@ -0,0 +1,45 @@ | |||
#ifndef CONFIG_H | |||
#define CONFIG_H | |||
#include "config_common.h" | |||
/* USB Device descriptor parameter */ | |||
#define VENDOR_ID 0xBB80 | |||
#define PRODUCT_ID 0x050D | |||
#define DEVICE_VER 0x0001 | |||
#define MANUFACTURER Maartenwut | |||
#define PRODUCT Ortho | |||
#define DESCRIPTION Handwired ortholinear keyboard | |||
/* key matrix size */ | |||
#define MATRIX_ROWS 5 | |||
#define MATRIX_COLS 14 | |||
/* | |||
* Keyboard Matrix Assignments | |||
* | |||
* Change this to how you wired your keyboard | |||
* COLS: AVR pins used for columns, left to right | |||
* ROWS: AVR pins used for rows, top to bottom | |||
* DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) | |||
* ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) | |||
* | |||
*/ | |||
#define MATRIX_ROW_PINS { D4, D0, D1, D2, D3 } | |||
#define MATRIX_COL_PINS { C6, D7, E6, B4, B5, B6, B7, D6, F0, F1, F4, F5, F6, F7 } | |||
#define UNUSED_PINS | |||
/* COL2ROW or ROW2COL */ | |||
#define DIODE_DIRECTION COL2ROW | |||
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ | |||
#define DEBOUNCING_DELAY 5 | |||
/* key combination for magic key command */ | |||
#define IS_COMMAND() ( \ | |||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ | |||
) | |||
#define QMK_ESC_OUTPUT C6 // usually COL | |||
#define QMK_ESC_INPUT D0 // usually ROW | |||
#endif |
@ -0,0 +1,46 @@ | |||
#include "maartenwut.h" | |||
#define _MA 0 | |||
#define _NU 1 | |||
#define _FL 2 | |||
#define _GA 3 | |||
#define _AR 4 | |||
#define _______ KC_TRNS | |||
#define XXXXXXX KC_NO | |||
#define LSHIFT OSM(MOD_LSFT) | |||
#define SPACE LT(_AR, KC_SPC) | |||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
[_MA] = KEYMAP( | |||
KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, | |||
KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, | |||
KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_DEL, KC_ENT, | |||
LSHIFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_UP, KC_PSCR, | |||
KC_LCTL, KC_LGUI, KC_LALT, MO(_NU), SPACE, KC_SPC, MO(_FL), KC_RALT, KC_LEFT, KC_DOWN, KC_RGHT), | |||
[_NU] = KEYMAP( | |||
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, KC_7, KC_8, KC_9, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
KC_CAPS, KC_4, KC_5, KC_6, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, KC_1, KC_2, KC_3, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, KC_0, _______, _______, _______, _______, _______, _______, _______, _______, _______), | |||
[_FL] = KEYMAP( | |||
_______, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_MPLY, | |||
RESET, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, _______, _______, _______, _______, TG(_GA), _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______), | |||
[_GA] = KEYMAP( | |||
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
KC_LSFT, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, _______, _______, _______, KC_SPC, _______, _______, _______, _______, _______, _______), | |||
[_AR] = KEYMAP( | |||
_______, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, _______, | |||
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, | |||
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______) | |||
}; |
@ -0,0 +1,13 @@ | |||
#include "maartenwut.h" | |||
void matrix_init_kb(void) { | |||
// put your keyboard start-up code here | |||
// runs once when the firmware starts up | |||
matrix_init_user(); | |||
} | |||
void matrix_scan_kb(void) { | |||
// put your looping keyboard code here | |||
// runs every cycle (a lot) | |||
matrix_scan_user(); | |||
}; |
@ -0,0 +1,23 @@ | |||
#ifndef MAARTENWUT_H | |||
#define MAARTENWUT_H | |||
#include "quantum.h" | |||
#define XXX KC_NO | |||
#define KEYMAP( \ | |||
k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, \ | |||
k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d, \ | |||
k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k2d, \ | |||
k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c, k3d, \ | |||
k40, k41, k42, k43, k45, k47, k49, k4a, k4b, k4c, k4d \ | |||
) \ | |||
{ \ | |||
{k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d}, \ | |||
{k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d}, \ | |||
{k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k2d}, \ | |||
{k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c, k3d}, \ | |||
{k40, k41, k42, k43, XXX, k45, XXX, k47, XXX, k49, k4a, k4b, k4c, k4d} \ | |||
} | |||
#endif |
@ -0,0 +1,67 @@ | |||
# MCU name | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# change yes to no to disable | |||
# | |||
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = no # Console for debug(+400) | |||
COMMAND_ENABLE = no # Commands for debug and configuration | |||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |||
NKRO_ENABLE = no # USB Nkey Rollover | |||
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default | |||
MIDI_ENABLE = no # MIDI controls | |||
UNICODE_ENABLE = no # Unicode | |||
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | |||
AUDIO_ENABLE = no # Audio output on port C6 |