mhsw-espurna/code/espurna/config/hardware.h

// -----------------------------------------------------------------------------
// Configuration HELP
// -----------------------------------------------------------------------------
//
// MANUFACTURER: Name of the manufacturer of the board ("string")
// DEVICE: Name of the device ("string")
// BUTTON#_PIN: GPIO for the n-th button (1-based, up to 4 buttons)
// BUTTON#_RELAY: Relay number that will be bind to the n-th button (1-based)
// BUTTON#_MODE: A mask of options (BUTTON_PUSHBUTTON and BUTTON_SWITCH cannot be together)
//   - BUTTON_PUSHBUTTON: button event is fired when released
//   - BUTTON_SWITCH: button event is fired when pressed or released
//   - BUTTON_DEFAULT_HIGH: there is a pull up in place
//   - BUTTON_SET_PULLUP: set pullup by software
// RELAY#_PIN: GPIO for the n-th relay (1-based, up to 4 relays)
// RELAY#_TYPE: Relay can be RELAY_TYPE_NORMAL, RELAY_TYPE_INVERSE or RELAY_TYPE_LATCHED
// LED#_PIN: GPIO for the n-th LED (1-based, up to 4 LEDs)
// LED#_PIN_INVERSE: LED has inversed logic (lit when pulled down)
// LED#_MODE: Check hardware.h for LED_MODE_%
// LED#_RELAY: Linked relay (1-based)
//
// Besides, other hardware specific information should be stated here

// -----------------------------------------------------------------------------
// Development boards
// -----------------------------------------------------------------------------

#if defined(NODEMCU_LOLIN)

    // Info
    #define MANUFACTURER        "NODEMCU"
    #define DEVICE              "LOLIN"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            2
    #define LED1_PIN_INVERSE    1

#elif defined(WEMOS_D1_MINI_RELAYSHIELD)

    // Info
    #define MANUFACTURER        "WEMOS"
    #define DEVICE              "D1_MINI_RELAYSHIELD"

    // Buttons
    // No buttons on the D1 MINI alone, but defining it without adding a button doen't create problems
    #define BUTTON1_PIN         0   // Connect a pushbutton between D3 and GND,
                                    // it's the same as using a Wemos one button shield
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          5
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            2
    #define LED1_PIN_INVERSE    1

    // When Wemos relay shield is connected GPIO5 (D1) is used for relay,
    // so I2C must be remapped to other pins
    #define I2C_SDA_PIN         12  // D6
    #define I2C_SCL_PIN         14  // D5

#elif defined(WEMOS_D1_TARPUNA_SHIELD)

    // Info
    #define MANUFACTURER        "WEMOS"
    #define DEVICE              "D1_TARPUNA_SHIELD"

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

// -----------------------------------------------------------------------------
// ESPurna
// -----------------------------------------------------------------------------

#elif defined(TINKERMAN_ESPURNA_H06)

    // Info
    #define MANUFACTURER        "TINKERMAN"
    #define DEVICE              "ESPURNA_H06"

    // Buttons
    #define BUTTON1_PIN         4
    #define BUTTON1_RELAY       1

    // Normal pushbutton
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_INVERSE

    // LEDs
    #define LED1_PIN            2
    #define LED1_PIN_INVERSE    1

    // HLW8012
    #ifndef HLW8012_SUPPORT
    #define HLW8012_SUPPORT     1
    #endif
    #define HLW8012_SEL_PIN     2
    #define HLW8012_CF1_PIN     13
    #define HLW8012_CF_PIN      14

#elif defined(TINKERMAN_ESPURNA_H08)

    // Info
    #define MANUFACTURER        "TINKERMAN"
    #define DEVICE              "ESPURNA_H08"

    // Buttons
    #define BUTTON1_PIN         4
    #define BUTTON1_RELAY       1

    // Normal pushbutton
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            2
    #define LED1_PIN_INVERSE    0

    // HLW8012
    #ifndef HLW8012_SUPPORT
    #define HLW8012_SUPPORT     1
    #endif
    #define HLW8012_SEL_PIN     5
    #define HLW8012_CF1_PIN     13
    #define HLW8012_CF_PIN      14

#elif defined(TINKERMAN_ESPURNA_SWITCH)

    // Info
    #define MANUFACTURER        "TINKERMAN"
    #define DEVICE              "ESPURNA_SWITCH"

    // Buttons
    #define BUTTON1_PIN         4
    #define BUTTON1_RELAY       1

    // Touch button
    #define BUTTON1_MODE            BUTTON_PUSHBUTTON
    #define BUTTON1_PRESS           BUTTON_MODE_TOGGLE
    #define BUTTON1_CLICK           BUTTON_MODE_NONE
    #define BUTTON1_DBLCLICK        BUTTON_MODE_NONE
    #define BUTTON1_LNGCLICK        BUTTON_MODE_NONE
    #define BUTTON1_LNGLNGCLICK     BUTTON_MODE_NONE

