[eGTouchL.ini]
DebugEnableBits			1
ShowDebugPosition		0
DeviceNums			1
BaudRate			0
ScanInterface			0
UseDriverCalib			0
SkipFirstByte			0
ShiftByteBothEnd		1
ScanDevStartDelayTime		0

[String]
SerialPath0				default
SerialPath1				default
DevPID0					null
DevPID1					null

[Device_No.0]
Physical_Address
SupportPoints			10
SendRawPoints			0
Direction			0		
Orientation			0
EdgeCompensate			0
	EdgeLeft			100
	EdgeRight			100
	EdgeTop				100
	EdgeBottom			100
HoldFilterEnable		0
	HoldRange			20
SplitRectMode			0
	CustomRectLeft			0
	CustomRectRight			2047
	CustomRectTop			0
	CustomRectBottom		2047
MonitorName				null
DetectRotation			0
ReportMode				1
EventType				0
BtnType					0
RightClickEnable		1	
	RightClickDuration		1500
	RightClickRange			20
BeepState			0
	BeepDevice			0
	BeepFreq			1000
	BeepLen				200
VKEYEnable                      0
        VKEYReportMod           1
        VKEY_0                  0
[EndOfDevice]

[EndOfFile]





[NOTE]:
1. 	Remember to put this file at /etc/eGTouchL.ini
2.	This is a parameter list that we can enable or disable functions easily by modifying the above list.
3.	Please make sure just modify the value of the list. "DONT" change any front title of the list.
4.	Below are the parameter explanations. 
		
[Explanation of all Parameter]:
DebugEnableBits			[0] Close all Debug	, [FFFFF] Open all Debug
ShowDebugPosition		[0] Print in file under /tmp , [1] Print in Terminal , [2] Print in both
SerialPath			[default]: It represent serial port use default /dev/ttySX
				/dev/serial/ttyS0: It represent assign the specific serial port. Pls be accordance to the form.
ScanDevStartDelayTime	Driver booting delay time,  the unit is millisecond.
Physical_Address	USB physical address ( use for multi-device )
SupportPoints			[0] No point , [X] Point amount want to report
SendRawPoints		[0] default point format , [1] raw point format 
Direction			[1] Invert X   , [2] Invert Y   , [4] Swap X with Y
Orientation			[0] 0 degree, [1] 90 degree, [2] 180 degree, [3] 270 degree
EdgeCompensate			[0] Disbale	, [1] Enable
	EdgeLeft			[100] Default with no change , [50-150] Compensate Value.
	EdgeRight			[100] Default with no change , [50-150] Compensate Value.
	EdgeTop				[100] Default with no change , [50-150] Compensate Value.
	EdgeBottom			[100] Default with no change , [50-150] Compensate Value.
HoldFilterEnable		[0] Disable , [1] Enable
	HoldRange			[X] Hold Filter Range area
SplitRectMode			[0] Default	, [1-8] In-built Mode , [9] Custom Mode
	CustomRectLeft			[0-2047] As Custom Mode, left edge value
	CustomRectRight			[0-2047] As Custom Mode, right edge value
	CustomRectTop			[0-2047] As Custom Mode, top edge value
	CustomRectBottom		[0-2047] As Custom Mode, bottom edge value
ReportMode			[1] Normal Mode [2] Single Click on Touch [3] Single Click on Release
MonitorName			Use for mapping touch data output to specific monitor. Check monitor name by command "xrandr", example: "eDP1".
DetectRotation		[0] Disable [1] Enable to detect X rotation and map coordinate.
EventType			[0]	AUTO_DETECT
BtnType				[0] BTN_LEFT	[1] ABS_PRESSURE	[2] BTN_TOUCH
RightClick			[0] Disable RightClick, [1] Enable RightClick
	RightClickDuration		[X] After constant touch for X millisec, trigger RightClick
	RightClickRange			[X] The touch range(area) which would cause constant touch
BeepState			[0] Disable beep [1] Beep on Touch [2] Beep on Release
	BeepDevice		[0] Disable [1] System Beep [2] Sound Card Beep
	BeepFreq		[X] Beep sound frequency
	BeepLen			[X] Beep sound length