lc-coreboot/x230

Skulls - Thinkpad X230.

Latest release (config overview and version info)

• Get it from our release page
• The only proprietary binary, the VGA BIOS is executed in "secure" mode (PCI_OPTION_ROM_RUN_YABEL)

coreboot

• We simply take coreboot's current state in it's master branch at the time we build a release image. That's the preferred way to use coreboot. The git revision we use is always included in the release.

Intel microcode

• revision 1f from 2018-02-07 see package 20180312 under Intel's license

SeaBIOS

• version 1.11.1 from 2018-03-19

table of contents

• TL;DR
• Flashing for the first time
• How to flash
• Why does this work

TL;DR

For first-time flashing, remove the keyboard and palmrest, and (using a Raspberry Pi with a SPI 8-pin chip clip connected), run external_install_bottom.sh on the lower chip and external_install_top.sh on the top chip of the two.

For updating later, run x230_update.sh. No need to disassemble.

And always use the latest released package. This will be tested. The git master branch is not meant to be stable. Use it for testing only.

Flashing for the first time

• Before doing anything, run Linux, install dmidecode and run x230_before_first_install.sh It simply prints valuable system information.
• Make sure you have RAM that uses 1,5V, not 1,35V. Check the specification of your RAM module(s).
• Especially for the first time, you must flash externally. See below for the details for using a Rapberry Pi, for example.

before you begin: original update / EC firmware (optional)

Before flashing coreboot, consider doing one original Lenovo upgrade process in case you're not running the latest version. This is not supported anymore, once you're running coreboot (You'd have to manually flash back your backup images first, see later chapters).

Also, this updates the BIOS and Embedded Controller (EC) firmware. The EC is not updated anymore, when running coreboot. The latest EC version is 1.14 and that's unlikely to change.

In case you're not running the latest BIOS version, either

• use the latest original CD and burn it, or
• use the same, only with a patched EC firmware that allows using any battery:

Disable the battery validation check

By default, only original Lenovo batteries are allowed. Thanks to this project we can use Lenovo's bootable upgrade image, change it and create a bootable USB image, with an EC update that allows us to use any 3rd party aftermarket battery:

sudo apt-get install build-essential git mtools libssl-dev
git clone https://github.com/hamishcoleman/thinkpad-ec && cd thinkpad-ec
make patch_disable_keyboard clean
make patch_enable_battery clean
make patched.x230.img

That's it. You can create a bootable USB stick: sudo dd if=patched.x230.img of=/dev/sdx and boot from it. Alternatively, burn patched.x230.iso to a CD. And make sure you have "legacy" boot set, not "UEFI" boot.

preparation: required hardware

• An 8 Pin SOIC Clip, for example from Pomona electronics or alternatively hooks, for example from E-Z-Hook
• 6 female jumper wires to connect the clip to a hardware flasher
• a hardware flasher supported by flashrom but we currently only support using a Raspberry Pi

ifd unlock and me_cleaner: the 8MB chip

The Intel Management Engine resides on the 8MB chip (at the bottom, closer to you). We don't need to touch it for coreboot-upgrades in the future, but to enable internal flashing, we need to unlock it once. We run ifdtool and, while we are at it, me_cleaner on it:

We support using a RPi, see below for the connection details. Move the release-tarball to the RPi (USB Stick or however) and unpack it (to the current directory and change into it):

mkdir tarball_extracted
tar -xf <tarball>.tar.xz -C tarball_extracted
cd tarball_extracted

And finally unlock the 8M chip by using the included script (be patient). Again, this doesn't replace much; it reads the original, unlocks and flashes back:

sudo ./external_install_bottom.sh -m -k <backup.bin>

That's it. Keep the backup safe.

background (just so you know)

• The -m option above also runs me_cleaner -S before flashing back.

• The -l option will (re-)lock your flash ROM, in case you want to force yourself (and others) to hardware-flashing externally.

• If you don't use a RPi, change the flashrom programmer to your needs.This is roughly what's going on:

  flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=128 -r ifdmegbe.rom
  flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=128 -r ifdmegbe2.rom
  diff ifdmegbe.rom ifdmegbe2.rom
  git clone https://github.com/corna/me_cleaner.git && cd me_cleaner
  ./me_cleaner.py -S -O ifdmegbe_meclean.rom ifdmegbe.rom
  ifdtool -u ifdmegbe_meclean.rom
  flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=128 -w ifdmegbe_meclean.rom.new
  

