- gpio module now tracks the known providers (right now, hardware and mcp expander)
- refactored relay struct to use 'Provider' implementing setup,notify,change,boot instead of just BasePin actions
- refactored button module to use gpio provider instead of referencing types itself
- removed dual & stm code from buttons, migrate both to relay module
- added status notify and change callbacks for relayStatus (i.e. 'notify' when relay status was called, but not changed. and 'changed' when it did)
- relays runtime configuration keys
- relay command now shows configured relays and current & target statuses
- refactor the code using relayStatus(0, blah) under LIGHT_PROVIDER check to use lightState instead
- remove rfbridge code form relay module. implement through a basic state listener in the rfbridge module, depend on RELAY_SUPPORT
- allow to bind rf codes to real relays
- drop tuya-specific lights provider, remove tuya code from relays and lights modules
- integrate tuya via relay listeners and providers, use lights custom provider
- implement channel transitions for tuya. disabled by default, and transition time and step are overridden to 2000 + 100. needs to be set to some value below the total time (i.e. `total transition time / step time == number of steps`, we need to figure out a correct time that serial comms could handle)
- lights custom provider (global, not per-pin) and state listeners
- remove lights code from relay module. implement through providers & listeners in the lights module, depend on RELAY_SUPPORT
- lights per-channel relay provider (unused atm), depend on RELAY_SUPPORT
- refactored channel transition - calculate step only once, make sure time + step values are sane, generate quick transitions with very small delay (10ms hardcoded) for transitions during OFF state i.e. we no longer waste 500ms (or whatever transition time is set to) on boot doing nothing
- transition time + step parameter for the lightUpdate
- report mask parameter for the lightUpdate
- minor fixes across the board
resolve#2222
fixes#2407
avoid depending on other settings
technically, it could be another block in the snsConfigure for
magnitudes, however it also should be a new type of one-shot logic
- match paths through a custom AsyncWebHandler instead of using generic not-found fallback handler
- allow MQTT-like patterns when registering paths (`simple/path`, `path/+/something`, `path/#`)
Replaces `relay/0`, `relay/1` etc. with `relay/+`. Magnitudes are plain paths, but using `/+` in case there's more than 1 magnitude of the same type.
- restore `std::function` as callback container (no more single-byte arg nonsense). Still, limit to 1 type per handler type
- adds JSON handlers which will receive JsonObject root as both input and output. Same logic as plain - GET returns resource data, PUT updates it.
- breaking change to `apiAuthenticate(request)`, it no longer will do `request->send(403)` and expect this to be handled externally.
- allow `Api-Key` header containing the key, works for both GET & PUT plain requests. The only way to set apikey for JSON.
- add `ApiRequest::param` to retrieve both GET and PUT params (aka args), remove ApiBuffer
- remove `API_BUFFER_SIZE`. Allow custom form-data key=value pairs for requests, allow to send basic `String`.
- add `API_JSON_BUFFER_SIZE` for the JSON buffer (both input and output)
- `/apis` replaced with `/api/list`, no longer uses custom handler and is an `apiRegister` callback
- `/api/rpc` custom handler replaced with an `apiRegister` callback
WIP further down:
- no more `webLog` for API requests, unless `webAccessLog` / `WEB_ACCESS_LOG` is set to `1`. This also needs to happen to the other handlers.
- migrate to ArduinoJson v6, since it become apparent it is actually a good upgrade :)
- actually make use of JSON endpoints more, right now it's just existing GET for sensors and relays
- fork ESPAsyncWebServer to cleanup path parsing and temporary objects attached to the request (also, fix things a lot of things based on PRs there...)
Always do digitalRead() after ISR
Drop trigger, since we can handle this inside of reading routine
(although, pending some changes to make reading interval per-sensor)
Rework read / write through std::atomic
vector will not copy when move ctor is marked noexcept
remove the copy ctor 'trick', re-add dtor. explicitly do the thing we want
(...clang-tidy would've shown this issue, something to do in the CI...)
