips does not allow jumping to bootloader without BOOT0 being set to high, therefore it is impossible to enter the bootloader from sending a `QK_BOOT` keycode nor using bootmagic or bootmagic lite.
The only way to enter bootloader is to hold the BOOT0 button while the keyboard is powering up or after a power reset (done by pressing the reset switch or sending a `QK_BOOT` keycode).
* **Bootmagic reset**: Hold down the key at (0,0) in the matrix (usually the top left key or Escape) and plug in the keyboard
* **Physical reset button**: Briefly press the button on the back of the PCB
* **Keycode in layout**: Press the key mapped to `RESET` if it is available
* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
* **Bootmagic reset**: Hold down the key at (0,0) in the matrix
* **Physical reset button**: hold the button on the back of the PCB during plug in cable.
* **Keycode in layout**: Press the key mapped to `RESET` if it is available
* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
@ -23,5 +23,5 @@ See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_to
Enter the bootloader in 3 ways:
* **Bootmagic reset**: Hold down the key at (0,1) in the matrix (the top left key or Escape) and plug in the keyboard
* **Keycode in layout**: Press the key mapped to `RESET` if it is available (activated by holding the lower right key and tapping the lower left key)
* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available (activated by holding the lower right key and tapping the lower left key)
* **Physical reset button**: Briefly sort the pads labeled "RST" and "GND" on the micro-controller
@ -16,6 +16,6 @@ Flashing example for this keyboard:
make eyeohdesigns/babyv:default:flash
To enter the bootloader, either depress the reset button on the back of the PCB, or use the 'RESET' keycode found on the function layer.
To enter the bootloader, either depress the reset button on the back of the PCB, or use the `QK_BOOT` keycode found on the function layer.
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
@ -16,6 +16,6 @@ Flashing example for this keyboard:
make eyeohdesigns/sprh:default:flash
To enter the bootloader, either depress the reset button on the back of the PCB, or use the 'RESET' keycode found on the function layer.
To enter the bootloader, either depress the reset button on the back of the PCB, or use the `QK_BOOT` keycode found on the function layer.
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
@ -16,6 +16,6 @@ Flashing example for this keyboard:
make eyeohdesigns/theboulevard:default:flash
To enter the bootloader, either depress the reset button on the back of the PCB, or use the 'RESET' keycode found on the function layer.
To enter the bootloader, either depress the reset button on the back of the PCB, or use the `QK_BOOT` keycode found on the function layer.
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).