Make sure 'custom provider' `lightAdd()` scheduled function locks further channel modifications,
and take care of light sanity checks before the light update is even scheduled.
Reworked rtcmem reader / writer to use default values, instead of accidentaly using
the unitialized mem of the stack. Also, reworked const names used by the lights module
to distinguish them from the build flags.
- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve#2222
* broker: declare and define per module
We no longer need to specify each Broker type in broker.h
But, we exchange that bit for explicit initialization of the instance
Define helper macros to generate boilerplate code
- namespace with Instance, Register(), Publish()
- forward Register(...) -> Instance.Register(...),
Publish(...) -> Instance.Publish(...)
* don't check for broker when deps enable it
- general conversion from .ino modules into a separate .cpp files
- clean-up internal headers, place libraries into .h. guard .cpp with _SUPPORT flags
- fix some instances of shared variables instead of public methods
- tweak build system to still build a single source file via os environment variable ESPURNA_BUILD_SINGLE_SOURCE
* hlw8012: load hardware-specific ratios
* hlw8012: read energy in pre() callback
* dcz: nvalue should be integer
* sns: fix pressure constrain
* sns: load ratios based on index too
* sns: per-magnitude corrections (still limited by type)
* sns: attach units to index
- Domoticz only accepts svalue <pressure>;<forecast>,
failing to display anything otherwise.
We don't have any forecast calculation (yet?), simply send dummy value.
- Move Domoticz code outside of sensor.ino
- mask is defined as (relay# status << number)
- transparently handle base-2 and base-10 numbers
- if the relay mode requires us to save the mask, it will be saved as base-2
- add experimental `relayDummy` to configure dummy relays at runtime
- add tuya-generic-dimmer #1729
- cleanup broker interface to allow Tuya module to properly receive events, modify broker methods to allow different function signatures
- add basic tests for Tuya frame and data protocol
* Light: proper printf format for HSV, use lround
* core: warn about map() and 2.3.0, type-strict constrain()
* use generic format
* value already has brightness
- update every dynamicjsonbuffer with fixed size constructor argument
- change to ws callback registration to use a class builder (just cosmetic)
- test multiple ws data callbacks for each module
- remove some of the static strings in favour of ws data callback
- improve sensor ws callback data size, remove duplicated strings
- use static buffer in wsDebugSend
- postpone wsSend until loop, implement wsPost to allow other modules to queue message callbacks. remove Ticker based ws callbacks for data
- update WebUI files
* send all ws config at once on start
* reduce ws json overhead by creating message buffer manually
* use k:[values] instead of k1:value1, k2:value2 etc. for lists
Maxim Prokhorov
mkozlowski
m-kozlowski
dpeddi
Malachi Soord
moi
Xose Pérez
sq5gvm