|
|
- //--------------------------------------------------------------------------------
- // Internal popwer montior
- // Enable support by passing ENABLE_VCC_REPORT=1 build flag
- //--------------------------------------------------------------------------------
-
- #if (MQTT_REPORTS | MQTT_VCC_REPORT)
- ADC_MODE(ADC_VCC);
- #endif
-
- //--------------------------------------------------------------------------------
- // Custom RF module
- // Check http://tinkerman.cat/adding-rf-to-a-non-rf-itead-sonoff/
- // Enable support by passing ENABLE_RF=1 build flag
- //--------------------------------------------------------------------------------
-
- #define RF_PIN 14
- #define RF_CHANNEL 31
- #define RF_DEVICE 1
-
- //--------------------------------------------------------------------------------
- // DHTXX temperature/humidity sensor
- // Enable support by passing ENABLE_DHT=1 build flag
- //--------------------------------------------------------------------------------
-
- #define DHT_PIN 14
- #define DHT_UPDATE_INTERVAL 60000
- #define DHT_TYPE DHT22
- #define DHT_TIMING 11
- #define DHT_TEMPERATURE_TOPIC "/temperature"
- #define DHT_HUMIDITY_TOPIC "/humidity"
-
- #define HUMIDITY_NORMAL 0
- #define HUMIDITY_COMFORTABLE 1
- #define HUMIDITY_DRY 2
- #define HUMIDITY_WET 3
-
- //--------------------------------------------------------------------------------
- // DS18B20 temperature sensor
- // Enable support by passing ENABLE_DS18B20=1 build flag
- //--------------------------------------------------------------------------------
-
- #define DS_PIN 14
- #define DS_UPDATE_INTERVAL 60000
- #define DS_TEMPERATURE_TOPIC "/temperature"
-
- //--------------------------------------------------------------------------------
- // Custom current sensor
- // Check http://tinkerman.cat/your-laundry-is-done/
- // Check http://tinkerman.cat/power-monitoring-sonoff-th-adc121/
- // Enable support by passing ENABLE_EMON=1 build flag
- //--------------------------------------------------------------------------------
-
- #define EMON_ANALOG_PROVIDER 0
- #define EMON_ADC121_PROVIDER 1
-
- // If you select EMON_ADC121_PROVIDER you need to enable and configure I2C in general.h
- #define EMON_PROVIDER EMON_ANALOG_PROVIDER
-
- #if EMON_PROVIDER == EMON_ANALOG_PROVIDER
- #define EMON_CURRENT_PIN 0
- #define EMON_ADC_BITS 10
- #define EMON_REFERENCE_VOLTAGE 1.0
- #define EMON_CURRENT_PRECISION 1
- #define EMON_CURRENT_OFFSET 0.25
- #endif
-
- #if EMON_PROVIDER == EMON_ADC121_PROVIDER
- #define EMON_ADC121_ADDRESS 0x50
- #define EMON_ADC_BITS 12
- #define EMON_REFERENCE_VOLTAGE 3.3
- #define EMON_CURRENT_PRECISION 2
- #define EMON_CURRENT_OFFSET 0.10
- #endif
-
- #define EMON_CURRENT_RATIO 30
- #define EMON_SAMPLES 1000
- #define EMON_INTERVAL 10000
- #define EMON_MEASUREMENTS 6
- #define EMON_MAINS_VOLTAGE 230
- #define EMON_APOWER_TOPIC "/apower"
- #define EMON_ENERGY_TOPIC "/energy"
- #define EMON_CURRENT_TOPIC "/current"
-
- //--------------------------------------------------------------------------------
- // HLW8012 power sensor (Sonoff POW)
- // Enable support by passing ENABLE_POW=1 build flag
- // Enabled by default when selecting SONOFF_POW hardware
- //--------------------------------------------------------------------------------
-
- #define POW_SEL_PIN 5
- #define POW_CF1_PIN 13
- #define POW_CF_PIN 14
- #define POW_USE_INTERRUPTS 1
- #define POW_SEL_CURRENT HIGH
- #define POW_CURRENT_R 0.001
- #define POW_VOLTAGE_R_UP ( 5 * 470000 ) // Real: 2280k
- #define POW_VOLTAGE_R_DOWN ( 1000 ) // Real 1.009k
- #define POW_POWER_TOPIC "/power"
- #define POW_CURRENT_TOPIC "/current"
- #define POW_VOLTAGE_TOPIC "/voltage"
- #define POW_APOWER_TOPIC "/apower"
- #define POW_RPOWER_TOPIC "/rpower"
- #define POW_PFACTOR_TOPIC "/pfactor"
- #define POW_ENERGY_TOPIC "/energy"
- #define POW_UPDATE_INTERVAL 5000
- #define POW_REPORT_EVERY 12
|