    // LEDs
    #define LED1_PIN            2
    #define LED1_PIN_INVERSE    0

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_INVERSE

// -----------------------------------------------------------------------------
// Itead Studio boards
// -----------------------------------------------------------------------------

#elif defined(ITEAD_SONOFF_BASIC)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_BASIC"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1
    #define BUTTON2_PIN         14
    #define BUTTON2_MODE        BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
    #define BUTTON2_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_SONOFF_RF)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_RF"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1
    #define BUTTON2_PIN         14
    #define BUTTON2_MODE        BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
    #define BUTTON2_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_SONOFF_TH)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_TH"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

    // Jack is connected to GPIO14 (and with a small hack to GPIO4)
    #ifndef DALLAS_SUPPORT
    #define DALLAS_SUPPORT      1
    #endif
    #define DALLAS_PIN          14

    #ifndef DHT_SUPPORT
    #define DHT_SUPPORT         1
    #endif
    #define DHT_PIN             14

    //#define I2C_SDA_PIN         4
    //#define I2C_SCL_PIN         14

#elif defined(ITEAD_SONOFF_SV)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_SV"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_SLAMPHER)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SLAMPHER"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_S20)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "S20"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_SONOFF_TOUCH)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_TOUCH"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_PRESS       BUTTON_MODE_TOGGLE
    #define BUTTON1_CLICK       BUTTON_MODE_NONE
    #define BUTTON1_DBLCLICK    BUTTON_MODE_NONE
    #define BUTTON1_LNGCLICK    BUTTON_MODE_NONE
    #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_SONOFF_POW)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_POW"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            15
    #define LED1_PIN_INVERSE    0

    // HLW8012
    #ifndef HLW8012_SUPPORT
    #define HLW8012_SUPPORT     1
    #endif
    #define HLW8012_SEL_PIN     5
    #define HLW8012_CF1_PIN     13
    #define HLW8012_CF_PIN      14

#elif defined(ITEAD_SONOFF_DUAL)

    // Info
    #define MANUFACTURER            "ITEAD"
    #define DEVICE                  "SONOFF_DUAL"
    #define SERIAL_BAUDRATE         19230
    #define RELAY_PROVIDER          RELAY_PROVIDER_DUAL
    #define DUMMY_RELAY_COUNT       2
    #define DEBUG_SERIAL_SUPPORT    0
    #define TERMINAL_SUPPORT        0

    // Buttons
    #define BUTTON3_RELAY       1

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_SONOFF_DUAL_R2)

    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_DUAL_R2"

    // Buttons
    #define BUTTON1_PIN         0       // Button 0 on header
    #define BUTTON2_PIN         9       // Button 1 on header
    #define BUTTON3_PIN         10      // Physical button
    #define BUTTON1_RELAY       1
    #define BUTTON2_RELAY       2
    #define BUTTON3_RELAY       1
    #define BUTTON1_MODE        BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
    #define BUTTON2_MODE        BUTTON_SWITCH | BUTTON_SET_PULLUP | BUTTON_DEFAULT_HIGH
    #define BUTTON3_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    // Relays
    #define RELAY1_PIN          12
    #define RELAY2_PIN          5
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL
    #define RELAY2_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_SONOFF_4CH)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_4CH"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON2_PIN         9
    #define BUTTON3_PIN         10
    #define BUTTON4_PIN         14

    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON2_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON3_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON4_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    #define BUTTON1_RELAY       1
    #define BUTTON2_RELAY       2
    #define BUTTON3_RELAY       3
    #define BUTTON4_RELAY       4

    // Relays
    #define RELAY1_PIN          12
    #define RELAY2_PIN          5
    #define RELAY3_PIN          4
    #define RELAY4_PIN          15

    #define RELAY1_TYPE         RELAY_TYPE_NORMAL
    #define RELAY2_TYPE         RELAY_TYPE_NORMAL
    #define RELAY3_TYPE         RELAY_TYPE_NORMAL
    #define RELAY4_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_SONOFF_4CH_PRO)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_4CH_PRO"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON2_PIN         9
    #define BUTTON3_PIN         10
    #define BUTTON4_PIN         14

    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON2_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON3_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON4_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    #define BUTTON1_RELAY       1
    #define BUTTON2_RELAY       2
    #define BUTTON3_RELAY       3
    #define BUTTON4_RELAY       4

