* Fix issues with user split transport code
* Improve OLED (More font stuff, improved keylogger, etc)
* Add `KEYLOCK` macro to disable USB, borrowed from command feature.
* Convert Kyria fully to proton C (no more AVR kyria)
* Add Work Louder Work Board keymap

* Add Per Key functionality for AutoShift (#11536)

* LED Matrix: Reactive effect buffers & advanced indicators (#12588)

* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)

* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)

* LED Matrix: Split (#12633)

* [CI] Format code according to conventions (#12650)

* feat: infinite timeout for leader key (#6580)

* feat: implement leader_no_timeout logic

* docs(leader_key): infinite leader timeout docs

* Format code according to conventions (#12680)

* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)

* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)

Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1).  Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).

* Update ADC docs to match the actually used resolution

ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly.  Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).

* Fix pinToMux() for B12 and B13 on STM32F3xx

Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.

* Add support for all possible analog pins on STM32F1xx

Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families).  Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).

Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.

* Add support for all possible analog pins on STM32F4xx

Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled).  These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.

Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.

Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.

* Fix STM32F3xx ADC mux table in documentation

The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).

* Add STM32F1xx ADC pins to the documentation

* Add STM32F4xx ADC pins to the documentation

* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)

* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.

* Update flashing.md

* Update chconf.h

* Update config.h

* Update halconf.h

* Update mcuconf.h

* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)

* Add support for MCU = STM32F446 (#12619)

* Add support for MCU = STM32F446

* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h

* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64

* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.

* Format code according to conventions (#12682)

* Format code according to conventions (#12687)

* Add STM32L433 and L443 support (#12063)

* initial L433 commit

* change to XC

* fix L433

* disable all peripherals

* update system and peripheral clocks

* 433 change

* use its own board  files

* revert its own board files

* l433 specific change

* fix stm32l432xx define

* remove duplicate #define

* fix bootloader jump

* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h

* move to L443

* move to L443

* fix sdmmc in mcuconf.h

* include STM32L443

* add L443

* Include L443 in compatible microcontrollers

* Include L443 in compatible microcontrollers

* Update config bootloader jump description

* Update ChibiOS define reasoning

* Update quantum/mcu_selection.mk

* fix git conflict

* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)

* Fix bad PR merge for #6580. (#12721)

* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)

* [CI] Format code according to conventions (#12731)

* Fixing transport's led/rgb matrix suspend state logic (#12770)

* [CI] Format code according to conventions (#12772)

* Fix comment parsing (#12750)

* Added OLED fade out support (#12086)

* fix some references to bin/qmk that slipped in (#12832)

* Resolve a number of warnings in `qmk generate-api` (#12833)

* New command: qmk console (#12828)

* stash poc

* stash

* tidy up implementation

* Tidy up slightly for review

* Tidy up slightly for review

* Bodge environment to make tests pass

* Refactor away from asyncio due to windows issues

* Filter devices

* align vid/pid printing

* Add hidapi to the installers

* start preparing for multiple hid_listeners

* udev rules for hid_listen

* refactor to move closer to end state

* very basic implementation of the threaded model

* refactor how vid/pid/index are supplied and parsed

* windows improvements

* read the report directly when usage page isn't available

* add per-device colors, the choice to show names or numbers, and refactor

* add timestamps

* Add support for showing bootloaders

* tweak the color for bootloaders

* Align bootloader disconnect with connect color

* add support for showing all bootloaders

* fix the pyusb check

* tweaks

* fix exception

* hide a stack trace behind -v

* add --no-bootloaders option

* add documentation for qmk console

* Apply suggestions from code review

* pyformat

* clean up and flesh out KNOWN_BOOTLOADERS

* Remove pointless SERIAL_LINK_ENABLE rules (#12846)

* Make Swap Hands use PROGMEM (#12284)

This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.

