Add support for BME680 using libalgobsec proprietary algorithms for precise Indoor Air Quality (IAQ) measurement. Unlike traditional CO2 sensors - and good ones are expensive - it measures nearly all VOCs compounds in the air (plus other gases) and compensates those measurements with its built-in temperature and humidity sensors to determine indoor air quality.
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
Add new V3.0 version of PZEM004T, not tested. Default to factory default address 0xf8, configurable through pzemv30Addr 8-bit number
Add 'frequency' measurement & 'hz' unit
Add pz.address that configures address
Implemented energy reset
Right now we only support a single device. No way to test this properly (mostly, how exactly we need to connect this stuff), so left as not implemented.
Change the underlying command line handling:
- switch to a custom parser, inspired by redis / sds
- update terminalRegisterCommand signature, pass only bare minimum
- clean-up `help` & `commands`. update settings `set`, `get` and `del`
- allow our custom test suite to run command-line tests
- clean-up Stream IO to allow us to print large things into debug stream (for example, `eeprom.dump`)
- send parsing errors to the debug log
As a proof of concept, introduce `TERMINAL_MQTT_SUPPORT` and `TERMINAL_WEB_API_SUPPORT`
- MQTT subscribes to the `<root>/cmd/set` and sends response to the `<root>/cmd`. We can't output too much, as we don't have any large-send API.
- Web API listens to the `/api/cmd?apikey=...&line=...` (or PUT, params inside the body). This one is intended as a possible replacement of the `API_SUPPORT`. Internals introduce a 'task' around the AsyncWebServerRequest object that will simulate what WiFiClient does and push data into it continuously, switching between CONT and SYS.
Both are experimental. We only accept a single command and not every command is updated to use Print `ctx.output` object. We are also somewhat limited by the Print / Stream overall, perhaps I am overestimating the usefulness of Arduino compatibility to such an extent :)
Web API handler can also sometimes show only part of the result, whenever the command tries to yield() by itself waiting for something. Perhaps we would need to create a custom request handler for that specific use-case.
This will add support for the KingArt Wifi Curtain Switch. There are no buttons in the web interface as I could not figure out how to create them (any help on that is welcome).
For now the switch can be controlled over MQTT:
"{hostname}/curtain/set"
"{hostname}/curtain"
* ADC_VCC is not macro
* In esp.h ADC_VCC and ADC_TOUT is not macro, so define macro.
* ADC_VCC and ADC_TOUT fixes in utils.ino and sensors.h
* Adding support for I2C temperature and humidity sensor HDC1080 / 831R
* Added HDC1080 to test\build\sensor.h and arduino.h
* added brackets
* Revert ADC_MODE_VALUE to initial values
* Eof newline
* Eof newline
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
* Sensors: refactor configuration
- move sensor implementaion to the .ino,
remove dependency undef / define from sensor files
- update test/build/sensor.h from SENSOR_SUPPORT
- allow to change sensor config variables externally
- `#include <...>` for global headers and libraries,
fix relative path for math library
* add missing sns <-> i2c dependency
* ledrelay should return relay_none as default
* rollback to original test header
* include debug header when requested (relative)
- add experimental `relayDummy` to configure dummy relays at runtime
- add tuya-generic-dimmer #1729
- cleanup broker interface to allow Tuya module to properly receive events, modify broker methods to allow different function signatures
- add basic tests for Tuya frame and data protocol
* Use generic typechecks, OTA add followRedirects
* revamp using is_detected
* relative include
* mention ts draft instead, fix c++17 includes (still not buildable)
* typo
* Always create WiFiClient pointer
* Remove old CREATE_CHECK macro
* do not create wificlient obj when running old Core
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Updated copyright string
* Buffer from 6 bytes to 8 bytes
Current gcc-4 does not mark this as warning, but gcc-9 notices the 3 char size requirement. Buffer should be 8
* Use 5000ppm max
* travis: move build flags tests outside of hardware header
* mqtt: fix typo
* travis: use files instead of bundling test cases into script
* fixup! travis: use files instead of bundling test cases into script
* fix variable expansion, remove custom h at the end
* add ade7953 to sensors list
* custom.h path as variable
* shellcheck
* fix printf syntax, silent again
* fix bash 4.3 treating empty array as unset variable
Maxim Prokhorov
Rui Marinho
Albert Weterings
Alexander
Niek van der Maas
James