You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 

106 lines
3.8 KiB

#include "bootloader.h"
#include <ch.h>
#include <hal.h>
#include "wait.h"
/* This code should be checked whether it runs correctly on platforms */
#define SYMVAL(sym) (uint32_t)(((uint8_t *)&(sym)) - ((uint8_t *)0))
#define BOOTLOADER_MAGIC 0xDEADBEEF
#define MAGIC_ADDR (unsigned long *)(SYMVAL(__ram0_end__) - 4)
#ifndef STM32_BOOTLOADER_DUAL_BANK
# define STM32_BOOTLOADER_DUAL_BANK FALSE
#endif
#if STM32_BOOTLOADER_DUAL_BANK
// Need pin definitions
# include "config_common.h"
# ifndef STM32_BOOTLOADER_DUAL_BANK_GPIO
# error "No STM32_BOOTLOADER_DUAL_BANK_GPIO defined, don't know which pin to toggle"
# endif
# ifndef STM32_BOOTLOADER_DUAL_BANK_POLARITY
# define STM32_BOOTLOADER_DUAL_BANK_POLARITY 0
# endif
# ifndef STM32_BOOTLOADER_DUAL_BANK_DELAY
# define STM32_BOOTLOADER_DUAL_BANK_DELAY 100000
# endif
extern uint32_t __ram0_end__;
__attribute__((weak)) void bootloader_jump(void) {
// For STM32 MCUs with dual-bank flash, and we're incapable of jumping to the bootloader. The first valid flash
// bank is executed unconditionally after a reset, so it doesn't enter DFU unless BOOT0 is high. Instead, we do
// it with hardware...in this case, we pull a GPIO high/low depending on the configuration, connects 3.3V to
// BOOT0's RC charging circuit, lets it charge the capacitor, and issue a system reset. See the QMK discord
// #hardware channel pins for an example circuit.
palSetPadMode(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_MODE_OUTPUT_PUSHPULL);
# if STM32_BOOTLOADER_DUAL_BANK_POLARITY
palSetPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
# else
palClearPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
# endif
// Wait for a while for the capacitor to charge
wait_ms(100);
// Issue a system reset to get the ROM bootloader to execute, with BOOT0 high
NVIC_SystemReset();
}
void enter_bootloader_mode_if_requested(void) {} // not needed at all, but if anybody attempts to invoke it....
#elif defined(STM32_BOOTLOADER_ADDRESS) // STM32_BOOTLOADER_DUAL_BANK
extern uint32_t __ram0_end__;
__attribute__((weak)) void bootloader_jump(void) {
*MAGIC_ADDR = BOOTLOADER_MAGIC; // set magic flag => reset handler will jump into boot loader
NVIC_SystemReset();
}
void enter_bootloader_mode_if_requested(void) {
unsigned long *check = MAGIC_ADDR;
if (*check == BOOTLOADER_MAGIC) {
*check = 0;
__set_CONTROL(0);
__set_MSP(*(__IO uint32_t *)STM32_BOOTLOADER_ADDRESS);
__enable_irq();
typedef void (*BootJump_t)(void);
BootJump_t boot_jump = *(BootJump_t *)(STM32_BOOTLOADER_ADDRESS + 4);
boot_jump();
while (1)
;
}
}
#elif defined(KL2x) || defined(K20x) || defined(MK66F18) // STM32_BOOTLOADER_DUAL_BANK // STM32_BOOTLOADER_ADDRESS
/* Kinetis */
# if defined(BOOTLOADER_KIIBOHD)
/* Kiibohd Bootloader (MCHCK and Infinity KB) */
# define SCB_AIRCR_VECTKEY_WRITEMAGIC 0x05FA0000
const uint8_t sys_reset_to_loader_magic[] = "\xff\x00\x7fRESET TO LOADER\x7f\x00\xff";
__attribute__((weak)) void bootloader_jump(void) {
__builtin_memcpy((void *)VBAT, (const void *)sys_reset_to_loader_magic, sizeof(sys_reset_to_loader_magic));
// request reset
SCB->AIRCR = SCB_AIRCR_VECTKEY_WRITEMAGIC | SCB_AIRCR_SYSRESETREQ_Msk;
}
# else /* defined(BOOTLOADER_KIIBOHD) */
/* Default for Kinetis - expecting an ARM Teensy */
# include "wait.h"
__attribute__((weak)) void bootloader_jump(void) {
wait_ms(100);
__BKPT(0);
}
# endif /* defined(BOOTLOADER_KIIBOHD) */
#else /* neither STM32 nor KINETIS */
__attribute__((weak)) void bootloader_jump(void) {}
#endif