* Fix another bin/qmk reference (#12856)

* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)

* Fixup build errors on `develop` branch. (#12723)

* LED Matrix: Effects! (#12651)

* Fix syntax error when compiling for ARM (#12866)

* Remove KEYMAP and LAYOUT_kc (#12160)

* alias KEYMAP to LAYOUT

* remove KEYMAP and LAYOUT_kc

* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)

* Rename `point_t` -> `led_point_t` (#12864)

* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)

* Add missing LED Matrix suspend code to suspend.c (#12878)

* LED Matrix: Documentation (#12685)

* Deprecate `send_unicode_hex_string()` (#12602)

* Fix spelling mistake regarding LED Matrix in split_common. (#12888)

* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)

* Use milc.subcommand.config instead of qmk.cli.config (#12915)

* Use milc.subcommand.config instead

* pyformat

* remove the config test

* Add function to allow repeated blinking of one layer (#12237)

* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time

* Update doc

* Rework rgblight blinking according to requested change

* optimize storage

* Fixup housekeeping from being invoked twice per loop. (#12933)

* matrix: wait for row signal to go HIGH for every row (#12945)

I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/

Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.

After this commit, all keyboard matrix rows are interpreted correctly.

I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.

* ensure we do not conflict with existing keymap aliases (#12976)

* Add support for up to 4 IS31FL3733 drivers (#12342)

* Convert Encoder callbacks to be boolean functions (#12805)

* [Keyboard] Fix Terrazzo build failure (#12977)

* Do not hard set config in CPTC files (#11864)

* [Keyboard] Corne - Remove legacy revision support (#12226)

* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)

* Add Full-duplex serial driver for ARM boards (#9842)

* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)

* Backlight: add defines for default level and breathing state (#12560)

* Add dire message about LUFA mass storage bootloader (#13014)

* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)

Was causing compiler errors on some systems.

* Fix keyboards/keymaps for boolean encoder callback changes (#12985)

* `backlight.c`: include `eeprom.h` (#13024)

* Add changelog for 2021-05-29 Breaking Changes merge (#12939)

* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version

* Add recent develop changes

* Sort recent develop changes

* Remove sections for ChibiOS changes per tzarc

No ChibiOS changes this round.

* Add and sort recent develop changes

* add notes about keyboard moves/deletions

* import changelog for PR 12172

Documents the change to BOOTMAGIC_ENABLE.

