* Add support for Benexmart GU5.3 RGBWW light

* Update arduino.h

Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>

* Add support for LSC E27 10W white bulb

* Add OTA config for LSC E27 10W white bulb
Add LSC E27 10W white bulb to arduino.h

Device in question: https://www.aliexpress.com/item/32925895199.html
Named after print on the PCB.

Co-authored-by: user176176 <>

* Add support for the Zhilde ZLD-64EU-W

This is a power outlet with 6 power sockets and 4 USB ports.

* fixup based on the zld-44eu hw and tasmota template info

Co-authored-by: Maxim Prokhorov <prokhorov.max@outlook.com>

- RF_... -> RFB_...
- rework rcswitch integration, support variable length payload
- rework rfbridge parser (not tested)
- rework settings scanning routine when trying to match rf payload
  with the relay ID
- update build tests

Add support for BME680 using libalgobsec proprietary algorithms for precise Indoor Air Quality (IAQ) measurement. Unlike traditional CO2 sensors - and good ones are expensive - it measures nearly all VOCs compounds in the air (plus other gases) and compensates those measurements with its built-in temperature and humidity sensors to determine indoor air quality.

Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>

- implement mcp23s08
- support mcp pins in relays and buttons
- add hardware profile for ProDino WiFi

Co-authored-by: dpeddi <dpeddi@gmail.com>
Co-authored-by: Maxim Prokhorov <prokhorov.max@outlook.com>

* hardware: Add support for HUGOAI smart socket plug.

* Update code/platformio.ini

Co-authored-by: pezinek <pezinek@gmail.com>

Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
Co-authored-by: pezinek <pezinek@gmail.com>

This will add support for the KingArt Wifi Curtain Switch. There are no buttons in the web interface as I could not figure out how to create them (any help on that is welcome).

For now the switch can be controlled over MQTT:
"{hostname}/curtain/set"
"{hostname}/curtain"

* hardware: Add support for Aoycocr X5P Plug.

This change allow espurna to control Aoycocr X5P Plug devices, which has
the same behaviour as the GOSUND WP3 but using different GPIO pins for
relay, button and leds.

* Update platformio.ini

Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>

* ADC_VCC is not macro

* In esp.h ADC_VCC and ADC_TOUT is not macro, so define macro.

* ADC_VCC and ADC_TOUT fixes in utils.ino and sensors.h

* Adding support for I2C temperature and humidity sensor HDC1080 / 831R

* Added HDC1080 to test\build\sensor.h and arduino.h

* added brackets

* Revert ADC_MODE_VALUE to initial values

* Eof newline

* Eof newline

Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>

* update platformio.ini comments
* espurna-base -> espurna-core-webui
* esp8266-<flavour>-<size>-base -> esp8266-<size>-<flavour>-base
* clean-up ESPURNA_CORE detection, use boards function

Co-authored-by: ziggurat29 <xxx@yyy.zzz>

Co-authored-by: ziggurat29 <xxx@yyy.zzz>

* Config: remove prototypes.h

* fixup order

* word

* add missing

* fix warning while still using .ino

* bad at c/p;

* PIO: remove -ota envs, handle OTA condition in extra script
* Tweak ESPURNA_BOARD variable
* Support git and latest in ota script
* Handle ESPURNA_FLAGS too
* Try to handle env and projenv in pylint
* Add deprecation comment about -ota envs
* regen arduino.h

Not a match to same model from Neo Coolcam

* add support for DELTACO SH-P01

* renaming deltaco_sh_le14w to deltaco_sh_lexxw

* add support Deltaco SH-P03USB and SH-LEXXRGB

* Add support for Kogan Smarter Home Plug With Energy Meter

Type: Power Plug
Board: Kogan Smarter Home Plug with Energy Meter
Build flag: KOGAN_SMARTER_HOME_PLUG_W_POW
Description: Power Plug with integrated Energy Meter
Baseboard: Tuya TYWE3S
Baseboard Data sheet: https://docs.tuya.com/docDetail?code=K8uhkbb1ihp8u

* Include Kogan Smarter Home plug with energy meter (KOGAN_SMARTER_HOME_PLUG_W_POW) into arduino.h

* Update platformio.ini to support Kogan Smarter Home plug with energy meter (KOGAN_SMARTER_HOME_PLUG_W_POW)

