* disambiguate Bootmagic rules in keymaps

The files edited by this commit were added at a point in time where `BOOTMAGIC_ENABLE = yes` enabled full Bootmagic.

This commit edits the files to specify that full Bootmagic is intended.

* remove BOOTMAGIC_ENABLE=full setting

* unify commented BOOTMAGIC_ENABLE rules in keyboards

Explicitly sets `BOOTMAGIC_ENABLE = no` in keyboards where the rule was commented out.

Command:

```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;#[ \t]*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-zA-Z]\+\).*;\1 = no       # Virtual DIP switch configuration;g' {} +
```

* remove commented Bootmagic rules from keymap/user level

Command:

```
find keyboards/ layouts/ users/ -type f -name 'rules.mk' -exec sed -i -e '/#.*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*/d' {} +
```

* update keyboard BOOTMAGIC_ENABLE rule formatting

Sets the formatting of BOOTMAGIC_ENABLE rules to `BOOTMAGIC_ENABLE = [value]`, without the inline comments (which will be replaced later).

Command:

```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
```

* update keyboards' BOOTMAGIC_ENABLE settings

Updates keyboard `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.

Command:

```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = \)full;\1lite;g' '{}' +
```

* update keymap/user BOOTMAGIC_ENABLE settings

Updates keymap/user `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.

Commands:

```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
```

* remove and replace inline comments in keyboards and keymap/user files

Removes and replaces the inline comments, which have been updated to read `Enable Bootmagic Lite`.

Commands:

```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = lite\);\1     # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = yes\);\1      # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = no\);\1       # Enable Bootmagic Lite;g' '{}' +
```

* rename improperly named makefiles

Some files intended to be used as makefiles had improper names causing them to not be used as intended when building.

This commit corrects the filenames of the affected files.

* update renamed file with new rule formatting

* update QMK's template files

Updates QMK's `rules.mk` templates to use the new inline comment.

* update QMK Docs

- remove documentation of full Bootmagic
- update links to Bootmagic Lite doc
- add doc for Magic Keycodes

* rules.mk patch for coarse/ixora and coarse/vinta

* Add Per Key functionality for AutoShift (#11536)

* LED Matrix: Reactive effect buffers & advanced indicators (#12588)

* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)

* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)

* LED Matrix: Split (#12633)

* [CI] Format code according to conventions (#12650)

* feat: infinite timeout for leader key (#6580)

* feat: implement leader_no_timeout logic

* docs(leader_key): infinite leader timeout docs

* Format code according to conventions (#12680)

* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)

* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)

Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1).  Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).

* Update ADC docs to match the actually used resolution

ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly.  Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).

* Fix pinToMux() for B12 and B13 on STM32F3xx

Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.

* Add support for all possible analog pins on STM32F1xx

Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families).  Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).

Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.

* Add support for all possible analog pins on STM32F4xx

Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled).  These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.

Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.

Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.

* Fix STM32F3xx ADC mux table in documentation

The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).

* Add STM32F1xx ADC pins to the documentation

* Add STM32F4xx ADC pins to the documentation

* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)

* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.

* Update flashing.md

* Update chconf.h

* Update config.h

* Update halconf.h

* Update mcuconf.h

* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)

* Add support for MCU = STM32F446 (#12619)

* Add support for MCU = STM32F446

* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h

* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64

* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.

* Format code according to conventions (#12682)

* Format code according to conventions (#12687)

* Add STM32L433 and L443 support (#12063)

* initial L433 commit

* change to XC

* fix L433

* disable all peripherals

* update system and peripheral clocks

* 433 change

* use its own board  files

* revert its own board files

* l433 specific change

* fix stm32l432xx define

* remove duplicate #define

* fix bootloader jump

* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h

* move to L443

* move to L443

* fix sdmmc in mcuconf.h

* include STM32L443

* add L443

* Include L443 in compatible microcontrollers

* Include L443 in compatible microcontrollers

* Update config bootloader jump description

* Update ChibiOS define reasoning

* Update quantum/mcu_selection.mk

* fix git conflict

* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)

* Fix bad PR merge for #6580. (#12721)

* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)

* [CI] Format code according to conventions (#12731)

* Fixing transport's led/rgb matrix suspend state logic (#12770)

* [CI] Format code according to conventions (#12772)

* Fix comment parsing (#12750)

* Added OLED fade out support (#12086)

