You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
213 lines
6.2 KiB
213 lines
6.2 KiB
/* Copyright 2021 Colin Lam (Ploopy Corporation)
|
|
* Copyright 2020 Christopher Courtney, aka Drashna Jael're (@drashna) <drashna@live.com>
|
|
* Copyright 2019 Sunjun Kim
|
|
* Copyright 2019 Hiroyuki Okada
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include "adns5050.h"
|
|
#include "wait.h"
|
|
#include "debug.h"
|
|
#include "gpio.h"
|
|
|
|
// Registers
|
|
// clang-format off
|
|
#define REG_PRODUCT_ID 0x00
|
|
#define REG_REVISION_ID 0x01
|
|
#define REG_MOTION 0x02
|
|
#define REG_DELTA_X 0x03
|
|
#define REG_DELTA_Y 0x04
|
|
#define REG_SQUAL 0x05
|
|
#define REG_SHUTTER_UPPER 0x06
|
|
#define REG_SHUTTER_LOWER 0x07
|
|
#define REG_MAXIMUM_PIXEL 0x08
|
|
#define REG_PIXEL_SUM 0x09
|
|
#define REG_MINIMUM_PIXEL 0x0a
|
|
#define REG_PIXEL_GRAB 0x0b
|
|
#define REG_MOUSE_CONTROL 0x0d
|
|
#define REG_MOUSE_CONTROL2 0x19
|
|
#define REG_LED_DC_MODE 0x22
|
|
#define REG_CHIP_RESET 0x3a
|
|
#define REG_PRODUCT_ID2 0x3e
|
|
#define REG_INV_REV_ID 0x3f
|
|
#define REG_MOTION_BURST 0x63
|
|
// clang-format on
|
|
|
|
void adns5050_init(void) {
|
|
// Initialize the ADNS serial pins.
|
|
setPinOutput(ADNS5050_SCLK_PIN);
|
|
setPinOutput(ADNS5050_SDIO_PIN);
|
|
setPinOutput(ADNS5050_CS_PIN);
|
|
|
|
// reboot the adns.
|
|
// if the adns hasn't initialized yet, this is harmless.
|
|
adns5050_write_reg(REG_CHIP_RESET, 0x5a);
|
|
|
|
// wait maximum time before adns is ready.
|
|
// this ensures that the adns is actuall ready after reset.
|
|
wait_ms(55);
|
|
|
|
// read a burst from the adns and then discard it.
|
|
// gets the adns ready for write commands
|
|
// (for example, setting the dpi).
|
|
adns5050_read_burst();
|
|
}
|
|
|
|
// Perform a synchronization with the ADNS.
|
|
// Just as with the serial protocol, this is used by the slave to send a
|
|
// synchronization signal to the master.
|
|
void adns5050_sync(void) {
|
|
writePinLow(ADNS5050_CS_PIN);
|
|
wait_us(1);
|
|
writePinHigh(ADNS5050_CS_PIN);
|
|
}
|
|
|
|
void adns5050_cs_select(void) {
|
|
writePinLow(ADNS5050_CS_PIN);
|
|
}
|
|
|
|
void adns5050_cs_deselect(void) {
|
|
writePinHigh(ADNS5050_CS_PIN);
|
|
}
|
|
|
|
uint8_t adns5050_serial_read(void) {
|
|
setPinInput(ADNS5050_SDIO_PIN);
|
|
uint8_t byte = 0;
|
|
|
|
for (uint8_t i = 0; i < 8; ++i) {
|
|
writePinLow(ADNS5050_SCLK_PIN);
|
|
wait_us(1);
|
|
|
|
byte = (byte << 1) | readPin(ADNS5050_SDIO_PIN);
|
|
|
|
writePinHigh(ADNS5050_SCLK_PIN);
|
|
wait_us(1);
|
|
}
|
|
|
|
return byte;
|
|
}
|
|
|
|
void adns5050_serial_write(uint8_t data) {
|
|
setPinOutput(ADNS5050_SDIO_PIN);
|
|
|
|
for (int8_t b = 7; b >= 0; b--) {
|
|
writePinLow(ADNS5050_SCLK_PIN);
|
|
|
|
if (data & (1 << b))
|
|
writePinHigh(ADNS5050_SDIO_PIN);
|
|
else
|
|
writePinLow(ADNS5050_SDIO_PIN);
|
|
|
|
wait_us(2);
|
|
|
|
writePinHigh(ADNS5050_SCLK_PIN);
|
|
}
|
|
|
|
// tSWR. See page 15 of the ADNS spec sheet.