• We (or our scripts) use flashrom for flashing. If our scripts don't detect the chip automatically, connect the programmer to the chip and run flashrom -p <your_hardware> (for example flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=128 for the Raspberry Pi) to let flashrom detect the chip. If -c is omitted, the scripts will run this for you. It will probably list a few you need to choose from when flashing (by adding -c <chipname>). In case you are unsure what to specify, here's some examples we find out there:

  • 4MB chip

    • MX25L3206E seems to mostly be in use

  • 8MB chip

    • MX25L6406E/MX25L6408E is used in this guide
    • MX25L3206E/MX25L3208E is seen working with various X230 models.
    • EN25QH64 is used sometimes

BIOS: the 4MB chip

(internally, memory of the two chips is mapped together, the 8MB being the lower part, but we can essientially ignore that). Again, using a RPi is supported here. We assume you have the unpacked release tarball ready, see above. Use the following included script:

sudo ./external_install_top.sh -i x230_coreboot_seabios_<hash>_top.rom -k <backup>

That's it. Keep the backup safe.

How to flash

When upgrading to a new release, only the "upper" 4MB chip has to be written and any of the following examples are possible. Otherwise you cannot use "internal" flashing and please read flashing for the first time.

Example: internal

• Only for updating! You have to have your 8MB chip flashed externally using our external_install_bottom.sh script (ifdtool -u) before this, once
• very convenient: just install flashrom on your X230 but according to the flashrom manpage this is very dangerous!
• Boot Linux with the iomem=relaxed boot parameter (for example set in /etc/default/grub)
• download the latest release tarball (4MB "top" BIOS image is included) and extract it
• run x230_update.sh for generating all necessary files and instructions

Example: Raspberry Pi 3

Here you'll flash externally, using a test clip or hooks, see required hardware. Remove the 7 screws to remove the keyboard (by pushing it towards the screen before lifting) and the palmrest. You'll find the chips using the photo below. This is how the SPI connection looks on both chips:

    Screen (furthest from you)
             __
      MOSI  5 --|  |-- 4  GND
       CLK  6 --|  |-- 3  N/C
       N/C  7 --|  |-- 2  MISO
       VCC  8 --|__|-- 1  CS

       Edge (closest to you)

We run Raspbian and have the following setup

• Serial connection using a "USB to Serial" UART Adapter and picocom or minicom (yes, in this case you need a second PC connected to the RPi over UART)

• in the SD Cards's /boot/config.txt file enable_uart=1 and dtparam=spi=on

• For flashrom we put spi_bcm2835 and spidev in /etc/modules

• Connect to a wifi or ethernet to sudo apt-get install flashrom

• connect the Clip to the Raspberry Pi 3 (there are prettier images too):

       Edge of pi (furthest from you)
                   (UART)
     L           GND TX  RX                           CS
     E            |   |   |                           |
     F +---------------------------------------------------------------------------------+
     T |  x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x  |
       |  x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x  |
     E +----------------------------------^---^---^---^-------------------------------^--+
     D                                    |   |   |   |                               |
     G                                   3.3V MOSIMISO|                              GND
     E                                 (VCC)         CLK
       Body of Pi (closest to you)
  

Now copy our release tarball over to the Rasperry Pi. One way to copy, is convertig it to ascii using uuencode (part of Debian's sharutils package) described below. This is a direct, shady and slow way to transfer a file. Use a USB Stick or scp instead. :) (but you need even more hardware or a network).

    (convert)
host$ uuencode <tarball> <tarball>.ascii > <tarball>.ascii
    (transfer)
rpi$ cat > <tarball>.ascii
host$ pv <tarball>.ascii > /dev/ttyUSBX
    (wait)
rpi$ (CTRL-D)
    (convert back)
rpi$ uudecode -o <tarball> <tarball>.ascii
    (verify)
host$ sha1sum <tarball>
rpi$ sha1sum <tarball>

Unpack it:

mkdir tarball_extracted
tar -xf <tarball> -C tarball_extracted
cd tarball_extracted

Connect the SPI clip to the "top" chip, and run:

sudo ./external_install_top.sh -f rpi -i x230_coreboot_seabios_<hash>_top.rom

That's it.

background (just so you know)

• Connecting an ethernet cable as a power-source for SPI (instead of the VCC pin) is not necessary (some other flashing how-to guides mention this). Setting a fixed (and low) SPI speed for flashrom offeres the same stability. Our scripts do this for you.

Why does this work?

On the X230, there are 2 physical "BIOS" chips. The "upper" 4MB one holds the actual bios we can generate using coreboot, and the "lower" 8MB one holds the rest that you can modify yourself once, if you like, but strictly speaking, you don't need to touch it at all. What's this "rest"? Mainly a tiny binary used by the Ethernet card and the Intel Management Engine.