* fix some references to bin/qmk that slipped in (#12832)

* Resolve a number of warnings in `qmk generate-api` (#12833)

* New command: qmk console (#12828)

* stash poc

* stash

* tidy up implementation

* Tidy up slightly for review

* Tidy up slightly for review

* Bodge environment to make tests pass

* Refactor away from asyncio due to windows issues

* Filter devices

* align vid/pid printing

* Add hidapi to the installers

* start preparing for multiple hid_listeners

* udev rules for hid_listen

* refactor to move closer to end state

* very basic implementation of the threaded model

* refactor how vid/pid/index are supplied and parsed

* windows improvements

* read the report directly when usage page isn't available

* add per-device colors, the choice to show names or numbers, and refactor

* add timestamps

* Add support for showing bootloaders

* tweak the color for bootloaders

* Align bootloader disconnect with connect color

* add support for showing all bootloaders

* fix the pyusb check

* tweaks

* fix exception

* hide a stack trace behind -v

* add --no-bootloaders option

* add documentation for qmk console

* Apply suggestions from code review

* pyformat

* clean up and flesh out KNOWN_BOOTLOADERS

* Remove pointless SERIAL_LINK_ENABLE rules (#12846)

* Make Swap Hands use PROGMEM (#12284)

This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.

* Fix another bin/qmk reference (#12856)

* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)

* Fixup build errors on `develop` branch. (#12723)

* LED Matrix: Effects! (#12651)

* Fix syntax error when compiling for ARM (#12866)

* Remove KEYMAP and LAYOUT_kc (#12160)

* alias KEYMAP to LAYOUT

* remove KEYMAP and LAYOUT_kc

* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)

* Rename `point_t` -> `led_point_t` (#12864)

* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)

* Add missing LED Matrix suspend code to suspend.c (#12878)

* LED Matrix: Documentation (#12685)

* Deprecate `send_unicode_hex_string()` (#12602)

* Fix spelling mistake regarding LED Matrix in split_common. (#12888)

* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)

* Use milc.subcommand.config instead of qmk.cli.config (#12915)

* Use milc.subcommand.config instead

* pyformat

* remove the config test

* Add function to allow repeated blinking of one layer (#12237)

* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time

* Update doc

* Rework rgblight blinking according to requested change

* optimize storage

* Fixup housekeeping from being invoked twice per loop. (#12933)

* matrix: wait for row signal to go HIGH for every row (#12945)

I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/

Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.

After this commit, all keyboard matrix rows are interpreted correctly.

I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.

* ensure we do not conflict with existing keymap aliases (#12976)

* Add support for up to 4 IS31FL3733 drivers (#12342)

* Convert Encoder callbacks to be boolean functions (#12805)

* [Keyboard] Fix Terrazzo build failure (#12977)

* Do not hard set config in CPTC files (#11864)

* [Keyboard] Corne - Remove legacy revision support (#12226)

* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)

* Add Full-duplex serial driver for ARM boards (#9842)

* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)

* Backlight: add defines for default level and breathing state (#12560)

* Add dire message about LUFA mass storage bootloader (#13014)

* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)

Was causing compiler errors on some systems.

* Fix keyboards/keymaps for boolean encoder callback changes (#12985)

* `backlight.c`: include `eeprom.h` (#13024)

* Add changelog for 2021-05-29 Breaking Changes merge (#12939)

* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version

* Add recent develop changes

* Sort recent develop changes

* Remove sections for ChibiOS changes per tzarc

No ChibiOS changes this round.

* Add and sort recent develop changes

* add notes about keyboard moves/deletions

* import changelog for PR 12172

Documents the change to BOOTMAGIC_ENABLE.

* update section headings

* re-sort changelog

* add additional note regarding Bootmagic changes

* remove changelog timestamp

* update dates in main Breaking Changes docs

* fix broken section anchors in previous changelogs

* add link to backlight/eeprom patch to changelog

* highlight some more changes

* link PRs from section headers

* Restore standard readme

* run: qmk cformat --core-only

* Refactor to use core backlight

* Remove custom implementation

* refactor keyboards using ST_STM32F072B_DISCOVERY to use 'MCU = STM32F072'

* refactor keyboards using GENERIC_STM32_F042X6 to use 'MCU = STM32F042'

* refactor keyboards using GENERIC_STM32_F103 to use 'MCU = STM32F103'