    // Sonoff 4CH Pro uses a secondary STM32 microcontroller to handle
    // buttons and relays, but it also forwards button presses to the ESP8285.
    // This allows ESPurna to handle button presses -almost- the same way
    // as with other devices except:
    // * Double click seems to break/disable the button on the STM32 side
    // * With S6 switch to 1 (self-locking and inching modes) everything's OK
    // * With S6 switch to 0 (interlock mode) if there is a relay ON
    //    and you click on another relay button, the STM32 sends a "press"
    //    event for the button of the first relay (to turn it OFF) but it
    //    does not send a "release" event. It's like it's holding the
    //    button down since you can see it is still LOW.
    //    Whatever reason the result is that it may actually perform a
    //    long click or long-long click.
    // The configuration below make the button toggle the relay on press events
    // and disables any possibly harmful combination with S6 set to 0.
    // If you are sure you will only use S6 to 1 you can comment the
    // BUTTON1_LNGCLICK and BUTTON1_LNGLNGCLICK options below to recover the
    // AP mode and factory reset functionalities.

    #define BUTTON1_PRESS       BUTTON_MODE_TOGGLE
    #define BUTTON1_CLICK       BUTTON_MODE_NONE
    #define BUTTON1_DBLCLICK    BUTTON_MODE_NONE
    #define BUTTON1_LNGCLICK    BUTTON_MODE_NONE
    #define BUTTON1_LNGLNGCLICK BUTTON_MODE_NONE
    #define BUTTON2_PRESS       BUTTON_MODE_TOGGLE
    #define BUTTON2_CLICK       BUTTON_MODE_NONE
    #define BUTTON3_PRESS       BUTTON_MODE_TOGGLE
    #define BUTTON3_CLICK       BUTTON_MODE_NONE
    #define BUTTON4_PRESS       BUTTON_MODE_TOGGLE
    #define BUTTON4_CLICK       BUTTON_MODE_NONE

    // Relays
    #define RELAY1_PIN          12
    #define RELAY2_PIN          5
    #define RELAY3_PIN          4
    #define RELAY4_PIN          15

    #define RELAY1_TYPE         RELAY_TYPE_NORMAL
    #define RELAY2_TYPE         RELAY_TYPE_NORMAL
    #define RELAY3_TYPE         RELAY_TYPE_NORMAL
    #define RELAY4_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_1CH_INCHING)

    // The inching functionality is managed by a misterious IC in the board.
    // You cannot control the inching button and functionality from the ESP8266
    // Besides, enabling the inching functionality using the hardware button
    // will result in the relay switching on and off continuously.
    // Fortunately the unkown IC keeps memory of the hardware inching status
    // so you can just disable it and forget. The inching LED must be lit.
    // You can still use the pulse options from the web interface
    // without problem.

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "1CH_INCHING"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_MOTOR)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "MOTOR"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_RELAY       1
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_BNSZ01)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "BNSZ01"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

    // Light
    #define LIGHT_CHANNELS      1
    #define LIGHT_CH1_PIN       12
    #define LIGHT_CH1_INVERSE   0

#elif defined(ITEAD_SONOFF_RFBRIDGE)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_RFBRIDGE"
    #define SERIAL_BAUDRATE     19200
    #define RELAY_PROVIDER      RELAY_PROVIDER_RFBRIDGE

    #ifndef DUMMY_RELAY_COUNT
    #define DUMMY_RELAY_COUNT   8
    #endif

    // Remove UART noise on serial line
    #define TERMINAL_SUPPORT        0
    #define DEBUG_SERIAL_SUPPORT    0

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_SONOFF_B1)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_B1"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_MY92XX
    #define DUMMY_RELAY_COUNT   1

    // Light
    #define LIGHT_CHANNELS      5
    #define MY92XX_MODEL        MY92XX_MODEL_MY9231
    #define MY92XX_CHIPS        2
    #define MY92XX_DI_PIN       12
    #define MY92XX_DCKI_PIN     14
    #define MY92XX_COMMAND      MY92XX_COMMAND_DEFAULT
    #define MY92XX_MAPPING      4, 3, 5, 0, 1

#elif defined(ITEAD_SONOFF_LED)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_LED"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

    // Light
    #define LIGHT_CHANNELS      2
    #define LIGHT_CH1_PIN       12  // Cold white
    #define LIGHT_CH2_PIN       14  // Warm white
    #define LIGHT_CH1_INVERSE   0
    #define LIGHT_CH2_INVERSE   0

#elif defined(ITEAD_SONOFF_T1_1CH)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_T1_1CH"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_PRESS       BUTTON_MODE_TOGGLE
    #define BUTTON1_CLICK       BUTTON_MODE_NONE
    #define BUTTON1_DBLCLICK    BUTTON_MODE_NONE
    #define BUTTON1_LNGCLICK    BUTTON_MODE_NONE
    #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_SONOFF_T1_2CH)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_T1_2CH"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON2_PIN         9

