mhsw-espurna/code/espurna/config/sensors.h

// =============================================================================
// SENSORS - General data
// =============================================================================

#define SENSOR_DEBUG                        0               // Debug sensors

#define SENSOR_READ_INTERVAL                6               // Read data from sensors every 6 seconds
#define SENSOR_READ_MIN_INTERVAL            6               // Minimum read interval
#define SENSOR_READ_MAX_INTERVAL            3600            // Maximum read interval
#define SENSOR_INIT_INTERVAL                10000           // Try to re-init non-ready sensors every 10s

#define SENSOR_REPORT_EVERY                 10              // Report every this many readings
#define SENSOR_REPORT_MIN_EVERY             1               // Minimum every value
#define SENSOR_REPORT_MAX_EVERY             12              // Maximum

#define SENSOR_USE_INDEX                    0               // Use the index in topic (i.e. temperature/0)
                                                            // even if just one sensor (0 for backwards compatibility)

#ifndef SENSOR_POWER_CHECK_STATUS
#define SENSOR_POWER_CHECK_STATUS           1               // If set to 1 the reported power/current/energy will be 0 if the relay[0] is OFF
#endif

#ifndef SENSOR_TEMPERATURE_CORRECTION
#define SENSOR_TEMPERATURE_CORRECTION       0.0             // Offset correction
#endif

#ifndef TEMPERATURE_MIN_CHANGE
#define TEMPERATURE_MIN_CHANGE              0.0             // Minimum temperature change to report
#endif

#ifndef SENSOR_HUMIDITY_CORRECTION
#define SENSOR_HUMIDITY_CORRECTION          0.0             // Offset correction
#endif

#ifndef HUMIDITY_MIN_CHANGE
#define HUMIDITY_MIN_CHANGE                 0               // Minimum humidity change to report
#endif

// American Society of Heating, Refrigerating and Air-Conditioning Engineers suggests a range of 45% - 55% humidity to manage health effects and illnesses.
// Comfortable: 30% - 60%
// Recommended: 45% - 55%
// High       : 55% - 80%
#define HUMIDITY_NORMAL                     0               // > %30
#define HUMIDITY_COMFORTABLE                1               // > %45
#define HUMIDITY_DRY                        2               // < %30
#define HUMIDITY_WET                        3               // > %70

// United States Environmental Protection Agency - UV Index Scale
// One UV Index unit is equivalent to 25 milliWatts per square meter.
#define UV_INDEX_LOW                        0               // 0 to 2 means low danger from the sun's UV rays for the average person.
#define UV_INDEX_MODERATE                   1               // 3 to 5 means moderate risk of harm from unprotected sun exposure.
#define UV_INDEX_HIGH                       2               // 6 to 7 means high risk of harm from unprotected sun exposure. Protection against skin and eye damage is needed.
#define UV_INDEX_VERY_HIGH                  3               // 8 to 10 means very high risk of harm from unprotected sun exposure.
                                                            // Take extra precautions because unprotected skin and eyes will be damaged and can burn quickly.
#define UV_INDEX_EXTREME                    4               // 11 or more means extreme risk of harm from unprotected sun exposure.
                                                            // Take all precautions because unprotected skin and eyes can burn in minutes.

#define SENSOR_PUBLISH_ADDRESSES            0               // Publish sensor addresses
#define SENSOR_ADDRESS_TOPIC                "address"       // Topic to publish sensor addresses

//------------------------------------------------------------------------------
// UNITS
//------------------------------------------------------------------------------

#define POWER_WATTS             0
#define POWER_KILOWATTS         1

#define ENERGY_JOULES           0
#define ENERGY_KWH              1

#define TMP_CELSIUS             0
#define TMP_FAHRENHEIT          1

#ifndef SENSOR_TEMPERATURE_UNITS
#define SENSOR_TEMPERATURE_UNITS            TMP_CELSIUS     // Temperature units (TMP_CELSIUS | TMP_FAHRENHEIT)
#endif

#ifndef SENSOR_ENERGY_UNITS
#define SENSOR_ENERGY_UNITS                 ENERGY_JOULES   // Energy units (ENERGY_JOULES | ENERGY_KWH)
#endif

#ifndef SENSOR_POWER_UNITS
#define SENSOR_POWER_UNITS                  POWER_WATTS     // Power units (POWER_WATTS | POWER_KILOWATTS)
#endif