- magnitudes vector grows by calling copy ctor, ensure filter never gets deleted
- ensure we can't use magnitude member instead of ctor arg
- more magnitude references instead of using index access
- additional checks for isnan, fix report never triggering
- drop event callback. at least for EventSensor, we already have
report with min / max value change triggers
- BaseFilter must have virtual dtor
- magnitude object is not trivial, we need to manage filter lifetime
- Ensure move also moves filter object
- Clean-up using magnitude object by value in functions
- (experimental) provide generic way to read magnitude values
- expose /api/metrics with values formatted specifically for prometheus, with relay and sensor data
- small tweaks to sensor init
Example config:
```
scrape_configs:
- job_name: 'espurna'
metrics_path: '/api/metrics'
params:
apikey: ['apikeyapikey']
static_configs:
- targets: ['espurna-blabla.lan:80']
```
Where ESPurna side has
```
apiKey => "apikeyapikey"
apiEnabled => "1"
```
- reduce overall size of the structure, store a single required entity
inside of Api object itself.
- tweak internal functions to expect a certain path size
- (kind of a hack) add manual calls to vector<Api>::reserve() as we go over
the current capacity and vector increases it's size times 2.
e.g. for 9 relays, we would allocate space for 32 Api objects
when vector size goes from 16 to 32, after we add 18 Api objects with relay + pulse
- (breaking) json calls on a separate path, don't waste time encoding
a single entity as json object when we can encode more things
Add support for BME680 using libalgobsec proprietary algorithms for precise Indoor Air Quality (IAQ) measurement. Unlike traditional CO2 sensors - and good ones are expensive - it measures nearly all VOCs compounds in the air (plus other gases) and compensates those measurements with its built-in temperature and humidity sensors to determine indoor air quality.
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
Add new V3.0 version of PZEM004T, not tested. Default to factory default address 0xf8, configurable through pzemv30Addr 8-bit number
Add 'frequency' measurement & 'hz' unit
Add pz.address that configures address
Implemented energy reset
Right now we only support a single device. No way to test this properly (mostly, how exactly we need to connect this stuff), so left as not implemented.
- introduce zero threshold setting to reset value to 0 below a certain point (resolve#2264)
for example, set pwrPZeroThreshold0 10.0 for active power (or pwrQ... for apparent, pwrModS... for reactive) will reset always reset value to 0, similar to what turned off relay does. Default value is nan, since we can't use 0.0 on account of negative values.
- fix energy magnitude indexes usage, properly reset in API
- simplify sending pwr and emon Visible flags
- allow to use settings prefixes more, remove snsMinDelta & snsMaxDelta and use relative magnitude indexes
Change the underlying command line handling:
- switch to a custom parser, inspired by redis / sds
- update terminalRegisterCommand signature, pass only bare minimum
- clean-up `help` & `commands`. update settings `set`, `get` and `del`
- allow our custom test suite to run command-line tests
- clean-up Stream IO to allow us to print large things into debug stream (for example, `eeprom.dump`)
- send parsing errors to the debug log
As a proof of concept, introduce `TERMINAL_MQTT_SUPPORT` and `TERMINAL_WEB_API_SUPPORT`
- MQTT subscribes to the `<root>/cmd/set` and sends response to the `<root>/cmd`. We can't output too much, as we don't have any large-send API.
- Web API listens to the `/api/cmd?apikey=...&line=...` (or PUT, params inside the body). This one is intended as a possible replacement of the `API_SUPPORT`. Internals introduce a 'task' around the AsyncWebServerRequest object that will simulate what WiFiClient does and push data into it continuously, switching between CONT and SYS.
Both are experimental. We only accept a single command and not every command is updated to use Print `ctx.output` object. We are also somewhat limited by the Print / Stream overall, perhaps I am overestimating the usefulness of Arduino compatibility to such an extent :)
Web API handler can also sometimes show only part of the result, whenever the command tries to yield() by itself waiting for something. Perhaps we would need to create a custom request handler for that specific use-case.
* broker: declare and define per module
We no longer need to specify each Broker type in broker.h
But, we exchange that bit for explicit initialization of the instance
Define helper macros to generate boilerplate code
- namespace with Instance, Register(), Publish()
- forward Register(...) -> Instance.Register(...),
Publish(...) -> Instance.Publish(...)