* update section headings

* re-sort changelog

* add additional note regarding Bootmagic changes

* remove changelog timestamp

* update dates in main Breaking Changes docs

* fix broken section anchors in previous changelogs

* add link to backlight/eeprom patch to changelog

* highlight some more changes

* link PRs from section headers

* Restore standard readme

* run: qmk cformat --core-only

* Add Launchpad keymap

Note: RGB and Audio won't work when using B pins for audio

* Add support for rgb matrix on launchpad

* Update config for launchpag

* Disable wait on layer change

* Update config for ErgoDox EZ

* Fixup rgb light userspace code

* Move Corne layout to community layouts folder

* Update config for corne to support community layouts

* Add license header to files

* Minor cleanup of userspace config

* Update Pimironi Trackball code

* Increase debounce time on ergodox

* Fix keymap handling

* Enable wait for USB for moonlander

* Update/add license headers

* fix review issues

* Add Kyria Keymap

* Enable all RGBLIGHT Animations for ARM and high capacity AVR

* Reduce GNUC version for __has_include

* Cleanup Ortho 4x12 Community layout

* Update Collide 39 keymap

* Cleanup Keymaps

* Enable full 30 LEDs for Ergodox

* Change EEPROM Load timing

* Use RGB Matrix on Planck Rev6

* Use correct keymap swap

* Enable everything for ARM

* Only enable rgb sleep on avr until crash is fixed

* Add additional Kyria keymap config

* Overhaul Kyria OLED display

* Improve kyria keymap based on usage

* Minor tweaks to rules

* Update OLED code to truncate properly

* Fix RGB Light layer indication

* Switch all of biton32 to get_highest_layer function

* Fix OLED Keylogger display

* Run qmk cformat over all of my user files

* Slight tweak to kyria based on usage

* Move around LALT_T config

* Add comments about base wrappers to keymaps

* Another cformat pass

* Temp fix for VUSB boards and NKRO

* Convert tabs to spaces in rules.mk files

* Only enable RGBLight if it's enabled

* Add Encoder Flip setting

* Update OLED font file

* Add a quefrency keymap

* New Alt-ernate layouts

* Enable Per Key Tapping Term to preserve sanity

* Use underglow and mod lights for status on Corne

* Update the drashna_ms keymap for quefrency

* Disable Audio since there isn't enough space

* Update KC_MAKE to ues :flash target

* Cleanup ergodox layout

* Enable i2c support for Iris

* Add keymap support for CG_SWAP

* Enable RGB Matrix Shutdown mode

* enable heatmap

* Update gitlab CI to install python3

* Remove game macros

These are no longer needed, and haven't been used in ages

* Cleanup planck layout

* Add RGB Matrix fun and RGB cleanup

* Add keycode and config for RGB Matrix idle animations

* Clean up rgb idle animation code

* Add rgb idle keycode to keymaps

* Fix issues with rgb matrix idle animation

* Fix some handling for idle animation

* Reduce idle animation timeout to 15s to be more reasonable

* fix up rgb stuff

* Fix isses with rgb functions not being called for matrix

* Use custom EEPROM Magic Number so testing is easier

* Extend Default Layer macro to support a lot more layers

* Fix bjohnson macropad

* Adjust KC_MAKE to process mods for more consistent behavior

* Fix up rgb stuff on corne

* Corne OLED Overhaul

* Fixes a number of issues with weirdness.
* Fixes issues with keylogger (should be more reliable now)
* Modulaize the OLED render sections
* Rewrite layer display code
* Update URL for Font Editor

Due to odd issues, I ended up rewriting from scratch.  And using PROGMEM versions, since I think I was getting memory overflows.

* Update polling rate on all keebs

* Fix planck ez layout config

* Remove macros from Viterbi

* Fix my Tap Dance issues after I broke them

* Cleanup and organization of userspace documentation

As well as some additional cleanup of functions due to review of documentation.

* Enable Tapdance on Glow and remove more animations

* Revert to Eager PR debouncing

* Add better check for startup animation

* Move where RGB Matrix defines are listed

* Limit RGB Matrix max val

* Update keyboard for Iris Rev 3 conflicts

* Enable encoder support on planck ez

* Remove is_master check from corne\'s OLED code

* Overhaul OLED screens for my Corne

* One last removal

* Show RGB valu On both sides

* Updates for OLED display info

* Fix compile issues for rgb config

* Disabled Space Cadet for all drashna keymaps

* Fix OLED Screen configs

* Minor OLED Tweaks

* Revert some Iris changes

* Fix song include

* Handle MAKE macro for the Corne boards better

* Add super hacky-hack for eeconfig initialization

* Add audio support for Fractal since Elite Cs support it

* Add defines for keycode steps

* Add White layout

* Update Corne RGB info

* Add fun effects to layer indication for RGB Matrix enabled boards

* Use proper define for product name detection

* Update formatting

* Use custom timeout mechanism for OLED timeout

* Fix up OLED screen HSV code for new HSV structure

* Better handle turning off RGB Matrix when sleeping

* Disable MultiSplash Animation

* Change Iris back to using serial

* Why was RGB disabled?!?!?!

* Limit val in rgb_matrix_layer_helper function

* Remove EECONFIG setting for RGB matrix

* Make CRKBD keylogger output actually show tap keys

* check MT/LT for twinkling

* Add ortho 5x12 support for fractal keyboard

* Use newer interface for setting pins/ports

* Remove custom unicode methods

* Reomve unicode input info

* Odd rules issue

* Redefine REST note to be more pleasing

* Properly disable PM LEDs with GPIO commands

* Update gitlab CI yaml file

* Remove extra mod tap check

* Remove initial state on ergodox glow

* Rev6 Cleanup

* Fix KC_MAKE macro

* Update GitLab CI yaml file

* More GitLab CI changes

* One final GitLab CI change

* Remove unneeded unicode support

* Optimize KC_MAKE