//--------------------------------------------------------------------------------
// Sensor ID
// These should remain over time, do not modify them, only add new ones at the end
//--------------------------------------------------------------------------------

#define SENSOR_DHTXX_ID                     0x01
#define SENSOR_DALLAS_ID                    0x02
#define SENSOR_EMON_ANALOG_ID               0x03
#define SENSOR_EMON_ADC121_ID               0x04
#define SENSOR_EMON_ADS1X15_ID              0x05
#define SENSOR_HLW8012_ID                   0x06
#define SENSOR_V9261F_ID                    0x07
#define SENSOR_ECH1560_ID                   0x08
#define SENSOR_ANALOG_ID                    0x09
#define SENSOR_DIGITAL_ID                   0x10
#define SENSOR_EVENTS_ID                    0x11
#define SENSOR_PMSX003_ID                   0x12
#define SENSOR_BMX280_ID                    0x13
#define SENSOR_MHZ19_ID                     0x14
#define SENSOR_SI7021_ID                    0x15
#define SENSOR_SHT3X_I2C_ID                 0x16
#define SENSOR_BH1750_ID                    0x17
#define SENSOR_PZEM004T_ID                  0x18
#define SENSOR_AM2320_ID                    0x19
#define SENSOR_GUVAS12SD_ID                 0x20
#define SENSOR_CSE7766_ID                   0x21
#define SENSOR_TMP3X_ID                     0x22

//--------------------------------------------------------------------------------
// Magnitudes
//--------------------------------------------------------------------------------

#define MAGNITUDE_NONE                      0
#define MAGNITUDE_TEMPERATURE               1
#define MAGNITUDE_HUMIDITY                  2
#define MAGNITUDE_PRESSURE                  3
#define MAGNITUDE_CURRENT                   4
#define MAGNITUDE_VOLTAGE                   5
#define MAGNITUDE_POWER_ACTIVE              6
#define MAGNITUDE_POWER_APPARENT            7
#define MAGNITUDE_POWER_REACTIVE            8
#define MAGNITUDE_POWER_FACTOR              9
#define MAGNITUDE_ENERGY                    10
#define MAGNITUDE_ENERGY_DELTA              11
#define MAGNITUDE_ANALOG                    12
#define MAGNITUDE_DIGITAL                   13
#define MAGNITUDE_EVENTS                    14
#define MAGNITUDE_PM1dot0                   15
#define MAGNITUDE_PM2dot5                   16
#define MAGNITUDE_PM10                      17
#define MAGNITUDE_CO2                       18
#define MAGNITUDE_LUX                       19
#define MAGNITUDE_UV                        20

#define MAGNITUDE_MAX                       21

// =============================================================================
// Specific data for each sensor
// =============================================================================

//------------------------------------------------------------------------------
// Analog sensor
// Enable support by passing ANALOG_SUPPORT=1 build flag
//--------------------------------------------------------------------------------

#ifndef ANALOG_SUPPORT
#define ANALOG_SUPPORT                  0
#endif

#if ANALOG_SUPPORT
#undef ADC_VCC_ENABLED
#define ADC_VCC_ENABLED                 0
#endif

//------------------------------------------------------------------------------
// BH1750
// Enable support by passing BH1750_SUPPORT=1 build flag
// http://www.elechouse.com/elechouse/images/product/Digital%20light%20Sensor/bh1750fvi-e.pdf
//------------------------------------------------------------------------------

#ifndef BH1750_SUPPORT
#define BH1750_SUPPORT                  0
#endif

#ifndef BH1750_ADDRESS
#define BH1750_ADDRESS                  0x00    // 0x00 means auto
#endif

#define BH1750_MODE                     BH1750_CONTINUOUS_HIGH_RES_MODE

#if BH1750_SUPPORT
#undef I2C_SUPPORT
#define I2C_SUPPORT                     1
#endif

//------------------------------------------------------------------------------
// BME280/BMP280
// Enable support by passing BMX280_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef BMX280_SUPPORT
#define BMX280_SUPPORT                  0
#endif

#ifndef BMX280_ADDRESS
#define BMX280_ADDRESS                  0x00    // 0x00 means auto
#endif

