|
|
- /*
- ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
- Licensed under the Apache License, Version 2.0 (the "License");
- you may not use this file except in compliance with the License.
- You may obtain a copy of the License at
-
- http://www.apache.org/licenses/LICENSE-2.0
-
- Unless required by applicable law or agreed to in writing, software
- distributed under the License is distributed on an "AS IS" BASIS,
- WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- See the License for the specific language governing permissions and
- limitations under the License.
- */
-
- #ifndef _BOARD_H_
- #define _BOARD_H_
-
- /*
- * Board identifier.
- */
- #define BOARD_JM60
- #define BOARD_NAME "ErgoDox STM32 Keyboard"
-
- /*
- * Board frequencies.
- */
- #define STM32_LSECLK 0
- #define STM32_HSECLK 8000000
-
- /*
- * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
- *
- * Only xB (128KB Flash) is defined, but it's identical to the
- * x8 version (64KB Flash) except for the Flash region size in the
- * linker script. For x8 parts use xB here and change to the x8 linker
- * script in the project Makefile.
- */
- #define STM32F103xB
-
- /*
- * IO pins assignments
- *
- * numbering is sorted by onboard/connectors, as from the schematics in
- * http://www.vcc-gnd.com/read.php?tid=369
- */
-
- /* on-board */
- #define GPIOA_USBDM 11 // pin 8
- #define GPIOA_USBDP 12 // pin 9
-
- #define GPIOC_OSC32_IN 14
- #define GPIOC_OSC32_OUT 15
-
- /*
- * I/O ports initial setup, this configuration is established soon after reset
- * in the initialization code.
- *
- * The digits have the following meaning:
- * 0 - Analog input.
- * 1 - Push Pull output 10MHz.
- * 2 - Push Pull output 2MHz.
- * 3 - Push Pull output 50MHz.
- * 4 - Digital input.
- * 5 - Open Drain output 10MHz.
- * 6 - Open Drain output 2MHz.
- * 7 - Open Drain output 50MHz.
- * 8 - Digital input with PullUp or PullDown resistor depending on ODR.
- * 9 - Alternate Push Pull output 10MHz.
- * A - Alternate Push Pull output 2MHz.
- * B - Alternate Push Pull output 50MHz.
- * C - Reserved.
- * D - Alternate Open Drain output 10MHz.
- * E - Alternate Open Drain output 2MHz.
- * F - Alternate Open Drain output 50MHz.
- * Please refer to the STM32 Reference Manual for details.
- */
-
- /*
- * Port A setup.
- * Everything input with pull-up except:
- */
- #define VAL_GPIOACRL 0x88888888 /* PA7...PA0 */
- #define VAL_GPIOACRH 0x88888888 /* PA15...PA8 */
- #define VAL_GPIOAODR 0xFFFFFFFF
-
- /*
- * Port B setup.
- * Everything input with pull-up except:
- */
- #define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
- #define VAL_GPIOBCRH 0x88888888 /* PB15...PB8 */
- #define VAL_GPIOBODR 0xFFFFFFFF
-
- /*
- * Port C setup.
- * Everything input with pull-up except:
- */
- #define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
- #define VAL_GPIOCCRH 0x88888888 /* PC15...PC8 */
- #define VAL_GPIOCODR 0xFFFFFFFF
-
- /*
- * Port D setup.
- * Everything input with pull-up except:
- * PD0 - Normal input (XTAL).
- * PD1 - Normal input (XTAL).
- */
- #define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
- #define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
- #define VAL_GPIODODR 0xFFFFFFFF
-
- /*
- * Port E setup.
- * Everything input with pull-up except:
- */
- #define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
- #define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
- #define VAL_GPIOEODR 0xFFFFFFFF
-
- /*
- * USB bus activation macro, required by the USB driver.
- */
- #define usb_lld_connect_bus(usbp) /* always connected */
-
- /*
- * USB bus de-activation macro, required by the USB driver.
- */
- #define usb_lld_disconnect_bus(usbp) /* always connected */
-
- #if !defined(_FROM_ASM_)
- #ifdef __cplusplus
- extern "C" {
- #endif
- void boardInit(void);
- #ifdef __cplusplus
- }
- #endif
- #endif /* _FROM_ASM_ */
-
- #endif /* _BOARD_H_ */
|