    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_PRESS       BUTTON_MODE_TOGGLE
    #define BUTTON1_CLICK       BUTTON_MODE_NONE
    #define BUTTON1_DBLCLICK    BUTTON_MODE_NONE
    #define BUTTON1_LNGCLICK    BUTTON_MODE_NONE
    #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET

    #define BUTTON2_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON2_PRESS       BUTTON_MODE_TOGGLE
    #define BUTTON2_CLICK       BUTTON_MODE_NONE
    #define BUTTON2_DBLCLICK    BUTTON_MODE_NONE
    #define BUTTON2_LNGCLICK    BUTTON_MODE_NONE
    #define BUTTON2_LNGLNGCLICK BUTTON_MODE_RESET

    #define BUTTON1_RELAY       1
    #define BUTTON2_RELAY       2

    // Relays
    #define RELAY1_PIN          12
    #define RELAY2_PIN          5

    #define RELAY1_TYPE         RELAY_TYPE_NORMAL
    #define RELAY2_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1

#elif defined(ITEAD_SONOFF_T1_3CH)

    // Info
    #define MANUFACTURER        "ITEAD"
    #define DEVICE              "SONOFF_T1_3CH"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON2_PIN         9
    #define BUTTON3_PIN         10

    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_PRESS       BUTTON_MODE_TOGGLE
    #define BUTTON1_CLICK       BUTTON_MODE_NONE
    #define BUTTON1_DBLCLICK    BUTTON_MODE_NONE
    #define BUTTON1_LNGCLICK    BUTTON_MODE_NONE
    #define BUTTON1_LNGLNGCLICK BUTTON_MODE_RESET

    #define BUTTON2_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON2_PRESS       BUTTON_MODE_TOGGLE
    #define BUTTON2_CLICK       BUTTON_MODE_NONE
    #define BUTTON2_DBLCLICK    BUTTON_MODE_NONE
    #define BUTTON2_LNGCLICK    BUTTON_MODE_NONE
    #define BUTTON2_LNGLNGCLICK BUTTON_MODE_RESET

    #define BUTTON3_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON3_PRESS       BUTTON_MODE_TOGGLE
    #define BUTTON3_CLICK       BUTTON_MODE_NONE
    #define BUTTON3_DBLCLICK    BUTTON_MODE_NONE
    #define BUTTON3_LNGCLICK    BUTTON_MODE_NONE
    #define BUTTON3_LNGLNGCLICK BUTTON_MODE_RESET

    #define BUTTON1_RELAY       1
    #define BUTTON2_RELAY       2
    #define BUTTON3_RELAY       3

    // Relays
    #define RELAY1_PIN          12
    #define RELAY2_PIN          5
    #define RELAY3_PIN          4

    #define RELAY1_TYPE         RELAY_TYPE_NORMAL
    #define RELAY2_TYPE         RELAY_TYPE_NORMAL
    #define RELAY3_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    1


// -----------------------------------------------------------------------------
// YJZK
// -----------------------------------------------------------------------------

#elif defined(YJZK_SWITCH_2CH)

    // Info
    #define MANUFACTURER        "YJZK"
    #define DEVICE              "SWITCH_2CH"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON2_PIN         9

    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON2_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    #define BUTTON1_RELAY       1
    #define BUTTON2_RELAY       2

    // Relays
    #define RELAY1_PIN          12
    #define RELAY2_PIN          5

    #define RELAY1_TYPE         RELAY_TYPE_NORMAL
    #define RELAY2_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            13
    #define LED1_PIN_INVERSE    0


// -----------------------------------------------------------------------------
// Electrodragon boards
// -----------------------------------------------------------------------------

#elif defined(ELECTRODRAGON_WIFI_IOT)

    // Info
    #define MANUFACTURER        "ELECTRODRAGON"
    #define DEVICE              "WIFI_IOT"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON2_PIN         2

    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON2_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    #define BUTTON1_RELAY       1
    #define BUTTON2_RELAY       2

    // Relays
    #define RELAY1_PIN          12
    #define RELAY2_PIN          13

    #define RELAY1_TYPE         RELAY_TYPE_NORMAL
    #define RELAY2_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            16
    #define LED1_PIN_INVERSE    0

// -----------------------------------------------------------------------------
// WorkChoice ecoPlug
// -----------------------------------------------------------------------------

#elif defined(WORKCHOICE_ECOPLUG)