#define BMX280_MODE                     1       // 0 for sleep mode, 1 or 2 for forced mode, 3 for normal mode
#define BMX280_STANDBY                  0       // 0 for 0.5ms, 1 for 62.5ms, 2 for 125ms
                                                // 3 for 250ms, 4 for 500ms, 5 for 1000ms
                                                // 6 for 10ms, 7 for 20ms
#define BMX280_FILTER                   0       // 0 for OFF, 1 for 2 values, 2 for 4 values, 3 for 8 values and 4 for 16 values
#define BMX280_TEMPERATURE              1       // Oversampling for temperature (set to 0 to disable magnitude)
#define BMX280_HUMIDITY                 1       // Oversampling for humidity (set to 0 to disable magnitude, only for BME280)
#define BMX280_PRESSURE                 1       // Oversampling for pressure (set to 0 to disable magnitude)

#if BMX280_SUPPORT
#undef I2C_SUPPORT
#define I2C_SUPPORT                     1
#endif

//------------------------------------------------------------------------------
// Dallas OneWire temperature sensors
// Enable support by passing DALLAS_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef DALLAS_SUPPORT
#define DALLAS_SUPPORT                  0
#endif

#ifndef DALLAS_PIN
#define DALLAS_PIN                      14
#endif

#define DALLAS_RESOLUTION               9           // Not used atm
#define DALLAS_READ_INTERVAL            2000        // Force sensor read & cache every 2 seconds

//------------------------------------------------------------------------------
// DHTXX temperature/humidity sensor
// Enable support by passing DHT_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef DHT_SUPPORT
#define DHT_SUPPORT                     0
#endif

#ifndef DHT_PIN
#define DHT_PIN                         14
#endif

#ifndef DHT_TYPE
#define DHT_TYPE                        DHT_CHIP_DHT22
#endif

//------------------------------------------------------------------------------
// CSE7766 based power sensor
// Enable support by passing CSE7766_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef CSE7766_SUPPORT
#define CSE7766_SUPPORT                 0
#endif

#ifndef CSE7766_PIN
#define CSE7766_PIN                     1       // TX pin from the CSE7766
#endif

#ifndef CSE7766_PIN_INVERSE
#define CSE7766_PIN_INVERSE             0       // Signal is inverted
#endif

#define CSE7766_SYNC_INTERVAL           300     // Safe time between transmissions (ms)
#define CSE7766_BAUDRATE                4800    // UART baudrate

#define CSE7766_V1R                     1.0     // 1mR current resistor
#define CSE7766_V2R                     1.0     // 1M voltage resistor


//------------------------------------------------------------------------------
// Digital sensor
// Enable support by passing DIGITAL_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef DIGITAL_SUPPORT
#define DIGITAL_SUPPORT                 0
#endif

#ifndef DIGITAL_PIN
#define DIGITAL_PIN                     2
#endif

#ifndef DIGITAL_PIN_MODE
#define DIGITAL_PIN_MODE                INPUT_PULLUP
#endif

#ifndef DIGITAL_DEFAULT_STATE
#define DIGITAL_DEFAULT_STATE           1
#endif

//------------------------------------------------------------------------------
// ECH1560 based power sensor
// Enable support by passing ECH1560_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef ECH1560_SUPPORT
#define ECH1560_SUPPORT                 0
#endif

#ifndef ECH1560_CLK_PIN
#define ECH1560_CLK_PIN                 4       // CLK pin for the ECH1560
#endif

#ifndef ECH1560_MISO_PIN
#define ECH1560_MISO_PIN                5       // MISO pin for the ECH1560
#endif

#ifndef ECH1560_INVERTED
#define ECH1560_INVERTED                0       // Signal is inverted
#endif

//------------------------------------------------------------------------------
// Energy Monitor general settings
//------------------------------------------------------------------------------

#define EMON_MAX_SAMPLES                1000        // Max number of samples to get
#define EMON_MAX_TIME                   250         // Max time in ms to sample
#define EMON_FILTER_SPEED               512         // Mobile average filter speed
#define EMON_MAINS_VOLTAGE              230         // Mains voltage
#define EMON_REFERENCE_VOLTAGE          3.3         // Reference voltage of the ADC
#define EMON_CURRENT_RATIO              30          // Current ratio in the clamp (30V/1A)
#define EMON_REPORT_CURRENT             0           // Report current
#define EMON_REPORT_POWER               1           // Report power
#define EMON_REPORT_ENERGY              1           // Report energy

