* add support for idobao id80 iso layout
* This change is required as there is a logic bug on the board that C7
(capslock) is inverted thus lowercase is with light on. Mind the ! in
the write to the pin.
* Apply suggestions from code review
All fine for me, thanks for the additional information!
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* move device information to separate config.h for id80 iso and ansi
* commit via keymap similar to default. There is a problem with mapping compiling vor via, resulting in KC_ENT residing on KC_PGDN. Switching off via support in rules.mk makes the keyboard behave fine
* change KC_BSLS to KC_NUHS as this is an iso board
Co-authored-by: Carsten <modebm@gmail.com>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* id80: Transpose matrix to use faster COL2ROW routines
Even the standard QMK matrix_scan() function can give about 2 times
higher scan rate (if compiled with optimizations enabled) if the COL2ROW
matrix layout is used instead of ROW2COL. Although the ID80 PCB is
wired using the ROW2COL matrix layout, it is possible to transpose the
matrix from the QMK standpoint, so that "columns" would correspond to
horizontal connections, and "rows" would correspond to (mostly) vertical
connections; in this case the matrix could be handled as if it had the
COL2ROW layout.
The matrix layout change makes the older VIA JSON layout definition
incompatible, but the corresponding JSON was not yet accepted to the VIA
repository, so it should still be safe to make this change.
* id80: Remove obsolete comments
* id80: New keyboard (IDOBAO ID80)
Add initial support for the IDOBAO ID80 keyboard.
Most source files were generated by the KBFirmware JSON to QMK Parser
(https://noroadsleft.github.io/kbf_qmk_converter/) based on the
ID80.json file provided by the keyboard vendor. The only change to
rules.mk was to set `COMMAND_ENABLE = no` to make the compiled firmware
fit into the available flash space.
* id80: Update default keymap to match stock
Update the Fn layer in the default keymap to match the stock firmware
which was actually flashed into the PCB.
* id80: Add Caps Lock indicator support
Although the KBFirmware JSON includes information about the MCU pins
used for keyboard indicator LEDs, the KBF to QMK converter does not
generate the required code automatically. Implement the LED handling
code, and at the same time switch from the older `led_set_kb` API to the
newer `led_update_kb`.
* id80: Remove placeholder functions
The provided skeletons for `matrix_scan_kb` and `process_record_kb` did
not do anything useful, so remove them.
* id80: Use Esc as the Bootmagic Lite activation key
The Esc key is not at the (0, 0) position in the ID80 matrix, therefore
setting `BOOTMAGIC_LITE_ROW` and `BOOTMAGIC_LITE_COLUMN` is required to
use the Esc key for Bootmagic Lite.
* id80: Update info.json
Replace info.json generated by the KBF to QMK converter with another
version generated using http://www.keyboard-layout-editor.com/ and the
KLE raw to QMK info.json converter (https://qmk.fm/converter/). The
updated info.json has the correct physical layout (the distance between
the function key row and the main block is actually 0.25U, but the
vendor-provided ID80.json had 0.5U there) and correct key labels (using
the stock layout instead of raw matrix locations and pin names).
* id80: Enable NKRO
The default keymap is updated to have NK_TOGG at Fn+N, like most other
keyboards which have NKRO enabled.
* id80: Use unique USB vendor/product ID
Having an unique USB vendor/product ID is required for VIA support.
The vendor ID value is the same as for the `idobo` (ID75) keyboard.
* id80: Fix right modifiers in the default keymap
For some reason the default keymap converted from the vendor-supplied
JSON had the right Shift, Alt and Ctrl keys mapped to the left side
modifier keycodes.
* id80: Remove empty row 6 (F0) from matrix
The matrix layout which was defined in the vendor-supplied ID80.json
file had 12 rows which corresponded to the left and right parts of the
6 physical rows. However, the row 6 of the matrix (connected to the F0
pin), which corresponded to the right part of the physical bottom row,
was completely empty (all 9 keys of the bottom row were placed in the
matrix row for the left part). Keeping this row in the matrix just
wastes resources; in particular, when the VIA support is enabled, having
a 9×12 matrix with 4 layers leaves only 122 bytes available for dynamic
macros, which is less than the recommended minimum of 128 bytes.