* Move boards to cannonkeys and share resources

* Share common files between cannonkey boards

* Fix ortho60 keymap

* update LED numbers

* Add RGB keys to Ortho60 and Ortho48

* Add Backlight control to default layout Ortho60 and 48

* Remove unnecessary ws2812.c SRC from rules.mk

* Update Practice60 to enable RGB via SPI DMA and use PWM backlight breathing

* Correct stm32f103c8t6 flash size in eeprom definition

* Remove unused files and improve ifdef checks

* Update quantum/rgblight.c

Co-Authored-By: awkannan <andrew.kannan@klaviyo.com>

* Update quantum/rgblight.c

Co-Authored-By: awkannan <andrew.kannan@klaviyo.com>

* EEPROM implementation fix and updated p60 code

* Update define

* Remove dead code

* Update keymap to remove test key

* Update keymap again

* Starting point for blue pill based practice60

* Changes

* add

* try raw bin no botloader

* swap back to bootloader version

* edit

* Remove debug LED flash

* Disable JTAG to open up B3 and B4

* Add led backlight support (no breathing yet)

* Update matrix for correctness

* RGB Underglow working in a very simple state

* not as bright

* Move to handwired

* revert ChibiOS_Test changes

* Changes based on PR comments

* Address PR comments v2

* Move files

* include variables and .h files as pp directives

* start layout compilation

* split ergodoxes up

* don't compile all layouts for everything

* might seg fault

* reset layouts variable

* actually reset layouts

* include rules.mk instead

* remove includes from rules.mk

* update variable setting

* load visualizer from path

* adds some more examples

* adds more layouts

* more boards added

* more boards added

* adds documentation for layouts

* use lowercase names for LAYOUT_

* add layout.json files for each layout

* add community folder, default keymaps for layouts

* touch-up default layouts

* touch-up layouts, some keyboard rules.mk

* update documentation for layouts

* fix up serial/i2c switches

* Modularity and gcc warnings fixes.

* Add ChibiOS support (USB stack + support files).

* Make usb_main more USB_DRIVER #define independent.

* Move chibios to tool.

* Implement jump-to-bootloader.

* Small updates.

* Fix bootloader-jump compiling.

* Move AVR specific sleep_led.c into avr.

* Add basic sleep_led for chibios.

* Update chibios README.

* NKRO fixes.

* Rename some Makefile defines.

* Move STM32 bootloader address config to separate .h file.

* Add ARM Teensies bootloader code.

* Fix chibios/usb_main GET_REPORT handing.

* Add missing #include to keymap.c.

* Make bootmagic.c code portable (_delay_ms -> wait_ms).

* Move declaration of keymap_config.

Should really not declare variables in .h files - since it's included
in different .c files, a proper linker then complains that the same
variable is declared more than once (once for each .c file that the
offending .h is included in).

* Add eeprom support for chibios/kinetis.

* Rename chibios example keyboard.

* Move chibios/cortex selection to local Makefiles.

* Chibios: use WFI in idle. WIP suspend stuff.

* ChibiOS/kinetis: sending remote wakeup.

* ChibiOS/STM32: send remote wakeup.

* Fix report size of boot protocol.

* Fix drop key stroke

Keyboard report should be checked if its transfer finishs successfully.
Otherwise key stroke can be missing when other key event occurs
before the last report transfer is done.

Boot protocol 10ms interval probably causes this problem in case
it receives key events in a row within the period. NKRO protocol
suffers less or nothing due to its interval 1ms.

* Chibios/usb_main: rename a variable for clarity.

* Add correct chibios/bootloader_jump for infinity KB.

* ChibiOS: make reset request more CMSISy.

* Chibios: Add breathing sleep LED on Kinetis MCUs.

* ChibiOS: Update infinity bootloader code to match updated ChibiOS.

* ChibiOS: prettify/document sleep_led code.

* Chibios: Remove the wait in the main loop.

* Add maple mini code.

* Do timeout when writing to CONSOLE EP queue.

Fixes TMK bug #266.

* Chibios: add 'core/protocol' to the makefiles' search path.

* Chibios: Update to new USB API.

* Chibios: add more guards for transmitting (fix a deadlock bug).

* Add update for chibios in README

* Chibios: Fix a HardFault bug (wait after start).

* Chibios: cleanup usb_main code.

* Chibios: Revert common.mk change (fix AVR linking problem).