//------------------------------------------------------------------------------
// Energy Monitor based on ADC121
// Enable support by passing EMON_ADC121_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef EMON_ADC121_SUPPORT
#define EMON_ADC121_SUPPORT             0       // Do not build support by default
#endif

#define EMON_ADC121_I2C_ADDRESS         0x00    // 0x00 means auto

#if EMON_ADC121_SUPPORT
#undef I2C_SUPPORT
#define I2C_SUPPORT                     1
#endif

//------------------------------------------------------------------------------
// Energy Monitor based on ADS1X15
// Enable support by passing EMON_ADS1X15_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef EMON_ADS1X15_SUPPORT
#define EMON_ADS1X15_SUPPORT            0       // Do not build support by default
#endif

#define EMON_ADS1X15_I2C_ADDRESS        0x00    // 0x00 means auto
#define EMON_ADS1X15_TYPE               ADS1X15_CHIP_ADS1115
#define EMON_ADS1X15_GAIN               ADS1X15_REG_CONFIG_PGA_4_096V
#define EMON_ADS1X15_MASK               0x0F    // A0=1 A1=2 A2=4 A3=8

#if EMON_ADS1X15_SUPPORT
#undef I2C_SUPPORT
#define I2C_SUPPORT                     1
#endif

//------------------------------------------------------------------------------
// Energy Monitor based on interval analog GPIO
// Enable support by passing EMON_ANALOG_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef EMON_ANALOG_SUPPORT
#define EMON_ANALOG_SUPPORT             0       // Do not build support by default
#endif

#if EMON_ANALOG_SUPPORT
#undef ADC_VCC_ENABLED
#define ADC_VCC_ENABLED                 0
#endif

//------------------------------------------------------------------------------
// Counter sensor
// Enable support by passing EVENTS_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef EVENTS_SUPPORT
#define EVENTS_SUPPORT                  0       // Do not build with counter support by default
#endif

#ifndef EVENTS_PIN
#define EVENTS_PIN                      2       // GPIO to monitor
#endif

#ifndef EVENTS_PIN_MODE
#define EVENTS_PIN_MODE                 INPUT   // INPUT, INPUT_PULLUP
#endif

#ifndef EVENTS_INTERRUPT_MODE
#define EVENTS_INTERRUPT_MODE           RISING  // RISING, FALLING, BOTH
#endif

#define EVENTS_DEBOUNCE                 50      // Do not register events within less than 10 millis

//------------------------------------------------------------------------------
// HLW8012 Energy monitor IC
// Enable support by passing HLW8012_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef HLW8012_SUPPORT
#define HLW8012_SUPPORT                 0
#endif

#ifndef HLW8012_SEL_PIN
#define HLW8012_SEL_PIN                 5
#endif

#ifndef HLW8012_CF1_PIN
#define HLW8012_CF1_PIN                 13
#endif

#ifndef HLW8012_CF_PIN
#define HLW8012_CF_PIN                  14
#endif

#ifndef HLW8012_SEL_CURRENT
#define HLW8012_SEL_CURRENT             HIGH    // SEL pin to HIGH to measure current
#endif

#ifndef HLW8012_CURRENT_R
#define HLW8012_CURRENT_R               0.001   // Current resistor
#endif

#ifndef HLW8012_VOLTAGE_R_UP
#define HLW8012_VOLTAGE_R_UP            ( 5 * 470000 )  // Upstream voltage resistor
#endif

#ifndef HLW8012_VOLTAGE_R_DOWN
#define HLW8012_VOLTAGE_R_DOWN          ( 1000 )        // Downstream voltage resistor
#endif

#define HLW8012_USE_INTERRUPTS          1       // Use interrupts to trap HLW8012 signals

//------------------------------------------------------------------------------
// MHZ19 CO2 sensor
// Enable support by passing MHZ19_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef MHZ19_SUPPORT
#define MHZ19_SUPPORT                   0
#endif

#define MHZ19_RX_PIN                    13
#define MHZ19_TX_PIN                    15

//------------------------------------------------------------------------------
// Particle Monitor based on Plantower PMSX003
// Enable support by passing PMSX003_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef PMSX003_SUPPORT
#define PMSX003_SUPPORT                 0
#endif

#define PMS_RX_PIN                      13
#define PMS_TX_PIN                      15

