* Update Layer functions to use layer_state_t in ZSA Boards
* Update Music Mask for ZSA boards
Fixes an issue with the board getting stuck on Adjust layer when activating music mode
* Add Support for SMART LED Toggle to Planck EZ
* Add support for SMART LED toggle in Ergodox EZ
* Ifdef swiss cheeze for Oryx Configurator
* Documentation and updates
* Add Oryx Keymap
* Add option to configure the layers for the Layer Indicator
* Update keymap with better examples
* Make sure eeprom is initialized before reading from it
* Force flush of LED matrix when suspending board
This fixes an issue where the LEDs don't fully clear sometimes when the host system goes to sleep
* Enable RGB Sleeping by default
* Add clarification about planck ez led layer config
* Optimize RGB Matrix rendering for Ergodox EZ
* Optimize RGB Matrix rendering for Planck EZ
* Update keyboards/planck/ez/config.h
Co-Authored-By: Joel Challis <git@zvecr.com>
* clean up rgb matrix extern usage
Moved rgb matrix boiler plate into macros
Rebased onto typing heatmap pr
* Fixing the reversed frame buffer access in digital rain
* Fixing digital rain & typing heatmap if keyreactive effects are not enabled
* Apply suggestions from code review
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Adding parenthesizes to DRIVER_LED_TOTAL where necessary
* Updated docs
* added notes about parentheses
* RGB Matrix overhaul
Breakout of animations to separate files
Integration of optimized int based math lib
Overhaul of rgb_matrix.c and animations for performance
* Updating effect function api for future extensions
* Combined the keypresses || keyreleases define checks into a single define so I stop forgetting it where necessary
* Moving define RGB_MATRIX_KEYREACTIVE_ENABLED earlier in the include chain
* Remove unnecessary IS_COMMAND definition in clueboard/66/rev4
* Replace keyboard_report->mods with get_mods() in IS_COMMAND definitions
* Update docs to use get_mods() instead of keyboard_report->mods
* Replace keyboard_report->mods with get_mods() in tmk_core/protocol/usb_hid/test
For some reason, this occurrence used KB_LSHIFT and KB_RSHIFT, which don't exist
* Replace keyboard_report->mods with get_mods() in Massdrop keyboards (as per @patrickmt)
The debounce filtering reports a key/switch change directly, without any extra delay. After that the debounce logic will filter all further changes, until the key/switch reports the same state for the given count of scans.
So a perfect switch will get a short debounce period and a bad key will get a much longer debounce period. The result is an adaptive debouncing period for each switch.
This value defines how often the same key/switch state has to be detected in successive reads until the next key state can be reported.
In other words this value defines the minimum debouncing period for a switch.
* Remove chording as it is not documented, not used, and needs work.
* Make Leader Key an optional feature.
* Switch from `PREVENT_STUCK_MODIFIERS` to `STRICT_LAYER_RELEASE`
* Remove `#define PREVENT_STUCK_MODIFIERS` from keymaps.
With these changes, the ergodox ez goes from 315 scans per second
when no keys are pressed (~3.17ms/scan) to 447 (~2.24ms/scan).
The changes to the pin read are just condensing the logic, and
replacing a lot of conditional operations with a single bitwise
inversion.
The change to row scanning is more significant, and merits
explanation. In general, you can only scan one row of a keyboard
at a time, because if you scan two rows, you no longer know
which row is pulling a given column down. But in the Ergodox
design, this isn't the case; the left hand is controlled by an
I2C-based GPIO expander, and the columns and rows are *completely
separate* electrically from the columns and rows on the right-hand
side.
So simply reading rows in parallel offers two significant
improvements. One is that we no longer need the 30us delay after
each right-hand row, because we're spending more than 30us
communicating with the left hand over i2c. Another is that we're
no longer wastefully sending i2c messages to the left hand
to unselect rows when no rows had actually been selected in the
first place. These delays were, between them, coming out to
nearly 30% of the time spent in each scan.
Signed-off-by: seebs <seebs@seebs.net>
* include variables and .h files as pp directives
* start layout compilation
* split ergodoxes up
* don't compile all layouts for everything
* might seg fault
* reset layouts variable
* actually reset layouts
* include rules.mk instead
* remove includes from rules.mk
* update variable setting
* load visualizer from path
* adds some more examples
* adds more layouts
* more boards added
* more boards added
* adds documentation for layouts
* use lowercase names for LAYOUT_
* add layout.json files for each layout
* add community folder, default keymaps for layouts
* touch-up default layouts
* touch-up layouts, some keyboard rules.mk
* update documentation for layouts
* fix up serial/i2c switches
Empirically, waiting for N consecutive identical scans as a debouncing
strategy doesn't work very well for the ErgoDox EZ where scans are very
slow compared to most keyboards. Instead, debounce the signals by
eagerly reporting a change as soon as one scan observes it, but then
ignoring further changes from that key for the next N scans.
This is implemented by keeping an extra matrix of uint8 countdowns, such
that only keys whose countdown is currently zero are eligible to change.
When we do observe a change, we bump that key's countdown to DEBOUNCE.
During each scan, every nonzero countdown is decremented.
With this approach to debouncing, much higher debounce constants are
tolerable, because latency does not increase with the constant, and
debounce countdowns on one key do not interfere with events on other
keys. The only negative effect of increasing the constant is that the
minimum duration of a keypress increases. Perhaps I'm just extremely
unlucky w.r.t. key switch quality, but I saw occasional bounces even
with DEBOUNCE=10; with 15, I've seen none so far. That's around 47ms,
which seems like an absolutely insane amount of time for a key to be
bouncy, but at least it works.
Some options I defined on the config.h file don't make much sense to other
keymaps so I revert the global config.h and add those options on the keymap
custom one.
This keymap was created to have a feel keys on a different place and to have as
fewer layers as possible.
Currently I have only 2 extra layers and only one of them is really required to
have all possible keys available.
Check out the README.md file for more information.
- Backlight on PB7 controlled by Timer1 Fast PWM (no interrupts).
- Backlight commands connected temporarily to top left keys.
- Backlight init called from matrix.c, since there's no generic keyboard_init() override function.
Drashna Jaelre
XScorpion2
Florian Didron
Konstantin Đorđević
Michael Graf
Joe Wasson
Jack Humbert
Erez Zukerman
Seebs
Erez Zukerman
Andrew Pritchard
Kyle Smith
Fred Sundvik
Thiago Alves
Evan Pitstick
Erez Zukerman
Ante Vukorepa
Wilba6582