    // Info
    #define MANUFACTURER        "WORKCHOICE"
    #define DEVICE              "ECOPLUG"

    // Buttons
    #define BUTTON1_PIN         13
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          15
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            2
    #define LED1_PIN_INVERSE    0

// -----------------------------------------------------------------------------
// AI Thinker
// -----------------------------------------------------------------------------

#elif defined(AITHINKER_AI_LIGHT)

    // Info
    #define MANUFACTURER        "AITHINKER"
    #define DEVICE              "AI_LIGHT"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_MY92XX
    #define DUMMY_RELAY_COUNT   1

    // Light
    #define LIGHT_CHANNELS      4
    #define MY92XX_MODEL        MY92XX_MODEL_MY9291
    #define MY92XX_CHIPS        1
    #define MY92XX_DI_PIN       13
    #define MY92XX_DCKI_PIN     15
    #define MY92XX_COMMAND      MY92XX_COMMAND_DEFAULT
    #define MY92XX_MAPPING      0, 1, 2, 3

// -----------------------------------------------------------------------------
// LED Controller
// -----------------------------------------------------------------------------

#elif defined(MAGICHOME_LED_CONTROLLER)

    // Info
    #define MANUFACTURER        "MAGICHOME"
    #define DEVICE              "LED_CONTROLLER"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1

    // LEDs
    #define LED1_PIN            2
    #define LED1_PIN_INVERSE    1

    // Light
    #define LIGHT_CHANNELS      4
    #define LIGHT_CH1_PIN       14      // RED
    #define LIGHT_CH2_PIN       5       // GREEN
    #define LIGHT_CH3_PIN       12      // BLUE
    #define LIGHT_CH4_PIN       13      // WHITE
    #define LIGHT_CH1_INVERSE   0
    #define LIGHT_CH2_INVERSE   0
    #define LIGHT_CH3_INVERSE   0
    #define LIGHT_CH4_INVERSE   0

    // IR
    #define IR_SUPPORT          1
    #define IR_PIN              4
    #define IR_BUTTON_SET       1

#elif defined(MAGICHOME_LED_CONTROLLER_20)

    // Info
    #define MANUFACTURER        "MAGICHOME"
    #define DEVICE              "LED_CONTROLLER_20"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1

    // LEDs
    #define LED1_PIN            2
    #define LED1_PIN_INVERSE    1

    // Light
    #define LIGHT_CHANNELS      4
    #define LIGHT_CH1_PIN       5       // RED
    #define LIGHT_CH2_PIN       12      // GREEN
    #define LIGHT_CH3_PIN       13      // BLUE
    #define LIGHT_CH4_PIN       15      // WHITE
    #define LIGHT_CH1_INVERSE   0
    #define LIGHT_CH2_INVERSE   0
    #define LIGHT_CH3_INVERSE   0
    #define LIGHT_CH4_INVERSE   0

    // IR
    #define IR_SUPPORT          1
    #define IR_PIN              4
    #define IR_BUTTON_SET       1

// -----------------------------------------------------------------------------
// HUACANXING H801 & H802
// -----------------------------------------------------------------------------

#elif defined(HUACANXING_H801)

    // Info
    #define MANUFACTURER        "HUACANXING"
    #define DEVICE              "H801"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1
    #define DEBUG_PORT          Serial1
    #define SERIAL_RX_PORT      Serial

    // LEDs
    #define LED1_PIN            5
    #define LED1_PIN_INVERSE    1

    // Light
    #define LIGHT_CHANNELS      5
    #define LIGHT_CH1_PIN       15      // RED
    #define LIGHT_CH2_PIN       13      // GREEN
    #define LIGHT_CH3_PIN       12      // BLUE
    #define LIGHT_CH4_PIN       14      // WHITE1
    #define LIGHT_CH5_PIN       4       // WHITE2
    #define LIGHT_CH1_INVERSE   0
    #define LIGHT_CH2_INVERSE   0
    #define LIGHT_CH3_INVERSE   0
    #define LIGHT_CH4_INVERSE   0
    #define LIGHT_CH5_INVERSE   0

#elif defined(HUACANXING_H802)

    // Info
    #define MANUFACTURER        "HUACANXING"
    #define DEVICE              "H802"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1
    #define DEBUG_PORT          Serial1
    #define SERIAL_RX_PORT      Serial

    // Light
    #define LIGHT_CHANNELS      4
    #define LIGHT_CH1_PIN       12      // RED
    #define LIGHT_CH2_PIN       14      // GREEN
    #define LIGHT_CH3_PIN       13      // BLUE
    #define LIGHT_CH4_PIN       15      // WHITE
    #define LIGHT_CH1_INVERSE   0
    #define LIGHT_CH2_INVERSE   0
    #define LIGHT_CH3_INVERSE   0
    #define LIGHT_CH4_INVERSE   0