* core: Fix chibios user compile options

Compile options can be defined in project Makefile such as UDEFS, UADEFS, UINCDIR, ULIBDIR and ULIBS.

* Sysv format for ChibiOS arm-none-eabi-size

Some new patches to ChibiOS puts heap as it's own section. So the
berkeley format is now useless, as the heap will be included in the
BSS report. The sysv format displays the bss size correctly.

* Fix hard-coded path of CHIBIOS

* Add support for new version of ChibiOS and Contrib

The Kinetis support has moved to a separate Contrib repository in
the newest version of Chibios. There has also been some structure
changes. So this adds support for those, while maintaining back-
wards compability.

* Update ChibiOS instructions

* Chibios: implement sleep LED for STM32.

* Chibios: Update the main chibios README.

* Chibios: fix STM32_BOOTLOADER_ADDRESS name.

* Chibios: make the default bootloader_jump redefinable (weak).

* Chibios: disable LTO (link-time optimisation).

With LTO enabled, sometimes things fail for mysterious reasons
(e.g. bootloader jump on WF with LEDs enabled), just because the
linker optimisation is too aggressive.

* Chibios: add default location for chibios-contrib.

* ChibiOS: update mk to match chibios/master.

* ChibiOS: update instructions.md.

* Add chibi_onekey example.

* Add comments to chibi_onekey Makefile.

* Rename some Makefile defines.

* Move STM32 bootloader address config to separate .h file.

* Rename chibios example keyboard.

* Move chibios/cortex selection to local Makefiles.

* Add Teensy LC onekey example.

* Chibios: use WFI in idle. WIP suspend stuff.

* Update chibi/teensy instructions.

* Update chibios/Teensy instructions.

* Add infinity_chibios

* Add keymap_hasu.c

* Infinity_chibios: select correct bootloader_jump.

* Infinity_chibios: improve comments.

* Add generic STM32F103C8T6 example.

* Add maple mini code.

* STM32F103x fixes.

* Add maple mini pinout pic.

* Chibios: updates for 3.0.4 git.

* Chibios: rename example stm32_onekey -> stm32_f072_onekey.

* Chibios: add makefiles for Teensy 3.x examples.

* Chibios: update Teensy 3.x instructions.

* Chibios: Tsy LC is cortex-m0plus.

* Chibios: add more guards for transmitting (fix a deadlock bug).

* Change README for chibios

* Chibios: update examples to current chibios git.

Match the changes in mainline chibios:
 - update chconf.h
 - update supplied ld scripts structure
 - update Teensy instructions (switch to official
    chibios and introduce contrib)

* Add ChibiOS and ChibiOS-Contrib submodules

Also fix the makefile path for them.

* Moves chibios keyboards to keyboards folder

* First version of ChibiOS compilation

Only the stm32_f072_onkey keyboard is ported at the moment. It
compiles, but still doesn't link.

* More chibios fixes

It now compiles without warnings and links

* Move the teensy_lc_onekey to the keyboards folder

* Clean up the make file rule structure

* Remove keymap_fn_to_action

* Update more ChibiOS keyboards to QMK

Most of them does not compile at the moment though.

* Use older version of Chibios libraries

The newest ones have problems with compilation

* Remove USB_UNCONFIGURED event

It isn't present in the older version of ChibiOS

* Fix the infinity_chibios compilation

* Fix potentially uninitialized variable

* Add missing include

* Fix the ChibiOS makefile

* Fix some Chibios keyboard compilation

* Revert the rules.mk file back to master version

* Combine the chibios and AVR makefiles

With just the required overrides in the respective platform
specific one.

* Slight makefile restrucuring

Platform specific compiler options

* Move avr specific targets out of the main rules

* Fix ChibiOS objcopy

The ChibiOS objcopy needs different parameters, so the parameters
are moved to the corresponding platform rule file

* Fix the objcopy for real this time

The comands were moved around, so chibios used avr and the ohter
way around.

Also change the objsize output format

* Fix the thumb flags

* Fix the infinity hasu keymap

* Per platform cpp flags

* Add gcc-arm-none-eabi package to travis

* Add arm-none-eabi-newlib to travis

* Fix the name of the libnewlib-arm-none-eabi lib

* Fix the ChibiOS paths

So that they are properly relative, and builds don't generate
extra folders

* Fix the board path of stm32_f103_onekey

* Only consider folders with Makefiles as subproject