//------------------------------------------------------------------------------
// PZEM004T based power monitor
// Enable support by passing PZEM004T_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef PZEM004T_SUPPORT
#define PZEM004T_SUPPORT                0
#endif

#ifndef PZEM004T_USE_SOFT
#define PZEM004T_USE_SOFT               1       // Use software serial
#endif

#ifndef PZEM004T_RX_PIN
#define PZEM004T_RX_PIN                 13      // Software serial RX GPIO (if PZEM004T_USE_SOFT == 1)
#endif

#ifndef PZEM004T_TX_PIN
#define PZEM004T_TX_PIN                 15      // Software serial TX GPIO (if PZEM004T_USE_SOFT == 1)
#endif

#ifndef PZEM004T_HW_PORT
#define PZEM004T_HW_PORT                Serial1 // Hardware serial port (if PZEM004T_USE_SOFT == 0)
#endif


//------------------------------------------------------------------------------
// SHT3X I2C (Wemos) temperature & humidity sensor
// Enable support by passing SHT3X_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef SHT3X_I2C_SUPPORT
#define SHT3X_I2C_SUPPORT               0
#endif

#ifndef SHT3X_I2C_ADDRESS
#define SHT3X_I2C_ADDRESS               0x00    // 0x00 means auto
#endif

#if SHT3X_I2C_SUPPORT
#undef I2C_SUPPORT
#define I2C_SUPPORT                     1
#endif

//------------------------------------------------------------------------------
// SI7021 temperature & humidity sensor
// Enable support by passing SI7021_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef SI7021_SUPPORT
#define SI7021_SUPPORT                  0
#endif

#ifndef SI7021_ADDRESS
#define SI7021_ADDRESS                  0x00    // 0x00 means auto
#endif

#if SI7021_SUPPORT
#undef I2C_SUPPORT
#define I2C_SUPPORT                     1
#endif

//------------------------------------------------------------------------------
// TMP3X analog temperature sensor
// Enable support by passing TMP3X_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef TMP3X_SUPPORT
#define TMP3X_SUPPORT                   0
#endif

#ifndef TMP3X_TYPE
#define TMP3X_TYPE                      TMP3X_TMP35
#endif

#if TMP3X_SUPPORT
#undef ADC_VCC_ENABLED
#define ADC_VCC_ENABLED                 0
#endif

//------------------------------------------------------------------------------
// V9261F based power sensor
// Enable support by passing SI7021_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef V9261F_SUPPORT
#define V9261F_SUPPORT                  0
#endif

#ifndef V9261F_PIN
#define V9261F_PIN                      2       // TX pin from the V9261F
#endif

#ifndef V9261F_PIN_INVERSE
#define V9261F_PIN_INVERSE              1       // Signal is inverted
#endif

#define V9261F_SYNC_INTERVAL            600     // Sync signal length (ms)
#define V9261F_BAUDRATE                 4800    // UART baudrate

// Default ratios
#define V9261F_CURRENT_FACTOR           79371434.0
#define V9261F_VOLTAGE_FACTOR           4160651.0
#define V9261F_POWER_FACTOR             153699.0
#define V9261F_RPOWER_FACTOR            V9261F_CURRENT_FACTOR

//------------------------------------------------------------------------------
// AM2320 Humidity & Temperature sensor over I2C
// Enable support by passing AM2320_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef AM2320_SUPPORT
#define AM2320_SUPPORT                  0
#endif

#ifndef AM2320_ADDRESS
#define AM2320_ADDRESS                  0x00    // 0x00 means auto
#endif

#if AM2320_SUPPORT
#undef I2C_SUPPORT
#define I2C_SUPPORT                     1
#endif

//------------------------------------------------------------------------------
// GUVAS12SD UV Sensor (analog)
// Enable support by passing GUVAS12SD_SUPPORT=1 build flag
//------------------------------------------------------------------------------

#ifndef GUVAS12SD_SUPPORT
#define GUVAS12SD_SUPPORT               0
#endif

#ifndef GUVAS12SD_PIN
#define GUVAS12SD_PIN                   14
#endif

// =============================================================================
// Sensor helpers configuration
// =============================================================================