// -----------------------------------------------------------------------------
// Jan Goedeke Wifi Relay
// https://github.com/JanGoe/esp8266-wifi-relay
// -----------------------------------------------------------------------------

#elif defined(JANGOE_WIFI_RELAY_NC)

    // Info
    #define MANUFACTURER        "JANGOE"
    #define DEVICE              "WIFI_RELAY_NC"

    // Buttons
    #define BUTTON1_PIN         12
    #define BUTTON2_PIN         13

    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON2_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    #define BUTTON1_RELAY       1
    #define BUTTON2_RELAY       2

    // Relays
    #define RELAY1_PIN          2
    #define RELAY2_PIN          14

    #define RELAY1_TYPE         RELAY_TYPE_INVERSE
    #define RELAY2_TYPE         RELAY_TYPE_INVERSE

#elif defined(JANGOE_WIFI_RELAY_NO)

    // Info
    #define MANUFACTURER        "JANGOE"
    #define DEVICE              "WIFI_RELAY_NO"

    // Buttons
    #define BUTTON1_PIN         12
    #define BUTTON2_PIN         13

    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON2_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    #define BUTTON1_RELAY       1
    #define BUTTON2_RELAY       2

    // Relays
    #define RELAY1_PIN          2
    #define RELAY2_PIN          14

    #define RELAY1_TYPE         RELAY_TYPE_NORMAL
    #define RELAY2_TYPE         RELAY_TYPE_NORMAL

// -----------------------------------------------------------------------------
// Jorge García Wifi+Relays Board Kit
// https://www.tindie.com/products/jorgegarciadev/wifi--relays-board-kit
// https://github.com/jorgegarciadev/wifikit
// -----------------------------------------------------------------------------

#elif defined(JORGEGARCIA_WIFI_RELAYS)

    // Info
    #define MANUFACTURER        "JORGEGARCIA"
    #define DEVICE              "WIFI_RELAYS"

    // Relays
    #define RELAY1_PIN          0
    #define RELAY2_PIN          2

    #define RELAY1_TYPE         RELAY_TYPE_INVERSE
    #define RELAY2_TYPE         RELAY_TYPE_INVERSE

// -----------------------------------------------------------------------------
// WiFi MQTT Relay / Thermostat
// -----------------------------------------------------------------------------

#elif defined(OPENENERGYMONITOR_MQTT_RELAY)

    // Info
    #define MANUFACTURER        "OPENENERGYMONITOR"
    #define DEVICE              "MQTT_RELAY"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_RELAY       1
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            16
    #define LED1_PIN_INVERSE    0

// -----------------------------------------------------------------------------
// WiOn 50055 Indoor Wi-Fi Wall Outlet & Tap
// https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50050-Indoor-Wi-Fi-Outlet-Wireless-Switch-Programmable-Timer-%2F263112281551
// https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338044841&mpre=http%3A%2F%2Fwww.ebay.com%2Fitm%2FWiOn-50055-Indoor-Wi-Fi-Wall-Tap-Monitor-Energy-Usage-Wireless-Smart-Switch-%2F263020837777
// -----------------------------------------------------------------------------

#elif defined(WION_50055)

    // Currently untested, does not support energy monitoring

    // Info
    #define MANUFACTURER        "WION"
    #define DEVICE              "50055"

    // Buttons
    #define BUTTON1_PIN         13
    #define BUTTON1_RELAY       1
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    // Relays
    #define RELAY1_PIN          15
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            2
    #define LED1_PIN_INVERSE    0

// -----------------------------------------------------------------------------
// EX-Store Wifi Relay v3.1
// https://ex-store.de/ESP8266-WiFi-Relay-V31
// -----------------------------------------------------------------------------

#elif defined(EXS_WIFI_RELAY_V31)

    // Untested

    // Info
    #define MANUFACTURER        "EXS"
    #define DEVICE              "WIFI_RELAY_V31"

    // Buttons
    #define BUTTON1_PIN         0
    #define BUTTON1_RELAY       1
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    // Relays
    #define RELAY1_PIN          13
    #define RELAY1_TYPE         RELAY_TYPE_LATCHED
    #define RELAY1_RESET_PIN    12

// -----------------------------------------------------------------------------
// V9261F
// -----------------------------------------------------------------------------

#elif defined(GENERIC_V9261F)

    // Info
    #define MANUFACTURER        "GENERIC"
    #define DEVICE              "V9261F"
    #define ALEXA_SUPPORT       0

    // V9261F
    #define V9261F_SUPPORT      1
    #define V9261F_PIN          2
    #define V9261F_PIN_INVERSE  1