Removing the unused row reduces the matrix size to 9×11, which leaves
194 bytes of EEPROM space for dynamic macros.
* id80: Update row numbers in the LAYOUT macro
Update row numbers in the names of the LAYOUT macro parameters after
removing a row in the middle.
* id80: Set RGBLED_NUM to 20 to match the actual PCB
The vendor-supplied ID80.json file specified that the PCB should have
28 RGB LEDs in the chain. However, the actual PCB that was shipped
from AliExpress had 20 LEDs in the chain (16 underglow LEDs, and then 4
more LEDs on top of the PCB, to the right of the Enter key location).
Update RGBLED_NUM to match the actual PCB.
* VIA support for Think6.5
* VIA support for Think6.5 Hotswap
* VIA works better with separate layout options
* Remove the colours used to help develop it in KLE
* Pay better attention to the JSON linter
* Update Think6.5 PRODUCT and remove VIA JSON defs
* generated files
* create the physical and electrical matrix, thanks noroadsleft
* add an appropriate keymap
* add qmk configurator support
* add readme
* add keyboard configuration and rules
* move over the think6.5 to the gray_studio directory
* move to hotswap in anticipation of non hotswap pcb support
* update readme to have the correct make path
* rename to hotswap
* add community layout support by using the LAYOUT_65_ansi_blocker LAYOUT macro name
* thanks to cygnus for pointing out the solder json file to me. This commit is pretty much the same as the hotswap as it uses the same pins and switch matrix.
* update readme to state that LAYOUT_65_ansi_blocker works for both hotswap and solder.
* wrong pound include
* add LED support. Soldered PCB only supports caps lock LED
* add readme notes for indicator led
* Update keyboards/gray_studio/think65/hotswap/keymaps/default/keymap.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update keyboards/gray_studio/think65/hotswap/rules.mk
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update keyboards/gray_studio/think65/hotswap/rules.mk
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update keyboards/gray_studio/think65/solder/keymaps/default/keymap.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update keyboards/gray_studio/think65/solder/rules.mk
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update keyboards/gray_studio/think65/solder/rules.mk
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* new keyboard bm43a
* Thanks to noroads for generating this with his online tool
* add QMK Configurator support thanks to noroads
* turn on bootmagic lite
* update readme
* remove unneeded comments
* Add default value for IS_COMMAND for COMMAND feature
* Cleanup and consistency
* Update Templates to reflect change
* Fix IS_COMMAND in template
* Fix IS_COMMAND define
* Use consistent IS_COMMAND block in templates
* Remove unnecessary `#undef IS_COMMAND` directives
* Fix compile issue on orthodox
* Reomve IS_COMMAND option for newer boards
* Remove all existing definitions of IS_COMMAND if they use default LSHIFT and RSHIFT setting
* Remove a couple of additional IS_COMMAND defines
* Remove remaining redundant IS_COMMAND definitions
* Remove #undef IS_COMMAND from orthodox:drashna and whitefox:konstantin
* Remove multiple empty lines in modified config.h files
* Update additional boards
* Reomve IS_COMMAND from newer boards
* Update Alice keyboard
* Remove IS_COMMAND from additional boards
Jan 24th edition
* Add H87a keymap and info
* Create readme.md
* Add h87a .json for kbfirmware.com use
* Update readme.md
* Update readme.md
* Update h87a files
* Delete Makefile
* Update readme.md
* Delete desktop.ini
* update files to match new QMK framework
* Update files to match new QMK structure
* Update files to match new QMK structure
* add layout name information
* Add info.json
* update keymap to support layout_all
* update keymap to support layout_all
* update rules.mk to fix filesize
* Update readme.md
* Update config.h
* Update readme.md
* Update config.h
* Update config.h
Add "define CONFIG_H and include "config_common.h" back to file
- Backlight on PB7 controlled by Timer1 Fast PWM (no interrupts).
- Backlight commands connected temporarily to top left keys.
- Backlight init called from matrix.c, since there's no generic keyboard_init() override function.