#ifndef SENSOR_SUPPORT
#if ANALOG_SUPPORT || BH1750_SUPPORT || BMX280_SUPPORT || DALLAS_SUPPORT \
    || DHT_SUPPORT || DIGITAL_SUPPORT || ECH1560_SUPPORT \
    || EMON_ADC121_SUPPORT || EMON_ADS1X15_SUPPORT \
    || EMON_ANALOG_SUPPORT || EVENTS_SUPPORT || HLW8012_SUPPORT \
    || MHZ19_SUPPORT || PMSX003_SUPPORT || SHT3X_I2C_SUPPORT \
    || SI7021_SUPPORT || V9261F_SUPPORT || AM2320_SUPPORT \
    || GUVAS12SD_SUPPORT || CSE7766_SUPPORT || TMP3X_SUPPORT
#define SENSOR_SUPPORT                      1
#else
#define SENSOR_SUPPORT                      0
#endif
#endif

// -----------------------------------------------------------------------------
// I2C
// -----------------------------------------------------------------------------

#ifndef I2C_SUPPORT
#define I2C_SUPPORT                     0       // I2C enabled (1.98Kb)
#endif

#define I2C_USE_BRZO                    0       // Use brzo_i2c library or standard Wire

#ifndef I2C_SDA_PIN
#define I2C_SDA_PIN                     SDA     // SDA GPIO (Sonoff => 4)
#endif

#ifndef I2C_SCL_PIN
#define I2C_SCL_PIN                     SCL     // SCL GPIO (Sonoff => 14)
#endif

#define I2C_CLOCK_STRETCH_TIME          200     // BRZO clock stretch time
#define I2C_SCL_FREQUENCY               1000    // BRZO SCL frequency
#define I2C_CLEAR_BUS                   0       // Clear I2C bus on boot
#define I2C_PERFORM_SCAN                1       // Perform a bus scan on boot

//--------------------------------------------------------------------------------
// Internal power monitor
// Enable support by passing ADC_VCC_ENABLED=1 build flag
// Do not enable this if using the analog GPIO for any other thing
//--------------------------------------------------------------------------------

#ifndef ADC_VCC_ENABLED
#define ADC_VCC_ENABLED                 1
#endif

#if ADC_VCC_ENABLED
    ADC_MODE(ADC_VCC);
#endif

//--------------------------------------------------------------------------------
// Class loading
//--------------------------------------------------------------------------------

#if SENSOR_SUPPORT

PROGMEM const unsigned char magnitude_decimals[] = {
    0,
    1, 0, 2,
    3, 0, 0, 0, 0, 0, 0, 0,
    0, 0, 0,
    0, 0, 0,
    0, 0
};

PROGMEM const char magnitude_unknown_topic[] = "unknown";
PROGMEM const char magnitude_temperature_topic[] =  "temperature";
PROGMEM const char magnitude_humidity_topic[] = "humidity";
PROGMEM const char magnitude_pressure_topic[] = "pressure";
PROGMEM const char magnitude_current_topic[] = "current";
PROGMEM const char magnitude_voltage_topic[] = "voltage";
PROGMEM const char magnitude_active_power_topic[] = "power";
PROGMEM const char magnitude_apparent_power_topic[] = "apparent";
PROGMEM const char magnitude_reactive_power_topic[] = "reactive";
PROGMEM const char magnitude_power_factor_topic[] = "factor";
PROGMEM const char magnitude_energy_topic[] = "energy";
PROGMEM const char magnitude_energy_delta_topic[] = "energy_delta";
PROGMEM const char magnitude_analog_topic[] = "analog";
PROGMEM const char magnitude_digital_topic[] = "digital";
PROGMEM const char magnitude_events_topic[] = "events";
PROGMEM const char magnitude_pm1dot0_topic[] = "pm1dot0";
PROGMEM const char magnitude_pm2dot5_topic[] = "pm2dot5";
PROGMEM const char magnitude_pm10_topic[] = "pm10";
PROGMEM const char magnitude_co2_topic[] = "co2";
PROGMEM const char magnitude_lux_topic[] = "lux";
PROGMEM const char magnitude_uv_topic[] = "uv";

PROGMEM const char* const magnitude_topics[] = {
    magnitude_unknown_topic, magnitude_temperature_topic, magnitude_humidity_topic,
    magnitude_pressure_topic, magnitude_current_topic, magnitude_voltage_topic,
    magnitude_active_power_topic, magnitude_apparent_power_topic, magnitude_reactive_power_topic,
    magnitude_power_factor_topic, magnitude_energy_topic, magnitude_energy_delta_topic,
    magnitude_analog_topic, magnitude_digital_topic, magnitude_events_topic,
    magnitude_pm1dot0_topic, magnitude_pm2dot5_topic, magnitude_pm10_topic,
    magnitude_co2_topic, magnitude_lux_topic, magnitude_uv_topic
};