// -----------------------------------------------------------------------------
// ECH1560
// -----------------------------------------------------------------------------

#elif defined(GENERIC_ECH1560)

    // Info
    #define MANUFACTURER        "GENERIC"
    #define DEVICE              "ECH1560"
    #define ALEXA_SUPPORT       0

    // ECH1560
    #define ECH1560_SUPPORT     1
    #define ECH1560_CLK_PIN     4
    #define ECH1560_MISO_PIN    5
    #define ECH1560_INVERTED    0

// -----------------------------------------------------------------------------
// ESPLive
// https://github.com/ManCaveMade/ESP-Live
// -----------------------------------------------------------------------------

#elif defined(MANCAVEMADE_ESPLIVE)

    // Info
    #define MANUFACTURER        "MANCAVEMADE"
    #define DEVICE              "ESPLIVE"

    // Buttons
    #define BUTTON1_PIN         4
    #define BUTTON2_PIN         5

    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON2_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH

    #define BUTTON1_RELAY       1
    #define BUTTON2_RELAY       2

    // Relays
    #define RELAY1_PIN          12
    #define RELAY2_PIN          13

    #define RELAY1_TYPE         RELAY_TYPE_NORMAL
    #define RELAY2_TYPE         RELAY_TYPE_NORMAL

    // DB18B20
    #ifndef DALLAS_SUPPORT
    #define DALLAS_SUPPORT             	1
    #endif
    #define DALLAS_PIN                 	2
    #define DALLAS_UPDATE_INTERVAL     	5000
    #define TEMPERATURE_MIN_CHANGE      1.0

// -----------------------------------------------------------------------------
// QuinLED
// http://blog.quindorian.org/2017/02/esp8266-led-lighting-quinled-v2-6-pcb.html
// -----------------------------------------------------------------------------

#elif defined(INTERMITTECH_QUINLED)

    // Info
    #define MANUFACTURER        "INTERMITTECH"
    #define DEVICE              "QUINLED"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1

    // LEDs
    #define LED1_PIN            5
    #define LED1_PIN_INVERSE    1

    // Light
    #define LIGHT_CHANNELS      2
    #define LIGHT_CH1_PIN       0
    #define LIGHT_CH2_PIN       2
    #define LIGHT_CH1_INVERSE   0
    #define LIGHT_CH2_INVERSE   0

// -----------------------------------------------------------------------------
// Arilux AL-LC06
// -----------------------------------------------------------------------------

#elif defined(ARILUX_AL_LC01)

    // Info
    #define MANUFACTURER        "ARILUX"
    #define DEVICE              "AL_LC01"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1

    // Light
    #define LIGHT_CHANNELS      4
    #define LIGHT_CH1_PIN       5       // RED
    #define LIGHT_CH2_PIN       12      // GREEN
    #define LIGHT_CH3_PIN       13      // BLUE
    #define LIGHT_CH4_PIN       14      // WHITE1
    #define LIGHT_CH1_INVERSE   0
    #define LIGHT_CH2_INVERSE   0
    #define LIGHT_CH3_INVERSE   0
    #define LIGHT_CH4_INVERSE   0


#elif defined(ARILUX_AL_LC02)

    // Info
    #define MANUFACTURER        "ARILUX"
    #define DEVICE              "AL_LC02"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1

    // Light
    #define LIGHT_CHANNELS      4
    #define LIGHT_CH1_PIN       12      // RED
    #define LIGHT_CH2_PIN       5       // GREEN
    #define LIGHT_CH3_PIN       13      // BLUE
    #define LIGHT_CH4_PIN       15      // WHITE1
    #define LIGHT_CH1_INVERSE   0
    #define LIGHT_CH2_INVERSE   0
    #define LIGHT_CH3_INVERSE   0
    #define LIGHT_CH4_INVERSE   0

#elif defined(ARILUX_AL_LC06)

    // Info
    #define MANUFACTURER        "ARILUX"
    #define DEVICE              "AL_LC06"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1

    // Light
    #define LIGHT_CHANNELS      5
    #define LIGHT_CH1_PIN       14      // RED
    #define LIGHT_CH2_PIN       12      // GREEN
    #define LIGHT_CH3_PIN       13      // BLUE
    #define LIGHT_CH4_PIN       15      // WHITE1
    #define LIGHT_CH5_PIN       5       // WHITE2
    #define LIGHT_CH1_INVERSE   0
    #define LIGHT_CH2_INVERSE   0
    #define LIGHT_CH3_INVERSE   0
    #define LIGHT_CH4_INVERSE   0
    #define LIGHT_CH5_INVERSE   0