|
|
// Technically, this is only necessary if the next operation is an SDIO
|
|
// read. This is not guaranteed to be the case, but we're being lazy.
|
|
wait_us(4);
|
|
|
|
// Note that tSWW is never necessary. All write operations require at
|
|
// least 32us, which exceeds tSWW, so there's never a need to wait for it.
|
|
}
|
|
|
|
// Read a byte of data from a register on the ADNS.
|
|
// Don't forget to use the register map (as defined in the header file).
|
|
uint8_t adns5050_read_reg(uint8_t reg_addr) {
|
|
adns5050_cs_select();
|
|
|
|
adns5050_serial_write(reg_addr);
|
|
|
|
// We don't need a minimum tSRAD here. That's because a 4ms wait time is
|
|
// already included in adns5050_serial_write(), so we're good.
|
|
// See page 10 and 15 of the ADNS spec sheet.
|
|
// wait_us(4);
|
|
|
|
uint8_t byte = adns5050_serial_read();
|
|
|
|
// tSRW & tSRR. See page 15 of the ADNS spec sheet.
|
|
// Technically, this is only necessary if the next operation is an SDIO
|
|
// read or write. This is not guaranteed to be the case.
|
|
// Honestly, this wait could probably be removed.
|
|
wait_us(1);
|
|
|
|
adns5050_cs_deselect();
|
|
|
|
return byte;
|
|
}
|
|
|
|
void adns5050_write_reg(uint8_t reg_addr, uint8_t data) {
|
|
adns5050_cs_select();
|
|
adns5050_serial_write(0b10000000 | reg_addr);
|
|
adns5050_serial_write(data);
|
|
adns5050_cs_deselect();
|
|
}
|
|
|
|
report_adns5050_t adns5050_read_burst(void) {
|
|
adns5050_cs_select();
|
|
|
|
report_adns5050_t data;
|
|
data.dx = 0;
|
|
data.dy = 0;
|
|
|
|
adns5050_serial_write(REG_MOTION_BURST);
|
|
|
|
// We don't need a minimum tSRAD here. That's because a 4ms wait time is
|
|
// already included in adns5050_serial_write(), so we're good.
|
|
// See page 10 and 15 of the ADNS spec sheet.
|
|
// wait_us(4);
|
|
|
|
uint8_t x = adns5050_serial_read();
|
|
uint8_t y = adns5050_serial_read();
|
|
|
|
// Burst mode returns a bunch of other shit that we don't really need.
|
|
// Setting CS to high ends burst mode early.
|
|
adns5050_cs_deselect();
|
|
|
|
data.dx = convert_twoscomp(x);
|
|
data.dy = convert_twoscomp(y);
|
|
|
|
return data;
|
|
}
|
|
|
|
// Convert a two's complement byte from an unsigned data type into a signed
|
|
// data type.
|
|
int8_t convert_twoscomp(uint8_t data) {
|
|
if ((data & 0x80) == 0x80)
|
|
return -128 + (data & 0x7F);
|
|
else
|
|
return data;
|
|
}
|
|
|
|
// Don't forget to use the definitions for CPI in the header file.
|
|
void adns5050_set_cpi(uint16_t cpi) {
|
|
uint8_t cpival = constrain((cpi / 125), 0x1, 0xD); // limits to 0--119
|
|
|
|
adns5050_write_reg(REG_MOUSE_CONTROL2, 0b10000 | cpival);
|
|
}
|
|
|
|
uint16_t adns5050_get_cpi(void) {
|
|
uint8_t cpival = adns5050_read_reg(REG_MOUSE_CONTROL2);
|
|
return (uint16_t)((cpival & 0b10000) * 125);
|
|
}
|
|
|
|
bool adns5050_check_signature(void) {
|
|
uint8_t pid = adns5050_read_reg(REG_PRODUCT_ID);
|
|
uint8_t rid = adns5050_read_reg(REG_REVISION_ID);
|
|
uint8_t pid2 = adns5050_read_reg(REG_PRODUCT_ID2);
|
|
|
|
return (pid == 0x12 && rid == 0x01 && pid2 == 0x26);
|
|
}
|