PROGMEM const char magnitude_empty[] = "";
PROGMEM const char magnitude_celsius[] =  "C";
PROGMEM const char magnitude_fahrenheit[] =  "F";
PROGMEM const char magnitude_percentage[] = "%";
PROGMEM const char magnitude_hectopascals[] = "hPa";
PROGMEM const char magnitude_amperes[] = "A";
PROGMEM const char magnitude_volts[] = "V";
PROGMEM const char magnitude_watts[] = "W";
PROGMEM const char magnitude_kw[] = "kW";
PROGMEM const char magnitude_joules[] = "J";
PROGMEM const char magnitude_kwh[] = "kWh";
PROGMEM const char magnitude_ugm3[] = "µg/m3";
PROGMEM const char magnitude_ppm[] = "ppm";
PROGMEM const char magnitude_lux[] = "lux";
PROGMEM const char magnitude_uv[] = "uv";

PROGMEM const char* const magnitude_units[] = {
    magnitude_empty, magnitude_celsius, magnitude_percentage,
    magnitude_hectopascals, magnitude_amperes, magnitude_volts,
    magnitude_watts, magnitude_watts, magnitude_watts,
    magnitude_percentage, magnitude_joules, magnitude_joules,
    magnitude_empty, magnitude_empty, magnitude_empty,
    magnitude_ugm3, magnitude_ugm3, magnitude_ugm3,
    magnitude_ppm, magnitude_lux, magnitude_uv
};

#include "../sensors/BaseSensor.h"

#if AM2320_SUPPORT
    #include "../sensors/AM2320Sensor.h"
#endif

#if ANALOG_SUPPORT
    #include "../sensors/AnalogSensor.h"
#endif

#if BH1750_SUPPORT
    #include "../sensors/BH1750Sensor.h"
#endif

#if BMX280_SUPPORT
    #include "../sensors/BMX280Sensor.h"
#endif

#if CSE7766_SUPPORT
    #include <SoftwareSerial.h>
    #include "../sensors/CSE7766Sensor.h"
#endif

#if DALLAS_SUPPORT
    #include <OneWire.h>
    #include "../sensors/DallasSensor.h"
#endif

#if DHT_SUPPORT
    #include "../sensors/DHTSensor.h"
#endif

#if DIGITAL_SUPPORT
    #include "../sensors/DigitalSensor.h"
#endif

#if ECH1560_SUPPORT
    #include "../sensors/ECH1560Sensor.h"
#endif

#if EMON_ADC121_SUPPORT
    #include "../sensors/EmonADC121Sensor.h"
#endif

#if EMON_ADS1X15_SUPPORT
    #include "../sensors/EmonADS1X15Sensor.h"
#endif

#if EMON_ANALOG_SUPPORT
    #include "../sensors/EmonAnalogSensor.h"
#endif

#if EVENTS_SUPPORT
    #include "../sensors/EventSensor.h"
#endif

#if GUVAS12SD_SUPPORT
    #include "../sensors/GUVAS12SDSensor.h"
#endif

#if HLW8012_SUPPORT
    #include <HLW8012.h>
    #include "../sensors/HLW8012Sensor.h"
#endif

#if MHZ19_SUPPORT
    #include <SoftwareSerial.h>
    #include "../sensors/MHZ19Sensor.h"
#endif

#if PMSX003_SUPPORT
    #include <SoftwareSerial.h>
    #include <PMS.h>
    #include "../sensors/PMSX003Sensor.h"
#endif

#if PZEM004T_SUPPORT
    #include <SoftwareSerial.h>
    #include "../sensors/PZEM004TSensor.h"
#endif

#if SI7021_SUPPORT
    #include "../sensors/SI7021Sensor.h"
#endif

#if SHT3X_I2C_SUPPORT
    #include "../sensors/SHT3XI2CSensor.h"
#endif

#if TMP3X_SUPPORT
    #include "../sensors/TMP3XSensor.h"
#endif

#if V9261F_SUPPORT
    #include <SoftwareSerial.h>
    #include "../sensors/V9261FSensor.h"
#endif

#endif // SENSOR_SUPPORT