#elif defined(ARILUX_AL_LC11)

    // Info
    #define MANUFACTURER        "ARILUX"
    #define DEVICE              "AL_LC11"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1

    // Light
    #define LIGHT_CHANNELS      5
    #define LIGHT_CH1_PIN       5       // RED
    #define LIGHT_CH2_PIN       4       // GREEN
    #define LIGHT_CH3_PIN       14      // BLUE
    #define LIGHT_CH4_PIN       13      // WHITE1
    #define LIGHT_CH5_PIN       12      // WHITE1
    #define LIGHT_CH1_INVERSE   0
    #define LIGHT_CH2_INVERSE   0
    #define LIGHT_CH3_INVERSE   0
    #define LIGHT_CH4_INVERSE   0
    #define LIGHT_CH5_INVERSE   0


#elif defined(ARILUX_E27)

    // Info
    #define MANUFACTURER        "ARILUX"
    #define DEVICE              "E27"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_MY92XX
    #define DUMMY_RELAY_COUNT   1

    // Light
    #define LIGHT_CHANNELS      4
    #define MY92XX_MODEL        MY92XX_MODEL_MY9291
    #define MY92XX_CHIPS        1
    #define MY92XX_DI_PIN       13
    #define MY92XX_DCKI_PIN     15
    #define MY92XX_COMMAND      MY92XX_COMMAND_DEFAULT
    #define MY92XX_MAPPING      0, 1, 2, 3

// -----------------------------------------------------------------------------
// XENON SM-PW701U
// -----------------------------------------------------------------------------

#elif defined(XENON_SM_PW702U)

    // Info
    #define MANUFACTURER        "XENON"
    #define DEVICE              "SM_PW702U"

    // Buttons
    #define BUTTON1_PIN         13
    #define BUTTON1_MODE        BUTTON_PUSHBUTTON | BUTTON_DEFAULT_HIGH
    #define BUTTON1_RELAY       1

    // Relays
    #define RELAY1_PIN          12
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL

    // LEDs
    #define LED1_PIN            4
    #define LED1_PIN_INVERSE    1

// -----------------------------------------------------------------------------
// AUTHOMETION LYT8266
// https://authometion.com/shop/en/home/13-lyt8266.html
// -----------------------------------------------------------------------------

#elif defined(AUTHOMETION_LYT8266)

    // Info
    #define MANUFACTURER        "AUTHOMETION"
    #define DEVICE              "LYT8266"
    #define RELAY_PROVIDER      RELAY_PROVIDER_LIGHT
    #define LIGHT_PROVIDER      LIGHT_PROVIDER_DIMMER
    #define DUMMY_RELAY_COUNT   1

    // Light
    #define LIGHT_CHANNELS      4
    #define LIGHT_CH1_PIN       13      // RED
    #define LIGHT_CH2_PIN       12      // GREEN
    #define LIGHT_CH3_PIN       14      // BLUE
    #define LIGHT_CH4_PIN       2       // WHITE
    #define LIGHT_CH1_INVERSE   0
    #define LIGHT_CH2_INVERSE   0
    #define LIGHT_CH3_INVERSE   0
    #define LIGHT_CH4_INVERSE   0

    #define LIGHT_ENABLE_PIN    15

// -----------------------------------------------------------------------------
// Generic 8CH
// -----------------------------------------------------------------------------

#elif defined(GENERIC_8CH)

    // Info
    #define MANUFACTURER        "GENERIC"
    #define DEVICE              "8CH"

    // Relays
    #define RELAY1_PIN          0
    #define RELAY1_TYPE         RELAY_TYPE_NORMAL
    #define RELAY2_PIN          2
    #define RELAY2_TYPE         RELAY_TYPE_NORMAL
    #define RELAY3_PIN          4
    #define RELAY3_TYPE         RELAY_TYPE_NORMAL
    #define RELAY4_PIN          5
    #define RELAY4_TYPE         RELAY_TYPE_NORMAL
    #define RELAY5_PIN          12
    #define RELAY5_TYPE         RELAY_TYPE_NORMAL
    #define RELAY6_PIN          13
    #define RELAY6_TYPE         RELAY_TYPE_NORMAL
    #define RELAY7_PIN          14
    #define RELAY7_TYPE         RELAY_TYPE_NORMAL
    #define RELAY8_PIN          15
    #define RELAY8_TYPE         RELAY_TYPE_NORMAL

// -----------------------------------------------------------------------------

#endif

// -----------------------------------------------------------------------------
// Check definitions
// -----------------------------------------------------------------------------
#if not defined(MANUFACTURER) || not defined(DEVICE)
    #error "UNSUPPORTED HARDWARE!!"
#endif