* Add Kogan Smarter Home plug with energy meter product image

* fix platformio.ini that was missing a '-ota' for the environment

* comment out device definition

* Make device name consistent with #define and platformio.ini

We have created a few dozens of devices, released as open-source hardware and
published the schematics to GitHub. We're planning to organize some small
(10-15 people) workshops on how to assemble, flash and configure these board.

https://github.com/eHomeDIY

* Add LinkSprite R4 def

* Platformio.ini def for linksprite r4

* LINKSPRITE_LINKNODE_R4

- fix hardware.h weird encoding (todo: is there a git-attribute for
this to be peristent?)
- sort and add missing support and hw entries to the arduino.h
- force thermostat to depend on sensors to avoid confusing linker error

* add support for Hykker Smart Plug with power meter
Type: Power Plugs
Board: Hykker Power Plug
Build flag: HYKKER_POWER_PLUG
Description: Power plug w/ power metering

* Update arduino.h

hykker power plug

* Update platformio.ini

hykker power plug

* Type: Power Plugs
Board: Hykker Smart Home Power Plug
Build flag: HYKKER_SMART_HOME_POWER_PLUG
Description: Power plug w/ power metering

* voltage ratio calibration for correct results

* scripts: memanalyzer fixes

- cleanup duplication
- cleanup external dependencies
- properly use subprocess when calling pio, add debug mode
- cleanup argparse usage, use store_true actions instead of counters
- use python3 syntax and python3 shebang by default
- fix some issues with module dependencies

* move to scripts

* use simple return

* quick fix for rfm

* codacy unused import

* formatting

* show defaults

* while at it, rewrite to make pylint happy

* fix unused

* add windows support + note

* RPN rules (WIP)

* RPN rules web interface, MQTT inputs

* Stickyness, rpn.ops,...

* Perform light updates only when value changes

* Improve wsSend performance

* Revert PR test

* Check TERMINAL_SUPPORT for _rpnInitCommands and remove unused variable

* Fix merge

* formatting

* disable by default (?)

* changelog

* comment

* remove debug function wrappers in favour of var activation

* fixup! comment

* Adding support for miobulb001

* Add miobulb001 images

* defined MUVIT_IO_MIOBULB001

* Update platformio.ini

revert default env
use dashes

* typo

* typo

* Added T6613

* Added T6613

* Added T6613

* Added T6613

* Added T6613

* Added T6613

* Added T6613

* Added T6613

* Added T6613

* Updated copyright string

* Buffer from 6 bytes to 8 bytes

Current gcc-4 does not mark this as warning, but gcc-9 notices the 3 char size requirement. Buffer should be 8

* Use 5000ppm max

Control board for Hoermann UAP1 Garage interface
http://frank-schuetz.de/index.php/fhem/13-hoermann-torantrieb-mit-espeasy-in-fhem-einbinden

* Add Shelly 2.5

* Add ADE7953 sensor support

* Fix compilation

* Use only one instance

* WIP: Not working, I got StoreProhibited exception

* Fix exception

* Fix merge issues

* Apply request review changes

* declare struct before using it

* uninterruptible delay

* try optimized reg_size

* fix types

* Remove gpio 0 input in analog sensor

* Add energy to ADE7953, it is not finished yet

* Add new method to save energy with index

* Finish energy for ADE7953

* Add Shelly 1PM

* Improve Shelly 1PM temperature tabs

* Add shelly 1pm button

* adding Nexete

Started Adding Nexete A19 Bulb

* Update hardware.h

* fixed pinout

* Rename to Nexete_A19 + added non-ota

* Add support for MagicHome RGBWW LED strip

This adds support for MagicHome 5 channel LED strip. It is using ESP8285 board, labelled as ESP-M4, has 5 powerful MOSFETs (M3006D, up to 80A! continuous/160A peak) at 12-24V. They are driven by smaller transistors. Red LED is connected to 3.3V power supply, and can't be controller. Green LED is connected to GPIO. Pin mappings:
BTN IO0
R Q8 Q2 IO14
G Q6 Q3 IO12
B Q9 Q4 IO13
WW Q10 Q5 IO15
CW Q7 Q1 IO5
GREEN_LED IO2
Looks like the same board is used in another product which has support for RF remote, but mine doesn't, so I don't include RF config, if yours has it should be a simple copy/paste job to add it.

* Add config for push button

* Fix copy/paste mistake

* Turn on/off LEDs using the push button