* don't check for broker when deps enable it
* emon: configure ratios without reboot
* settings: serialize() support
* debug: use vsnprintf from newlib, not from sdk
* settings/experimental: show defaults via `get`
* emon: override base methods, fix defaults
* sensor/emon: expose internal index calculation
- refactor configuration to use the correct index when accessing indexed
sensor methods. store index value on magnitude, refactor loops to
accomodate this new functionality
- rename slot(index) -> description(index), since we use 'slot' as
numeric value
- general conversion from .ino modules into a separate .cpp files
- clean-up internal headers, place libraries into .h. guard .cpp with _SUPPORT flags
- fix some instances of shared variables instead of public methods
- tweak build system to still build a single source file via os environment variable ESPURNA_BUILD_SINGLE_SOURCE
* hlw8012: load hardware-specific ratios
* hlw8012: read energy in pre() callback
* dcz: nvalue should be integer
* sns: fix pressure constrain
* sns: load ratios based on index too
* sns: per-magnitude corrections (still limited by type)
* sns: attach units to index
* ADC_VCC is not macro
* In esp.h ADC_VCC and ADC_TOUT is not macro, so define macro.
* ADC_VCC and ADC_TOUT fixes in utils.ino and sensors.h
* Adding support for I2C temperature and humidity sensor HDC1080 / 831R
* Added HDC1080 to test\build\sensor.h and arduino.h
* added brackets
* Revert ADC_MODE_VALUE to initial values
* Eof newline
* Eof newline
Co-authored-by: Max Prokhorov <prokhorov.max@outlook.com>
- Domoticz only accepts svalue <pressure>;<forecast>,
failing to display anything otherwise.
We don't have any forecast calculation (yet?), simply send dummy value.
- Move Domoticz code outside of sensor.ino
- Update sensor classes to support a generic way to store energy values
- Update sensor conversion code to deal with units and not magnitudes
- Add magnitude<->unit for sensors, generic way of defining used unit. Convert from sensor magnitude unit to the one used for display.
- Reset energy value based on index through external means (MQTT, HTTP)
- Rework energy timestamping, update webui with 'last saved' value
While this solves the energy conversion issues and we are finally seeing the real value, what I don't really like:
- KilowattHour and WattHour are separate enum tags, thus sort-of are different types altogether
- Conversion code in Energy object should probably use some generic 'ratio' calculation? (https://en.cppreference.com/w/cpp/numeric/ratio/ratio)
- We are still using runtime checks to do calculations and depend that sensor outputs only one specific value type.
Consider this a fix for energy display / storage and preliminary work on sensor.ino
Further sensor refactoring... soon.
* Sensors: refactor configuration
- move sensor implementaion to the .ino,
remove dependency undef / define from sensor files
- update test/build/sensor.h from SENSOR_SUPPORT
- allow to change sensor config variables externally
- `#include <...>` for global headers and libraries,
fix relative path for math library
* add missing sns <-> i2c dependency
* ledrelay should return relay_none as default
* rollback to original test header
* include debug header when requested (relative)
* scripts: memanalyzer fixes
- cleanup duplication
- cleanup external dependencies
- properly use subprocess when calling pio, add debug mode
- cleanup argparse usage, use store_true actions instead of counters
- use python3 syntax and python3 shebang by default
- fix some issues with module dependencies
* move to scripts
* use simple return
* quick fix for rfm
* codacy unused import
* formatting
* show defaults
* while at it, rewrite to make pylint happy
* fix unused
* add windows support + note
- mask is defined as (relay# status << number)
- transparently handle base-2 and base-10 numbers
- if the relay mode requires us to save the mask, it will be saved as base-2
- add experimental `relayDummy` to configure dummy relays at runtime
- add tuya-generic-dimmer #1729
- cleanup broker interface to allow Tuya module to properly receive events, modify broker methods to allow different function signatures
- add basic tests for Tuya frame and data protocol
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Added T6613
* Updated copyright string
* Buffer from 6 bytes to 8 bytes
Current gcc-4 does not mark this as warning, but gcc-9 notices the 3 char size requirement. Buffer should be 8
* Use 5000ppm max
* Use indexed keys for energy saving
* match else even when rtcmem cannot fit the value
* fix energy reset placement
* fix rtcmem->energy size check
* revert to pre 62a2b9e value, handle update from 1.13.5
* Add Shelly 2.5
* Add ADE7953 sensor support
* Fix compilation
* Use only one instance
* WIP: Not working, I got StoreProhibited exception
* Fix exception
* Fix merge issues
* Apply request review changes
* declare struct before using it
* uninterruptible delay
* try optimized reg_size
* fix types
* Remove gpio 0 input in analog sensor
* Add energy to ADE7953, it is not finished yet
* Add new method to save energy with index
* Finish energy for ADE7953
Max Prokhorov
Rui Marinho
Alexander
irmishappy
James
Antonio López Marín