coreboot-x230

pre-built coreboot images and documentation on how to flash them for the Thinkpad X230

These images:

• only support Intel(R) Core(TM) i5-3320M CPU @ 2.60GHz
• include Lenovo's proprietary VGA BIOS ROM. (if it might not be needed anymore, I'm happy for hints)
• include Intel's proprietary microcode update binary.
• include SeaBIOS as coreboot payload, for maximum compatibility.
• are meant to be flashed externally
• are compatible with Windows and Linux

Latest build

See our releases

Intel microcode version from 2018-01-08

• 20180108 (md5 871df55f0ab010ee384dabfc424f2c12)
• 06-3a-09 for Intel(R) Core(TM) i5-3320M CPU @ 2.60GHz

SeaBIOS version from 2017-11-10

• 1.11.0

When do we do a release?

Either when

• There is a new SeaBIOS release,
• There is a new Intel microcode release, or
• There is a coreboot issue that affects us (unlikely)

Flashing for the first time

EC firmware

Enter Lenovo's BIOS with F1 and check the embedded controller (EC) version to be 1.14 and upgrade using the latest bootable CD if it isn't. The EC cannot be upgraded when coreboot is installed. (In case a newer version should ever be available (I doubt it), you could temporarily flash back your original Lenovo BIOS image)

me_cleaner

The Intel Management Engine resides on the 8MB chip. We don't need to touch it for coreboot-upgrades in the future, but while opening up the Thinkpad anyways, we can save it and run ifdtool and me_cleaner on it:

  flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=128 -c "MX25L3206E/MX25L3208E" -r ifdmegbe.rom
  flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=128 -c "MX25L3206E/MX25L3208E" -r ifdmegbe2.rom
  diff ifdmegbe.rom ifdmegbe2.rom
  git clone https://github.com/corna/me_cleaner.git && cd me_cleaner
  ./me_cleaner.py -O ifdmegbe_meclean.rom ifdmegbe.rom
  ifdtool -u ifdmegbe_meclean.rom
  flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=128 -c "MX25L3206E/MX25L3208E" -w ifdmegbe_meclean.rom.new

save the 4MB chip

(internally, memory of the two chips is mapped together, the 8MB being the lower part, but we can essientially ignore that)

For the first time, we have to save the original image, just like we did with the 8MB chip above:

  flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=128 -r top1.rom
  flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=128 -r top2.rom
  diff top1.rom top2.rom

Flashing the coreboot / SeaBIOS image

When upgrading to a new version, for example when a new SeaBIOS version is available, only this has to be done.

Download the latest release image we provide here and flash it:

 flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=128 -w x230_coreboot_seabios_example_top.rom

How to flash

We flash externally, using a "Pomona 5250 8-pin SOIC test clip". You'll find one easily.

We connect it to a Raspberry Pi 3, running Raspbian and the following setup

• Serial connection using a "USB to Serial" Adapter and picocom or minicom

• in the SD Cards's /boot/config.txt file enable_uart=1 and dtparam=spi=on

• For flashrom we put spi_bcm2835 and spidev in /etc/modules

• Connect to a wifi or to network over ethernet.

• install flashrom

• connect the Clip to the Raspberry Pi 3:

       Edge of pi (furthest from you)
     L                                                CS
     E                                                |
     F +---------------------------------------------------------------------------------+
     T |  x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x  |
       |  x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x   x  |
     E +----------------------------------^---^---^---^-------------------------------^--+
     D                                    |   |   |   |                               |
     G                                   3.3V MOSIMISO|                              GND
     E                                 (VCC)         CLK
       Body of Pi (closest to you)
  

  and to your X230:

    Screen (furthest from you)
             __
      MOSI  5 --|  |-- 4  GND
       CLK  6 --|  |-- 3  N/C
       N/C  7 --|  |-- 2  MISO
       VCC  8 --|__|-- 1  CS
  
       Edge (closest to you)
  

Now you should be able to run the above mentioned flashrom commands.

How we build

Everything necessary to build coreboot is included in this project and building coreboot is not hard at all. Please refer to coreboot's own documentation.

When building, testing and doing a release here, we always try to upload our result to coreboot's board status project.