- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve#2222
- Buttons events source as button property instead of a global one
- Rename events source -> provider for all settings, consistent with the other things like relay and light providers
- AnalogPin to read between a certain analogRead() range
Trying to follow defaults here - analog 'press' is digital LOW, default value is HIGH, so no additional cfg entries are needed besides pin, level and changing evt source
- (debug) Refactor gpio command, add adc to show analogRead(pin)
- (debug) Add button command
Implemented based on:
https://gitter.im/tinkerman-cat/espurna?at=5f5d44c8df4af236f902e25dhttps://gitter.im/tinkerman-cat/espurna?at=5f60e7f1f969413294e95370
- (experimental) provide generic way to read magnitude values
- expose /api/metrics with values formatted specifically for prometheus, with relay and sensor data
- small tweaks to sensor init
Example config:
```
scrape_configs:
- job_name: 'espurna'
metrics_path: '/api/metrics'
params:
apikey: ['apikeyapikey']
static_configs:
- targets: ['espurna-blabla.lan:80']
```
Where ESPurna side has
```
apiKey => "apikeyapikey"
apiEnabled => "1"
```
Add support for BME680 using libalgobsec proprietary algorithms for precise Indoor Air Quality (IAQ) measurement. Unlike traditional CO2 sensors - and good ones are expensive - it measures nearly all VOCs compounds in the air (plus other gases) and compensates those measurements with its built-in temperature and humidity sensors to determine indoor air quality.
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
Add new V3.0 version of PZEM004T, not tested. Default to factory default address 0xf8, configurable through pzemv30Addr 8-bit number
Add 'frequency' measurement & 'hz' unit
Add pz.address that configures address
Implemented energy reset
Right now we only support a single device. No way to test this properly (mostly, how exactly we need to connect this stuff), so left as not implemented.
Change the underlying command line handling:
- switch to a custom parser, inspired by redis / sds
- update terminalRegisterCommand signature, pass only bare minimum
- clean-up `help` & `commands`. update settings `set`, `get` and `del`
- allow our custom test suite to run command-line tests
- clean-up Stream IO to allow us to print large things into debug stream (for example, `eeprom.dump`)
- send parsing errors to the debug log
As a proof of concept, introduce `TERMINAL_MQTT_SUPPORT` and `TERMINAL_WEB_API_SUPPORT`
- MQTT subscribes to the `<root>/cmd/set` and sends response to the `<root>/cmd`. We can't output too much, as we don't have any large-send API.
- Web API listens to the `/api/cmd?apikey=...&line=...` (or PUT, params inside the body). This one is intended as a possible replacement of the `API_SUPPORT`. Internals introduce a 'task' around the AsyncWebServerRequest object that will simulate what WiFiClient does and push data into it continuously, switching between CONT and SYS.
Both are experimental. We only accept a single command and not every command is updated to use Print `ctx.output` object. We are also somewhat limited by the Print / Stream overall, perhaps I am overestimating the usefulness of Arduino compatibility to such an extent :)
Web API handler can also sometimes show only part of the result, whenever the command tries to yield() by itself waiting for something. Perhaps we would need to create a custom request handler for that specific use-case.
This will add support for the KingArt Wifi Curtain Switch. There are no buttons in the web interface as I could not figure out how to create them (any help on that is welcome).
For now the switch can be controlled over MQTT:
"{hostname}/curtain/set"
"{hostname}/curtain"
* ADC_VCC is not macro
* In esp.h ADC_VCC and ADC_TOUT is not macro, so define macro.
* ADC_VCC and ADC_TOUT fixes in utils.ino and sensors.h
* Adding support for I2C temperature and humidity sensor HDC1080 / 831R
* Added HDC1080 to test\build\sensor.h and arduino.h
* added brackets
* Revert ADC_MODE_VALUE to initial values
* Eof newline
* Eof newline
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
* Sensors: refactor configuration
- move sensor implementaion to the .ino,
remove dependency undef / define from sensor files
- update test/build/sensor.h from SENSOR_SUPPORT
- allow to change sensor config variables externally
- `#include <...>` for global headers and libraries,
fix relative path for math library
* add missing sns <-> i2c dependency
* ledrelay should return relay_none as default
* rollback to original test header
* include debug header when requested (relative)
- add experimental `relayDummy` to configure dummy relays at runtime
- add tuya-generic-dimmer #1729
- cleanup broker interface to allow Tuya module to properly receive events, modify broker methods to allow different function signatures
- add basic tests for Tuya frame and data protocol
* Use generic typechecks, OTA add followRedirects
* revamp using is_detected
* relative include
* mention ts draft instead, fix c++17 includes (still not buildable)
* typo
* Always create WiFiClient pointer
* Remove old CREATE_CHECK macro
* do not create wificlient obj when running old Core
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Updated copyright string
* Buffer from 6 bytes to 8 bytes
Current gcc-4 does not mark this as warning, but gcc-9 notices the 3 char size requirement. Buffer should be 8
* Use 5000ppm max
* travis: move build flags tests outside of hardware header
* mqtt: fix typo
* travis: use files instead of bundling test cases into script
* fixup! travis: use files instead of bundling test cases into script
* fix variable expansion, remove custom h at the end
* add ade7953 to sensors list
* custom.h path as variable
* shellcheck
* fix printf syntax, silent again
* fix bash 4.3 treating empty array as unset variable
Maxim Prokhorov
DmitryBlinov
Rui Marinho
Albert Weterings
Alexander
Niek van der Maas
James